Related Manuals for Case IH PUMA 115
Summary of Contents for Case IH PUMA 115
- Page 1 PUMA 115 PUMA 125 PUMA 140 PUMA 155 Tractor with/without Multicontroller SERVICE MANUAL Part number 87727132BNA English December 2010 Replaces part number 87727132...
- Page 2 SERVICE MANUAL PUMA 115 , PUMA 125 Multicontroller , PUMA 125 , PUMA 140 Multicontroller , PUMA 140 , PUMA 155 Multicontroller , PUMA 155 87727132B 13/04/2010...
- Page 3 Contents INTRODUCTION HYDRAULIC - PNEUMATIC - ELECTRICAL - ELECTRONIC SYSTEMSA PRIMARY HYDRAULIC POWER SYSTEM ..........A.10.A PRIMARY HYDRAULIC POWER SYSTEM Closed center mechanical remote valve .
- Page 4 STEERING Hydraulic..............D.20.C STEERING AutoPilot .
- Page 5 87727132B 13/04/2010...
- Page 6 INTRODUCTION 87727132B 13/04/2010...
- Page 7 Contents INTRODUCTION Foreword ..................3 Safety rules .
- Page 8 INTRODUCTION Foreword Technical Information This manual has been produced by a new technical information system. This new system is designed to deliver technical information electronically through CD-ROM and in paper manuals. A coding system called ICE has been developed to link the technical information to other Product Support functions e.g. Warranty. Technical information is written to support the maintenance and service of the functions or systems on a customers machine.
- Page 9 INTRODUCTION How to Use this Manual This manual is divided into Sections. Each Section is then divided into Chapters. Contents pages are included at the beginning of the manual, then inside every Section and inside every Chapter. An alphabetical Index is included at the end of a Chapter.
- Page 10 INTRODUCTION This manual contains these Sections. The contents of each Section are explained over the following pages. Contents INTRODUCTION DISTRIBUTION SYSTEMS POWER PRODUCTION POWER TRAIN TRAVELLING BODY AND STRUCTURE TOOL POSITIONING CROP PROCESSING Section Contents SECTION A, DISTRIBUTION SYSTEMS This Section covers the main systems that interact with most of the functions of the product. It includes the central parts of the hydraulic, electrical, electronic, pneumatic, lighting and grease lubrication systems.
- Page 11 INTRODUCTION Chapters Each Chapter is identified by a letter and number combination e.g. Engine B.10.A The first letter is identical to the Section letter i.e. Chapter B.10 is inside Section B, Power Production. CONTENTS The Chapter Contents lists all the technical data (specifications), functional data (how it works), service data (remove, install adjust, etc..) and diagnostic data (fault codes and troubleshooting) that have been written in that Chapter for that function or system on the machine.
- Page 12 INTRODUCTION Information Units and Information Search Each chapter is composed of information units. Each information unit has the ICE code shown in parentheses which indicates the function and the type of information written in that information unit. Each information unit has a page ref- erence within that Chapter.
- Page 13 INTRODUCTION Important information All repair and maintenance works listed in this manual must be carried out only by staff belonging to the Case I H Service network, strictly complying with the instructions given and using, whenever required, the special tools. Anyone who carries out the above operations without complying with the prescriptions shall be responsible for the subsequent damages.
- Page 14 INTRODUCTION Safety rules IMPORTANT NOTICE All maintenance and repair operations described in this manual should be carried out exclusively by authorised work- shops. All instructions should be carefully observed and special equipment where indicated should be used. Anyone who carries out service operations described without carefully observing these instructions will be directly responsible for any damage caused.
- Page 15 INTRODUCTION Do not wear rings, wristwatches, jewels, unbuttoned or flapping clothing such as ties, torn clothes, scarves, open • jackets or shirts with open zips which could get caught on moving parts. Use approved safety clothing such as anti-slipping footwear, gloves, safety goggles, helmets, etc. Wear safety glasses with side guards when cleaning parts using compressed air.
-
Page 16: Table Of Contents
INTRODUCTION charging, leave the battery compartment uncovered to improve ventilation. Avoid sparks or flames near the battery area. Do no smoke. Do not charge batteries in confined spaces. • Always disconnect the batteries before performing any type of service on the electrical system. •... -
Page 17: Health And Safety Precautions
INTRODUCTION FUELS - see Fire, Legal Aspects, Chemicals - General, Solvents....GAS CYLINDERS - see Fire......... . GENERAL WORKSHOP TOOLS AND EQUIPMENT. -
Page 18: Acids And Alkalis
INTRODUCTION Skin and eye contact should be avoided and the manufacturers instructions followed. Cyanoacrylate adhesives (super-glues) must not contact the skin or eyes. If skin or eye tissue is bonded cover with a clean moist pad and get medical attention. do not attempt to pull tissue apart. Use in well ventilated areas as vapours can cause irritation of the nose and eyes. -
Page 19: Brake And Clutch Fluids (Polyalkylene Glycols) - See Fire
INTRODUCTION Do organise work practices and protective clothing to avoid soiling of the skin and eyes; breathing vapours/aerosols/ dusts/fumes; inadequate container labelling; fire and explosion hazards. Do wash before job breaks; before eating, smoking, drinking or using toilet facilities when handling chemical materials. Do keep work areas clean, uncluttered and free of spills. -
Page 20: Exhaust Fumes
INTRODUCTION Ensure that the cables of mobile electrical equipment cannot get trapped and damaged, such as in a vehicle hoist. Use air operated mobile equipment where possible in preference to electrical equipment. In cases of electrocution:- switch off electricity before approaching victim •... -
Page 21: Fuels - See Fire, Legal Aspects, Chemicals - General, Solvents
INTRODUCTION Individuals with chronic respiratory diseases, asthma, bronchial medical problems or histories of allergic diseases should not work with or near uncured materials. The components, vapours, spray mists can cause direct irritation, sensitivity reactions and may be toxic or harmful. Vapours and spray mists must not be breathed. -
Page 22: General Workshop Tools And Equipment
INTRODUCTION Gases see Gas Cylinders. Gas Shielded Welding see Welding. Gas Welding see Welding. GENERAL WORKSHOP TOOLS AND EQUIPMENT It is essential that all tools and equipment are maintained in good condition and the correct safety equipment used where required. Never use tools or equipment for any purpose other than that for which they were designed. -
Page 23: Paints - See Solvents And Chemical Materials - General
INTRODUCTION PAINTS see Solvents and Chemical Materials - General. Highly Flammable, Flammable. One Pack. Can contain harmful or toxic pigments, driers and other components as well as solvents. Spraying should only be carried out with adequate ventilation. Two Pack. Can also contain harmful and toxic unreacted resins and resin hardening agents. The manufacturers instructions should be followed and the section of page 5 on resin based adhesives, isocyanate containing Adhesives and Foams should be consulted. -
Page 24: Suspended Loads
INTRODUCTION Avoid splashes to the skin, eyes and clothing. Wear protective gloves, goggles and clothing if necessary. Ensure good ventilation when in use, avoid breathing fumes, vapours and spray mists and keep containers tightly sealed. Do not use in confined spaces. When the spraying material contains solvents, e.g.