Stagg 10 GA USA User Manual

1 2 3 4 5

FRONT PANEL:

1. INPUT: Plug your guitar in here. We recommend that you always use a high-quality shielded guitar
cable to prevent any background noise interference or unwanted feedback.
2. GAIN: This control determines the distortion intensity of the amplifier's overdrive setting. Adding GAIN
will make your guitar sound more distorted.
3. OVERDRIVE: This switch activates the amplifier's built-in overdrive function, which adds distortion to
the signal.
4. VOLUME: This control determines the output volume of the amplifier.
5. TREBLE: This control determines the level of high frequencies in the output signal. Adding TREBLE will
make your guitar sound brighter and sharper.
6. MID: This control determines the level of middle frequencies in the output signal. Adding MID will make
your guitar sound rounder and fuller. As this control is PARAMETRIC, it also allows you to vary the central
frequency of the midrange. When turned to the left, it will add low-mid and cut upper-mid. As you turn the
control to the right, you will increase the upper-mid presence, while cutting the low.
7. BASS: This control determines the level of low frequencies in the output signal. Adding BASS will make
your guitar sound warmer and heavier.
8. HEADPHONES: This is a 1/8" (Ø 3.5 mm) mini-jack ( 10 GA model) or a 1/4" (Ø 6.3 mm) standard
jack ( 10 GA P model) output to connect the headphones. When headphones are connected, no sound is
produced from the speaker.
9. CD/MP3 INPUT: For 10 GA model only, this is a line level 1/8" (Ø 3,5 mm) stereo mini jack into which
an MP3/CD/Tape player may be connected.
10. POWER LED: When this red LED is lit, the amplifier is ready to work. When it is off, it means the
amplifier is powered off.
11. POWER: This switch turns the amplifier on or off.
2
USER'S MANUAL
6 7 8 9 10 1 1
10 GA USA & 10 GA P USA

BACK PANEL:

WARNING: This amplifier must be earthed. Please check that the supply voltage details given on the
rating label (located on the rear panel) are in accordance with your electricity supply.
1 POWER FUSE: In case the power fuse has to be replaced, first unplug the power cable from the mains
outlet. Then remove the fuse cover and replace the power fuse with one of the same type and value. Never
plug the power cable back into the mains outlet without the fuse cover. When powering on the amplifier,
if the power fuse blows up again, go to a suitable service centre for repair.
MAINS CABLE: This amplifier features a power cable with a moulded-on plug. If the socket outlets in
the home are not suitable for the plug supplied with this amplifier, use an appropriate plug adapter that
can handle the power required for this amplifier.
In case the power cable or plug is damaged, unplug it in a safe way from the mains outlet and go to a
suitable service centre for replacement.

TECHNICAL SPECIFICATIONS

Max. Rated Power / Loudspeaker
Frequency Response
Total Harmonic Distortion
Signal to Noise Ratio
Input Impedance
Power Consumption
Maximum Input Level
Maximum Gain
Dimensions (H x W x D)
Weight
Features and Specifications are subject to change without notice.
10 GA USA & 10 GA P USA
INPUT: ~110V/60Hz FUSE: T1AH/250V
PWR: 16W
DATE:
1
10 Watts RMS @ 8 Ohms load / 6.5" Speaker
70 Hz to 10 kHz
0.8% (Clean Mode)
- 60 dB @ max Rated Power
470k Ohms
20 Watts max
40 mV (RMS)
44 dB (@ 1kHz)
29 x 28 x 18 cm / 11.4 x 11 x 7.1 in
4.3 kg / 9.5 lb
3
USER'S MANUAL
CM
C US
CONFORMS TO
UL STD. 60065
CERTIFIED TO
CAN/CSA STD.
C22.2 No.60065:03