Electrolux PD91-ANIMT Instruction Book page 5

ENGLISH
Thank you for choosing Electrolux PURED9 vacuum cleaner. Always
use original accessories and spare parts to get the best results. This
product is designed with the environment in mind. All plastic parts
are marked for recycling purposes.
BEFORE STARTING
• Read this manual carefully.
• Check that all parts described are included.
• Pay special attention to the safety precautions!
DESCRIPTION OF PURED9 VACUUM CLEANER
A. Display (see versions later)
B. Exhaust filter lid
C. Exhaust filter
D. Parking slots
E. Power cord
F. Motor filter
G. Motor filter holder
H. S-bag®
I. S-bag® holder
J. Dust compartment cover
K. AeroPro 3in1 tool
L. AeroPro hose
M. AeroPro handle (see versions
later)
N. AeroPro telescopic tube
O. Parking clip
P. Display for models with rotary
knob manual control*
HOW TO USE THE VACUUM CLEANER
1
Open the dust compartment cover by pulling the S-BAG button.
Check that the dust bag (s-bag) is in place.
2
Insert the hose into the cleaner (to remove it, press the lock buttons
and pull). Insert the hose into the hose handle until the lock button
clicks (to release it, press the lock button and pull).
3
Attach the telescopic tube to the nozzle. Attach the telescopic tube to
the hose handle (to remove it, press the lock button and pull).
4
Adjust the telescopic tube by holding the lock with one hand and
pulling the handle with the other hand.
START/STOP THE VACUUM CLEANER AND ADJUST SUCTION POWER
5
Pull out the power cord and plug it into the mains. Press the ON/
OFF button to turn the cleaner on/off. Indicators light up, MIN/MAX
indicator lights up from left to right and back (auto function models).*
Models with remote control can also be operated by the ON/OFF
button on the handle.*
6
Adjust suction power (manual control models): Turn the rotary knob
on the cleaner or use the air valve on the handle.*
7
Adjust suction power (remote control models): Press +/- button on the
handle. MIN/MAX and symbols indicators on display will show level of
power.*
8
Adjust suction power (remote control models with AUTO): The cleaner
starts in AUTO mode (automatic power regulation). AUTO indicator is
illuminated on the display and MIN/MAX indicator pulses. To regulate
power manually press +/- button on handle. Press AUTO button to
return to auto-function.*
9
After cleaning, push the REWIND button to rewind the cable.
PARKING POSITIONS
10
Use parking position on the side (A) or underneath (C) to carry and
store the cleaner. At the back (B) when you pause (save your back).
REPLACING THE DUSTBAG, S-BAG®
11
Replace the s-bag when
- P* Models with rotary knob: S-BAG indicator lights up in red
- Q* Models with remote control: S-BAG symbol lights up red.
- R* Models with remote control and AUTO: S-BAG indicator lights
up in red (green light: bag is OK, yellow light: soon time to replace
bag).
NB: Always change the s-bag when S-BAG indicator is illuminated or
www.electrolux.com
Q. Display for models with remote
control*
R. Display for models with remote
control and AUTO function*
S. AeroPro Classic handle*
T. AeroPro Ergo handle*
U. AeroPro Remote Control
handle*
V. FlowMotion nozzle*
W. FlowMotion LED nozzle (with
front lights)*
X. AeroPro Turbo nozzle*
Y. AeroPro Mini Turbo nozzle*
Z. ParkettoPro nozzle*
AA. AeroPro FlexProPlus nozzle*
AB. AeroPro Long crevice nozzle*
* Certain models only
has red light even if the s-bag is not full (it may be blocked) and after
using carpet cleaning powder. For best possible performance, use the
Ultra Long Performance bag which is especially developed for your
cleaner. Other synthetic s-bags can also be used. Do not use paper
dust bags! www.s-bag.com
12
Pull the S-BAG button to open the dust compartment. The handle of
the s-bag holder goes up. Pull the handle to remove the s-bag with
holder. Do not press the release button.
13
Hold the s-bag with holder over a dust bin. Press the button to release
the s-bag. Insert a new s-bag to the holder by inserting the cardboard
at the back of the holder.
14
Insert the s-bag with holder by pushing it straight down in its tracks.
Make sure the s-bag is not stuck under the holder. Close the lid. If the
s-bag is not properly placed or is missing, the lid will not close.
NB: When you start the cleaner after s-bag replacement, It takes 10
seconds before the S-BAG indicator turns off (P* Models with rotary
knob and Q* Models with remote control) or turns green (R* Models
with remote control and AUTO).
REPLACING THE FILTERS
15
Replace/clean** the filter when (**washable filter only)
- P* Models with rotary knob: you have changed the s-bag 5 times
- Q* Models with remote control: FILTER symbol lights up in red
- R* Models with remote control and AUTO: filter indicator lights
up in red. Green light indicates that the filter is ok. It lights up briefly
when you start the vacuum cleaner.
16
Pull the FILTER button to open the filter lid. Use original s-filters.
Remove the filter and check the reference on the frame to define type.
Replace with a new filter or clean it**. Rinse the inside (dirty side) in
lukewarm tap water. Tap the filter frame to remove the water. Repeat
the process four times. (* *washable filter only)
NB: Do not use cleaning agents. Avoid touching the filter surface.
Let the filter dry completely (min. 24 h in room temperature) before
putting back ! Change the washable filter at least once a year or when
it is very dirty or damaged. Do not remove the L-shaped foam under
the filter.
17
After replacing the filter, close the filter lid until it is clicked back into
place. If the filter lid comes off, position the hinges at the bottom and
push the filter lid until it is clicked back into place.
NB: When you start the cleaner after filter replacement, It takes 10
seconds before the FILTER indicator turns green (models with remote
control and AUTO function) or turns off (remote control models).*
18
Replace the motor filter when dirty or after every 5th s-bag. Push the
filter holder down and pull it out. Exchange the filter and close the lid.
VACUUMING WITH THE UNIVERSAL NOZZLE (V*, W*)
19
Change nozzle setting with the pedal. Icon illustrates recommended
floor type.
20
FlowMotion LED nozzle*: Move the nozzle forward. The front light
turns on automatically after a few seconds. When the nozzle is not
used, the light turns off automatically after a few seconds.
CLEANING THE UNIVERSAL NOZZLE (V*, W**)
21
Disconnect the nozzle from the tube. Clean with the hose handle.
CLEANING THE TURBO NOZZLE (X*)
22
Disconnect the nozzle from the tube and remove entangled threads
etc by snipping them away with scissors. Use the hose handle to clean
the nozzle. *
3IN1 ACCESSORY TOOL
23
Pull the textile tab to take out 3in1 tool. The tool has 3 functions, see
pictures on next page.
24
After usage, put it back in its place.
TR
GB
UA
AR
RU
FR
DE
7