Automatic Timer; Kitchen Timer; Power Manager; Automatic Safety Cut-Out - Siemens ET9 FKB1Q Series Instruction Manual

The cooking time counts down. If you have set a
cooking time for more than one hotplate, the cooking
time of the selected hotplate is always displayed.
Automatic setting
If you touch settings range presets 1 to 5 for a longer
time, the cooking time automatically counts back down
to one minute.
If you touch settings range presets 6 to 10 for a longer
time, the cooking time automatically counts up to 99
minutes.
When the cooking time has elapsed
When the cooking time has elapsed, the hotplate
switches off. You will hear a signal and
the display for 10 seconds. The
brightly. Touch the symbol. The displays go out and
0
the audible signal ceases.
Changing or cancelling the cooking time
Select the hotplate and touch the
display lights up brightly. Change the cooking time or
set to in the settings range.
‹‹
You can set a cooking time of up to 99 minutes.
Note:

Automatic timer

You can use this function to preselect a cooking time
for all hotplates. Each time a hotplate is switched on,
the pre-selected cooking time then counts down. When
the cooking time has elapsed, the hotplate switches off
automatically.
You can find out how to switch on the automatic timer in
the Basic settings section.~ Page 10
You can change the cooking time for a hotplate
Note:
or switch off the automatic timer for the hotplates.
Select the hotplate and touch the
desired display lights up brightly. Change the
x
cooking time or set to
‹‹

Kitchen timer

You can use the kitchen timer to set a time of up to 99
minutes. It runs independently of all the other settings.
Switching on the kitchen timer
You can switch the kitchen timer on in 2 different ways:
If a hotplate has been selected, touch the
■
twice within 10 seconds.
If a hotplate has not been selected, touch the
■
symbol.
The display lights up.
V
Setting the kitchen timer
Set the desired time in the control panel.
lights up in
‹‹
indicator lights up
x
symbol. The
0
symbol. The
0
in the settings range.
0 symbol
0
After the time has elapsed
After the time has elapsed, you will hear a beep.
lights up in the timer display. The
kitchen timer lights up brightly. The display switches off
after 10 seconds.
Displaying the time
Use the 0
is displayed for 10 seconds.
Setting the correct time
Use the
0
the time.
hPower manager
The power manager limits the maximum power
P o w e r m a n a g e r
x
consumption of the appliance to 7000 watts.
If you switch on a hotplate and the power limit is
reached, - appears briefly on the heat setting display.
The appliance is automatically regulated to the highest
possible heat setting.
bAutomatic safety cut-out
If a hotplate has been switched on for a long time
c u t - o u t A u t o m a t i c s a f e t y
without the setting being changed, the automatic time
limit is activated.
The hotplate stops heating.
heat indicator flash alternately on the hotplate display.
The display goes out when you touch any control. You
can make new settings.
When the time limit is activated depends on the heat
setting selected (1 to 10 hours).
kWipe protection
If you wipe over the control panel while the hob is
W i p e p r o t e c t i o n
switched on, settings may be changed.
To prevent this from happening, your hob has a wipe
protection function. Touch the symbol
goes off. The display light above the
lights up. The control panel is locked for 30 seconds.
You can now wipe over the control panel without
changing any settings.
The primary switch is not affected by the wipe
Note:
protection function. You can switch off the hob at any
time.

Power manager

V
symbol to select the kitchen timer. The time
symbol to select the kitchen timer and reset
and the
"‰
en
‹‹
display for the
/ residual
• œ
‚ / $ . A beep
/ symbol
‚ $
9