Table of Contents
Advertisement
1. Wi-Fi interface introduction (Remote controller pairing)
MSZ-LN18VG2W-
,
,
E3
ER2
ET2
MSZ-LN18VG2V/B/R-
E3
MSZ-LN25VG2W/V/B/R-
E3
MSZ-LN35VG2W/V/B/R-
E3
MSZ-LN50VG2W/V/B/R-
E3
MSZ-LN60VG2W/V/B/R-
E3
NET LED
It shows the network state.
(Refer to 8-5.3-3. NET LED.)
2. Setting up
Set up a connection between the Wi-Fi module and the
router.
NOTE:
Setup is possible only after operating the air conditioner
using the wireless remote controller.
For MELCloud User Manual, please go to the website
below.
www.melcloud.com/Support
3. Selecting a mode
The Wi-Fi module has to be paired with the router in
order for communication between the indoor unit and
MELCloud to begin. There are 2 methods of pairing the
Wi-Fi module with the router:
• WPS-PUSH mode
• Access Point mode
The mode to be set depends on whether your router has
the WPS button.
Use the pairing mode most suitable for your system.
Follow the instructions below to set the pairing mode with
Remote controller.
Set up the Wi-Fi module and the router again when the
router has been replaced.
To reset connection and set up the Wi-Fi module and the
router again
(1) Hold down the Temperature
for 5 seconds.
(2) Select "_ 2" by pressing Tempera-
ture
and
.
(3) Point the remote controller
toward the indoor unit and press
the
.
(4) The indoor unit beeps 3 times
when resetting is complete.
OBH766G
,
SC1
,
,
,
SC1
ER3
ET3
,
,
,
SC1
ER3
ET3
,
,
,
SC1
ER3
ET3
,
,
ER3
ET3
Wi-Fi
INTERFACE
XXXXXXXX
MODEL
MAC
: XXXXXXXXXXXX
ID
: XXXXXXXXXX
SSID
: XXXXXXXXXXXX
KEY
: XXXXXXXXXXXX
VOLTAGE
:
:
CURRENT
ERR
MITSUBISHI ELECTRIC CORPRATION
NET
MODE
UNIT
RESET
MODE
WiFi.ASSY DWG No.
XXXXXXXXXXX
MADE IN CHINA
3-1. Setting up in WPS-PUSH mode
To enter the mode
(1) Hold down the Temperature
5 seconds.
(2) Select "¯ 2" by pressing
Temperature
on the right.
(3) Point the remote controller
toward the indoor unit and press
>PP<
the
.
XXXXXXXXXX
3-1.1. Connect the router to the air conditioner.
Make sure that the LED (Air purifying lamp of the
indoor unit) indication is as shown below.
Push WPS button of the router within 2 minutes
after the mode selection has completed.
The WPS-PUSH mode will return to initial state
if WPS button is not pressed for 2 minutes.
Connecting
Router
3-1-2. LED (Air purifying lamp of the indoor unit) will be
as shown below when connection between the
router and Wi-Fi module is completed and
connection to MELCloud starts.
Connected
Connecting
MELCloud
NOTE:
If the indication LED (Air purifying lamp of the indoor
unit) does not change or blinks 5 times, connection
fails.Please reset connection and setup the Wi-Fi
module and the router again.
Main causes that WPS failed are as follows.
Communication distance (from the Wi-Fi module to
router), router settings (encryption, authentication, limit
of connections, etc.)
22
WPS-Push mode
for
and
as shown
The LED (Air purifying lamp of the indoor unit)
lights up for 3 seconds then blinks twice.
A beep sounds as the LED (Air purifying lamp
of the indoor unit) blinks.
This series of actions is repeated.
The LED (Air purifying lamp of the indoor unit)
lights up for 5 seconds and then a beep
sounds for 1 second.
Advertisement
Table of Contents
