Advertisement
Device Installation/ 设备安装
E. Beam-Mounted Installation/ 横臂抱装
Loosen the two hose clamps and remove them. Install the universal
1
joint in the #2 holes on the pole mount, as shown in the figure below.
Adjust the horizontal angle as needed during installation.
将 2 个喉箍拧开， 卸下支架上的喉箍环。 将万向节安装到抱装支架 2 号孔位 （如
下图，安装时注意调整好水平监控角度）。
Cable Connection/ 连接线缆
A. Cable Connection/ 连接线缆
CAUTION/ 注意
• This camera is frss from grounding.
该型号摄像机为免接地摄像机，不需要做接地处理。
• In areas prone to lightning strikes, the lightning arrester must be installed and grounded.
在易受雷击的区域，必须安装避雷器，避雷器必须接地。
• Strong and weak current cables must be kept at least 5 cm apart from each other. When connecting the
cables to the device, take care to avoid connecting strong current cables to weak current interfaces or
you will damage your device.
强电和弱电必须分开布线，两者间的距离不小于 5cm。线缆与设备连接时，禁止将强电接到弱电接口上，以免造
成设备损坏。
• Wrap all pigtail cables in insulated, waterproof, rubber tape to prevent short circuits or water damage.
Cutting off the pigtail cables will void your warranty.
请务必使用绝缘胶带和防水胶带对所有尾线进行绝缘和防水处理，以免造成短路和漏水。尾线不能剪断，若剪断，
则无法维保。
Connect the power cable.
1
连接电源线。
Unfasten the screw marked with a on the universal joint for
2
the universal joint to rotate freely. Fasten screws marked
with b and c to fix the camera to the universal joint. Adjust
the vertical monitoring angle, and fasten all screws on the
universal joint.
拧松万向节上 a 处的螺钉，使得万向节可以自由转动。拧紧 b 和 c
两处的螺钉，将摄像机固定到万向节上。调整好垂直监控角度，拧
紧万向节上的所有螺钉。
b
a
c
Connect the network cable. Loosen the components 1, 2, and 3 of the waterproof connector kit on the network
2
cable port in sequence, thread the network cable through the kit (If the network cable cannot be threaded
through the kit, cut off the RJ45 connector.), and install the components in the sequence marked in the
following figure. The waterproof connector of the network cable must be secured tightly, or they may come
loose later.
连接网线。 先把网线接口上防水套件的组件 1、 组件 2 和组件 3 依次旋转拆卸， 然后穿入网线 （如果无法穿入， 请剪掉水晶头） ，
再将各组件按如图所示顺序安装。网线防水接头务必拧紧到位，否则会有脱落风险。
O-ring for the waterproof connector (rubber ring)
网线防水接头密封圈（细橡皮圈）
Connect the audio cable.
3
连接音频线。
5
Thread the hose clamps through the installation holes on the pole mount.
3
Place the hose clamps around the beam and tighten them up.
将 2 个喉箍环穿过抱装支架的安装孔，并环绕在横臂上，拧紧喉箍。
1
Component 3
Component 2
组件 3
组件 2
2
3
4
Component 1
组件 1
Advertisement
