Mitsubishi Electric Mr.SLIM SLZ-KF60VA Installation Manual page 9

7. Electrical work
1
C
B
A
2
D
Fig. 7-9
ON/OFF
MODE
CHECK
TEST RUN
SET
24
Fig. 7-11
ON/OFF
MODE
CHECK
TEST RUN
14
Fig. 7-12
MODEL SELECT
ON/OFF TEMP
FAN AUTO STOP
MODE VANE AUTO START
CHECK LOUVER h
TEST RUN min
SET RESET CLOCK
24
Fig. 7-10
B
MODEL SELECT
A
TEMP
3
FAN AUTO STOP
VANE AUTO START
LOUVER h
min
RESET CLOCK
A
MODEL SELECT
TEMP
3
FAN AUTO STOP
VANE AUTO START
LOUVER h
min
2
SET RESET CLOCK
7.3. Remote controller
7.3.1. Wired remote controller
1) Installing procedures
Refer to the installation manual that comes with each remote controller for details.
2) Function selection of remote controller
A
If two remote controllers are connected, set one to "Main" and the other to "Sub". For
setting procedures, refer to "Function selection of remote controller" in the operation
manual for the indoor unit.
3
7.3.2. For wireless remote controller
1) Installation area
• Area in which the remote controller is not exposed to direct sunshine.
• Area in which there is no nearby heating source.
• Area in which the remote controller is not exposed to cold (or hot) winds.
• Area in which the remote controller can be operated easily.
• Area in which the remote controller is beyond the reach of children.
2) Installation method (Fig. 7-9)
1 Attach the remote controller holder to the desired location using 2 tapping screws.
2 Place the lower end of the controller into the holder.
A Remote controller B Wall C Display panel D Receiver
• The signal can travel up to approximately 7 meters (in a straight line) within 45
degrees to both right and left of the center line of the receiver.
3) Setting (Fig. 7-10)
1 Insert batteries.
2 Press the SET button with something sharp at the end.
blinks and Model No. is lighted.
MODEL SELECT
buttons to set the Model No.
3 Press the temp
If you mistook the operation, press the ON/OFF
procedure 2.
4 Press the SET button with something sharp at the end.
and Model No. are lighted for 3 seconds, then turned off.
MODEL SELECT
Model No.
A
002
4) Automatic fan speed setting (For wireless remote controller)
It is necessary to set for wireless remote controller only when automatic fan speed
is not set at initial setting.
It is not necessary to set for wired remote controller with automatic fan speed at
initial setting.
1 Press the SET button with something sharp at the end.
Operate when display of remote controller is off.
blinks and Model No. is lighted A.
MODEL SELECT
2 Press the AUTO STOP
blinks and setting No. is lighted B.
(Setting No.01: without automatic fan speed)
buttons to set the setting No.02.
3 Press the temp.
(Setting No.02:with automatic fan speed)
If you mistook the operation, press the ON/OFF
procedure 2.
4 Press the SET button with something sharp at the end.
and Model No. are lighted for 3 seconds, then turned off.
MODEL SELECT
5) Assigning a remote controller to each unit (Fig. 7-12)
Each unit can be operated only by the assigned remote controller.
Make sure each pair of an indoor unit PC board and a remote controller is assigned
to the same pair No.
6) Wireless remote controller pair number setting operation
1 Press the SET button with something sharp at the end.
Start this operation from the status of remote controller display turned off.
blinks and Model No. is lighted.
MODEL SELECT
2 Press the min button twice continuously. Pair No. "0" blinks.
3 Press the temp buttons to set the pair number you want to set.
If you mistook the operation, press the ON/OFF
from procedure 2.
4 Press the SET button with something sharp at the end.
Set pair number is lighted for 3 seconds then turned off.
A Pair No. of wireless remote controller
3-9
button and operate again from
button.
button and operate again from
button and operate again
Indoor PC board
0 Initial setting
1 Cut J41
2 Cut J42
Cut J41, J42
9