Page 1
CTs Multi-Channel Series Operation Manual CTs 4200 CTs 8200 Obtaining Other Language Versions: To obtain information in another language about the use of this product, please contact your local Crown Distributor. If you need assistance locating your local distributor, please contact Crown at 574-294-8000. This manual does not include all of the details of design, production, or variations of the equipment.
CTs Power Amplifiers CTs Power Amplifiers Important Safety Instructions Wichtige Sicherheitsinstruktionen DECLARATION of CONFORMITY Crown Audio, Inc. Importantes Instructions de Sécurité Instrucciones de Seguridad Importantes iMPORTaNT CTs Series amplifiers require Class 2 output wiring. FOR COMPLIANCE QUESTIONS ONLY: ISSUED BY: Crown Audio, Inc. 1.
CTs Power Amplifiers CTs Power Amplifiers Table of Contents CTs 4200 Maximum Average Power Dual in watts with 0.1% THD. 4 Channels Driven 1 kHz 20 Hz–20 kHz Important Safety Instructions ............2 5.1.5 AC Under-/Over-Voltage Protection ......14 4-ohm (per ch.) 260W 215W 8-ohm (per ch.)
CTs Power Amplifiers CTs Power Amplifiers 3 Setup 3 Setup 3.3 Ensure Proper Cooling 3.4 Choose Input Wire Figure 3.3 Balanced Input 3.1 Unpack Your Amplifier 3.2 Install Your Amplifier and Connectors Connector Wiring caUTiON: Before you begin, make sure When using an equipment rack, mount units Please unpack and inspect your amplifier for any damage that may have occurred during...
CTs Power Amplifiers CTs Power Amplifiers 3 Setup 3 Setup See the Crown Amplifier Appli cation Guide, available online at www.crownaudio.com, 3.6 Wire Your System 3.6.3 Bridge-Mono 16/8 Mode for pin assignments for See the Crown caUTiON: Never change the position of commonly used connector caUTiON: Never change the position of Amplifier Appli cation...
Page 6
CTs Power Amplifiers CTs Power Amplifiers 3 Setup 4 Operation 4. WaRNiNg: Never connect the output 3.7 Connect to AC Mains 3.8 Startup Procedure 4.1 Precautions to a power supply, battery or power Connect your amplifier to the AC mains power source Use the following procedure when first turning on Your amplifier is protected from internal and main.
Page 7
CTs Power Amplifiers CTs Power Amplifiers 4 Operation 4 Operation F. Fault indicator 4.3 Back Panel Controls 4.2 Front Panel Controls c. Signal indicator M. accessory Panel P. Mode Switch and Connectors and Indicators Green LED, one per channel, illuminates to CTs 4200: Accepts an optional IQ-MC4A or Used on each consecutive pair of channels, this Red LED, one per channel, illuminates...
Page 8
CTs Power Amplifiers CTs Power Amplifiers 5 Advanced Features 5 Advanced Features and Options and Options NOTe: For more information about these crown 5.1.4 35-Hz High-Pass Filter 5.2.4 Channel Level Control 5.2 Advanced Features aTTeNUaTiON in dB amplifier features, please visit the crown A fixed 35-Hz (70-Hz in CTs 4200) high-pass filter per The signal level for each input can be attenu ated 5.2.1 Switching Power Supply...
CTs Power Amplifiers CTs Power Amplifiers 5 Advanced Features 6 Troubleshooting and Options 5.3 Options choosing the Right Module CONDITION: Fault indicator is on. Wall-Mount level control panels for use with CONDITION: Power indicator is off. To order accessory modules for your amplifier, Vca module: Below are some available options.
CTs Power Amplifiers CTs Power Amplifiers 7 Specifications 6 Troubleshooting CTs 4200: MINIMUM GUARANTEED POWER (in watts, 0.1% THD) 120VAC, 60 Hz units Dual Mode CONDITION: No sound, even though CONDITION: Thermal indicator is Channels Driven the amp has power. Power LED is on flashing.
Page 11
CTs Power Amplifiers CTs Power Amplifiers 7 Specifications 7 Specifications The following specifications apply to all models in Dual 8/4 ohm mode with 8-ohm loads unless otherwise specified. Performance CTs 4200 CTs 8200 Frequency Response (at 1 watt, 20 Hz - 20 kHz) ±...
CTs Power Amplifiers CTs Power Amplifiers 7 Specifications 8 AC Power Draw and Thermal Dissipation AC Power Draw and Thermal Dissipation: Pink noise 12dB crest factor, bandwidth limited 22Hz to 22kHz. Typical line impedance used. Measurements made with 120VAC mains. Line current figures for 230VAC units derived by multiplying 120VAC figures by 0.5. Data based on all channels driven.
CTs Power Amplifiers CTs Power Amplifiers 8 AC Power Draw and 9 Service Thermal Dissipation Crown amplifiers are quality units that rarely require 5. Record the SRA number for future reference. The 2. Carefully place your product with the product’s front pack.
Page 14
CTs Power Amplifiers CTs Power Amplifiers 10 Warranty UNiTed STaTeS & caNada SUMMARY OF WARRANTY other encumbrances. The refund will be equal to ANY DEFECT IN THE NEW CROWN PRODUCT. the actual purchase price, not including inter est, THIS INCLUDES ANY DAMAGE TO ANOTHER Crown International, 1718 West Mishawaka Road, insurance, closing costs, and other finance PRODUCT OR PRODUCTS RESULT ING FROM...
Page 15
CTs Power Amplifiers CTs Power Amplifiers PROdUcT RegiSTRaTiON Crown Audio, Inc. 1718 W. Mishawaka Rd. NOTES Elkhart, IN 46517-9439 Phone: 574-294-8000 Fax: 574-294-8329 www.crownaudio.com Online registration is also available at http://crownweb.crownintl.com/webregistration. *Warranty is only valid within the United States of America. For information on Warranty outside of the U.S.A, please contact your local distributor. When this form is used to register your product, it may be mailed or faxed.
Page 16
CTs Power Amplifiers CTs Power Amplifiers Crown Audio Factory Service Information Shipping Address: Crown Audio Factory Service, 1718 W. Mishawaka Rd., Elkhart, IN 46517 PLEASE PRINT CLEARLY SRA #: __________________(If sending product to Crown factory service.) Model: ____________________________________________ Serial Number: _____________________ Purchase Date: _____________ PRODUCT RETURN INFORMATION Individual or Business Name: ____________________________________________________________________________________________________________________________________________________________...
Need help?
Do you have a question about the Crown CTs Series and is the answer not in the manual?
Questions and answers