Download  Print this page

Advertisement

MINI COMPONENT SYSTEM
MODEL
CD-BA250
CD-BA2600
OPERATION MANUAL
CD-BA250(FRONT)
1
Thank you for purchasing this SHARP product.
To obtain the best performance from this product, please read this
manual carefully. It will guide you in operating your SHARP product.
CD-BA250 Mini Component System consisting of CD-BA250 (main
unit) and CP-BA250 (speaker system).
CD-BA2600 Mini Component System consisting of CD-BA2600 (main
unit) and CP-BA2600 (speaker system).
00.12.27, 1:35 PM

Advertisement

   Related Manuals for Sharp CD-BA250

   Summary of Contents for Sharp CD-BA250

  • Page 1 Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. CD-BA250 Mini Component System consisting of CD-BA250 (main unit) and CP-BA250 (speaker system).
  • Page 2 NOTE It is the intent of Sharp that this product be used in full compliance with the copyright laws of the United States and that prior permission be obtained from copyright owners whenever necessary.
  • Page 3 Important Safeguards CAUTION All the safety and operating instructions should be read before the appliance is operated, and should be retained for future reference. Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure your personal safety. Improper use can result in potential electrical shock or fire hazards.
  • Page 4: Table Of Contents

    Contents „ General Information Accessories ............4 Precautions .
  • Page 5: Precautions

    SHARP will not be held responsible for any damage resulting from use of this unit with a voltage other than that which is specified.
  • Page 6: Controls And Indicators

    Controls and Indicators 23 24 25 Description of remote control (See page 8.) „ Front panel 1. Disc Tray ..........16 2.
  • Page 7 1. FM/AM Loop Antenna Jack ......10, 11 2. Video/Auxiliary (Audio Signal) Input Jacks ....28 3.
  • Page 8 Controls and Indicators (continued) Battery installation for remote control (See page 12.) „ Remote control 1. Remote Control Transmitter ....... . .12 2.
  • Page 9 „ Speaker system 1. Tweeter 2. Woofer 3. Bass Reflex Duct 4. Speaker Wire Speaker grilles are removable: Make sure nothing comes into contact with the speaker diaphragms when you remove the speaker grilles. Placing the speaker system: There is no distinction between the right and the left speakers. Left speaker 00/12/4 CD-BA250(U)1.fm...
  • Page 10: System Connections

    System Connections FM antenna AM loop antenna Left speaker Right speaker VCR, DVD, etc. not supplied AC outlet (AC 120 V, 60 Hz) 00/12/4 CD-BA250(U)1.fm...
  • Page 11 „ Speaker connection Connect the black wire to the minus (-) terminal, and the red wire to the plus (+) terminal. Right speaker Black Caution: z Use speakers with an impedance of 6 ohms or more, as lower impedance speakers can damage the unit.
  • Page 12: Remote Control

    Remote Control „ Battery installation Use 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar). Batteries are not included. 1 Remove the battery cover. 2 Insert the batteries according to the direction indicated in the bat- tery compartment. When inserting or removing the batteries, push them toward the nals.
  • Page 13: General Control

    General Control „ Demonstration mode The first time the unit is plugged, the unit will enter the demonstration mode. You will see words scroll. To cancel the demonstration mode: When the unit is in the power stand-by mode (demonstration mode), press the X- BASS/DEMO button.
  • Page 14: Sound Control

    Sound Control „ Volume control Press the VOLUME button to increase the volume and the VOLUME decreasing. 0 1 2 29 30 MAXIMUM „ Bass control When the power is first turned on, the unit will enter the extra bass mode which emphasizes the bass frequencies, and "X-BASS"...
  • Page 15: Setting The Clock

    Setting the Clock In this example, the clock is set for the 12-hour (AM 12:00) display. Press the ON/STAND-BY button to turn the power on. Press the CLOCK button and within 5 seconds, press the MEMO- RY/SET button. Press the TUNING/TIME ( ) button to select 12-hour or 24- hour display and then press the MEMORY/SET button.
  • Page 16: Listening To A Cd (cds)

    Listening to a CD (CDs) This system can play audio CD-R and CD-RW discs just as CD discs, but cannot per- form recording. Sound Control (See page 14.) Press the ON/STAND-BY button to turn the power on. Press the CD button.
  • Page 17 Press the / ( ) button to start playback. z Playback will begin from track 1 on the disc you have selected to play. After that disc finishes playing, the next disc will automatically start playback. z When the last track on the third disc has finished playing, the CD player will stop automatically.
  • Page 18: Starting Playback With A Desired Track

    Starting playback with a desired track You can play a disc starting with the desired track. While in the stop mode, press one of the remote control or DISC SKIP button to select the desired disc. Selected disc number Press the PRESET PRESET desired track.
  • Page 19: Programmed Play

    Programmed Play By specifying discs from 1 to 3 and tracks from 1 to 99, you can choose up to 32 selections for playback in the order you like. Selected disc number While in the stop mode, press one of the 3 buttons on the remote control to select the desired disc.
  • Page 20: Listening To The Radio

    Listening to the Radio Sound Control (See page 14.) Press the ON/STAND-BY button to turn the power on. Press the TUNER (BAND) button repeatedly to select the desired frequency band (FM or AM). Press the TUNING/TIME ( ) button to tune in to the desired station.
  • Page 21: Listening To The Memorized Station

    Listening to the memorized station „ Memorizing a station You can store 40 AM and FM stations in memory and recall them at the push of a but- ton. (Preset tuning) Perform the steps 1 - 3 in "Listening to the Radio" on page 20. Press the MEMORY/SET button to enter the preset tuning saving mode.
  • Page 22: Listening To A Cassette Tape (tape 1 Or Tape 2)

    Listening to a Cassette Tape (TAPE 1 or TAPE 2) Before playback: z For playback, use normal or low-noise tapes for the best sound. (Metal or CrO tapes are not recommended.) z Do not use C-120 tapes or poor-quality tapes, as they may cause mal- functions.
  • Page 23: Recording From The Radio

    When recording important selections, make a preliminary test to ensure that the desired material is properly recorded. z SHARP is not liable for damage or loss of your recording arising from malfunction of this unit. z The volume and sound controls can be adjusted with no effect on the recorded signal (Variable Sound Monitor).
  • Page 24: Recording From A Cd (cds)

    Recording from a CD (CDs) Programmed Play (See page 19.) You can record 3 CDs continuously. Press the ON/STAND-BY button to turn the power on. Load a cassette into the TAPE 2 cassette compartment with the side to be recorded on facing you. Wind past the leader of the tape, on which recording cannot be performed.
  • Page 25: Dubbing From Tape To Tape

    Dubbing from Tape to Tape You can record from TAPE 1 to TAPE 2. For recording, use only normal tapes. Do not use metal or CrO tapes. Press the ON/STAND-BY button to turn the power on. Load a prerecorded cassette into the TAPE 1 cassette compart- ment.
  • Page 26: Timer And Sleep Operation

    Timer and Sleep Operation Timer playback: The unit turns on and plays the desired source (CD, tuner, tape) at the preset time. Timer recording: The unit turns on and starts recording from the tuner at the preset time. Sleep operation: The radio, compact disc and cassette tape can all be turned off automatically.
  • Page 27 Press the TUNING/TIME ( or ) button to specify the minute, then press the MEMORY/SET button. The unit will enter the timer stand-by mode automatically. To cancel the timer playback/timer recording: Press the ON/STAND-BY button to turn the power on. When the preset time is reached, playback or recording will start.
  • Page 28: Enhancing Your System

    VCR, DVD, etc. Use a connection cord to connect the VCR, DVD, etc. to the VIDEO/ AUX jacks. When using video equipment, connect the audio output to this unit and the video output to a television. To the line output jack Press the ON/STAND-BY button to turn the power on.
  • Page 29: Troubleshooting Chart

    Troubleshooting Chart Many potential "problems" can be resolved by the owner without calling a service technician. If something is wrong with this product, check the following before calling your autho- rized SHARP dealer or service center. „ General Symptom Possible cause z The clock is not on time.
  • Page 30: Maintenance

    Troubleshooting Chart (continued) „ If trouble occurs When this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is operated incorrectly, it may malfunction. If such a problem occurs, do the following: Set the unit to the stand-by mode and turn the power on again.
  • Page 31: Specifications

    Specifications As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.
  • Page 32: Consumer Limited Warranty

    Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer.

This manual also for:

Cd-ba2600

Comments to this Manuals

Symbols: 0
Latest comments: