BOMANN GSP 861 Instruction Manual page 8

• The setting is automatically saved after a few
seconds; alternatively end the setup with the
Power button.
Water hardness Water hardness Water hardness Water hardness
Setting Setting
Setting Setting
°dH °dH Mmol/l Mmol/l
°dH °dH Mmol/l Mmol/l
0-5 0-0.94 H1
6-11 1.0-2.0 H2
12-17 2.1-3.0 H3
18-22 3.1-4.0 H4
23-34 4.1-6.0 H5
35-55 6.1-9.8 H6
NOTE NOTE: : : : NOTE NOTE
°dH: German degree of hardness
Factory setting: H3
Fill in the salt Fill in the salt Fill in the salt Fill in the salt
CAUTION: CAUTION: CAUTION: CAUTION:
• Only refill the salt container when the salt warning
lamp is lighting.
• During filling the salt container, salt and water can
escape. Start a program immediately after you
have filled the container to prevent corrosion.
• Remove the lower basket and unscrew the lid of
the salt container.
• Add about 1.5 kg of salt by using the supplied
funnel tube.
• Full fill the salt container with water (just before
the first use).
• Screw the lid firmly on again after filling the con-
tainer.
• Depending on salt resolution, the warning lamp
usually disappears immediately after filling.
Fill the rinse aid dispenser Fill the rinse ai d dispenser
Fill the rinse ai Fill the rinse ai d dispenser d dispenser
B B B B . . . .
Function of rinse aid Function of rinse aid
Function of rinse aid Function of rinse aid
The rinse aid is automatically added during the final
rinse, ensuring thorough rinsing and a spot and
streak free drying.
Control lamps Control lamps Salt cons. Salt cons.
Control lamps Control lamps Salt cons. Salt cons.
lights lights lights lights / c / c / cycle / c ycle ycle ycle
Rapid 0 g
90 Min. 9 g
90 Min + Rapid 12 g
Glass 20 g
Glass + Rapid 30 g
Glass + 90 Min. 60 g
When to refill the rinse aid dispenser When to refill the rinse aid dispenser
When to refill the rinse aid dispenser When to refill the rinse aid dispenser
As long as the corresponding
message does not light up in the
display, you can estimate the
amount of remaining rinse aid to the optical level
indicator (D D D D ) next to the dispenser.
When the rinse aid dispenser is full, the indicator is
completely dark. If the rinse aid diminishes, the size
of the black dot changes as shown below. In order to
avoid spotting, the rinse aid level must not drop be-
low ¼.
full ¾ full
Fill in the rinse aid Fill in the rinse aid Fill in the rinse aid Fill in the rinse aid
• To open the dispenser screw the lid counter-
clockwise to the open position and remove the lid.
• Add the rinse aid into the dispenser, being careful
not to overfill. The dispenser contains approx.
110 ml.
• Before closing the appliance door, put on the lid in
the open position back and turn it clockwise to the
closed position.
NOTE: : : : NOTE NOTE NOTE
Remove spilled rinse aid with an absorbent cloth to
avoid excessive foaming during the next rinse.
Adjusting the rinse aid dosage Adjusting the rinse aid dosage Adjusting the rinse aid dosage Adjusting the rinse aid dosage
When forming spots and the dishes dries poorly,
increase the added amount of rinse aid. You can set
the amount of addition between level 1 (min.) and
level 6 (max.).
Take off the lid of the rinse aid dispenser
and adjust the dial to the desired level.
The factory setting is "4".
NOTE NOTE: : : :
NOTE NOTE
Increase the dosage if there are drops of water or
lime spots on the dishes after rinsing. Reduce the
8
½ full ¼ full empty