Sharp PN-A601 Professional LCD Monitor Operation Manual page 25

nOPTION
DATE/TIME SETTING
Set the date and time. Press
and time, and press or
values.
Set the date in "Month/Day/Year" order.
Set the time on a 12-hour basis. (Factory default)
DATE/TIME FORMAT
Sets the date/time display format.
DATE .................. M M/DD/YYYY
DD/MM/YYYY
YYYY/MM/DD
(YYYY: Year, MM: Month, DD: Day)
TIME ................... S elect 12- or 24-hour time.
SCHEDULE (See page 28.)
You can turn the power on/off and change the screen
brightness at a specified time.
INPUT SELECT
Select the input mode to be used in PC D-Sub input terminal,
PC/AV DVI-D input terminal, PC/AV HDMI input terminal and
PC RGB/AV component input terminals.
For D-SUB, select SET after selecting the input mode, and
MENU
then press .
D-SUB and BNC cannot be set to AV COMPONENT at the
same time.
If D-SUB is set to AV VIDEO, the AV VIDEO input terminal
cannot be used for BNC.
AUDIO SELECT
Selects the terminal used to input audio signals in each input
mode.
INPUT SIGNAL (PC D-SUB/PC RGB)
If a computer connected to the PC D-sub/PC RGB input
terminal outputs any of the following resolutions, make a
selection from the following options.
480 LINES .......... AUTO, 640x480 or 848x480
768 LINES .......... A UTO, 1024x768, 1280x768 or 1360x768
1050 LINES ........1400x1050 or 1680x1050
ZOOM2 SPECIAL SETTING (See page 28.)
SCAN MODE (AV input)
Sets the scan mode used for AV mode input.
MODE1 ............... O ver-scan display
MODE2 ...............Under-scan display
MODE3 ............... U nder-scan display when the input signal
is 1080i/p. Otherwise, over-scan display
* E ven when MODE1 is selected, under-scan display is used
when the input signal is 1080i/p and the screen size is Dot
by Dot.
POWER MANAGEMENT
POWER MANAGEMENT determines whether or not to
switch modes from no signal to the input signal standby
mode.
COLOR SYSTEM (AV S-VIDEO/AV VIDEO)
Select the color system of the AV equipment which is
connected to AV S-video and AV video input terminal. (AUTO /
PAL / PAL-60 / SECAM / NTSC3.58 / NTSC4.43)
When AUTO is selected, the color system is automatically set
according to the input signal.
or to select the date
to change the numerical
AUDIO OUTPUT(RCA)
Sets the volume of sound output from the audio output
terminals. When set to VARIABLE2, audio is not output from
the external speaker terminals.
VARIABLE .......... You can adjust the volume using VOLUME.
FIXED ................. Disables volume adjustment and fixes the
sounds.
When the PN-ZB01 (optional) is attached:
VARIABLE1 ........ You can adjust the volume using VOLUME.
VARIABLE2 ........ You can adjust the volume using VOLUME,
but audio is not output from the external
speaker terminals.
FIXED ................. Disables volume adjustment and fixes the
sounds.
AUDIO LEVEL(STEREO MINI)
Selects the maximum audio input level of the audio input
terminal.
SELF ADJUST
On a PC D-SUB/PC RGB screen, specify whether to
perform screen adjustment automatically or not. When ON
is selected, the screen is automatically adjusted when its
resolution is 800 x 600 or higher and the timing of input
signals changes. "ADJUSTING" appears on the screen
during the adjustment. For images with black edges, etc.,
depending on the signal, adjustment may not be possible.
In this case select OFF. (Perform manual adjustment of the
screen.)
AUTO INPUT CHANGE
Specify whether to change inputs automatically. When ON is
selected and no signal is present in the selected input mode,
AUTO INPUT CHANGE automatically changes the selected
mode to another mode where a video signal is present.
When video signals exist in multiple input modes, the
switching priority is as follows:
PC D-SUB, PC HDMI, AV HDMI, AV COMPONENT and AV
VIDEO
When the PN-ZB01 (optional) is attached:
PC DVI-D, PC HDMI, PC D-SUB, PC RGB, AV DVI-D, AV
HDMI, AV COMPONENT, AV S-VIDEO and AV VIDEO
(Input mode switching may take 15 seconds or more,
depending on the connected equipment. Input signals
may not be detected properly and a priority may change,
depending on the connected equipment or video signals.)
FAN SPEED
Sets the rotation speed of the fan.
As this number increases, the rotation speed becomes
faster. When set to AUTO, the rotation speed of the fan will
change depending on the internal temperature.
Menu Items
25
E