Cloos GLW 222 AC/DC Operating Instructions And Spare Parts
  1. Manuals
  2. Brands
  3. Cloos Manuals
  4. Inverter
  5. GLW 222 AC/DC
  6. Operating instructions and spare parts

Cloos GLW 222 AC/DC Operating Instructions And Spare Parts

Portable inverter
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Operating
instructions and
Spare parts
GLW 222 AC/DC
Portable Inverter
- EN -
Rev.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GLW 222 AC/DC and is the answer not in the manual?

Questions and answers

Related Manuals for Cloos GLW 222 AC/DC

Summary of Contents for Cloos GLW 222 AC/DC

  • Page 1 Operating instructions and Spare parts GLW 222 AC/DC Portable Inverter - EN - Rev.1...
  • Page 2 Carl Cloos Schweisstechnik GmbH Industriestrasse 35708 Haiger Germany Telephone: (0 27 73) 85-0 Telefax: (0 27 73) 85-275 E-Mail: info@cloos.de Internet: http://www.cloos.de RW - FP - Rev.0 release date: 10.12.15 Keep for further use.
  • Page 3 Hiermit erklären wir, dass das nachfolgend aufgeführte Gerät in Übereinstimmung mit den EU-Richtlinien entwickelt, konstruiert und gefertigt sowie in den Verkehr gebracht wurde. Bezeichnung des Gerätes: WIG Schweissgerät Typbezeichnung: QINEO GLW 222 AC/DC Fabriknummer: siehe Typenschild (Geräterückseite) Folgende EG-Richtlinien sind angewandt: - EG-Niederspannungsrichtlinie (2006/95/EG) - EG-Richtlinie Elektromagnetische Verträglichkeit (2004/108/EG)
  • Page 4 RESET (LOAD FACTORY SETTINGS) ........9 SPARE PARTS ..............28 PARTIAL RESET ..............9 ELECTRICAL DIAGRAM ............. 30 TOTAL RESET ..............10 16.1 GLW 222 AC/DC ..............30 SET-UP (INITIAL SET-UP OF THE WELDING POWER 16.2 TORCH CONNECTOR ............31 SOURCE) ................10 16.3 REMOTE CONTROLLER CONNECTOR ......

  • Page 5: Front Panel

    This symbol accompanies important information concerning the execution of the relevant operations. GLW 222 AC/DC is an advanced technology single-phase welding power source for AC and DC TIG welding operations. AC TIG functions are ideal for aluminum, magnesium and related alloys welding.

  • Page 6: Rear Panel

    Cod.006.0001.1481 GLW 222 AC/DC 14/05/2014 v2.4 ENGLISH REAR PANEL PREPARING FOR MMA WELDING 1. Set the welding power source ON/OFF switch to “O” (unit de- energized). 2. Plug the power cable plug into a mains socket outlet. 1: Welding power source ON/OFF switch.
  • Page 7 Cod.006.0001.1481 14/05/2014 v2.4 GLW 222 AC/DC ENGLISH PREPARING FOR TIG WELDING Installation with cooling unit 1. Set the welding power source ON/OFF switch to “O” (unit de- energized). 2. Remove the screws from the power source cabinet. 9. Connect the gas hose from the welding gas cylinder to the rear gas socket.
  • Page 8 Cod.006.0001.1481 GLW 222 AC/DC 14/05/2014 v2.4 ENGLISH welding arc. 20. Use the flow control valve to adjust the flow of gas as required while the gas is flowing out. 21. Set the required welding parameter values on the user interface.

  • Page 9: User Interface

    Cod.006.0001.1481 14/05/2014 v2.4 GLW 222 AC/DC ENGLISH USER INTERFACE CODE SYMBOL DESCRIPTION DC TIG mode: Illumination shows that the following function has been activated: Q-START AC TIG mode: Illumination shows that the following function has been activated: AC WAVE IN MIX AC-DC...

  • Page 10: Unit Power-Up

    Cod.006.0001.1481 GLW 222 AC/DC 14/05/2014 v2.4 ENGLISH Data setting: The display shows the various welding menus relative to the selected processes. The display shows the selected parameter. AC TIG mode: Press the button to select the parameter to be set. Possible choices:...

  • Page 11: Set-Up (Initial Set-Up Of The Welding Power Source)

    Cod.006.0001.1481 14/05/2014 v2.4 GLW 222 AC/DC ENGLISH TOTAL RESET The reset procedure involves complete restoration of the default values, parameters and memory settings set in the factory. All memory locations will be reset and hence all your personal welding settings will be lost! Set the welding power source ON/OFF switch to “O”...
  • Page 12 Cod.006.0001.1481 GLW 222 AC/DC 14/05/2014 v2.4 ENGLISH Cooler activation  ON= The cooler is always running when the power source is switched on. This mode is preferable for heavy duty and automatic welding procedures.  OFF= The cooler is always disabled because an air-cooled torch is in use.

  • Page 13: Torch Loading

    Cod.006.0001.1481 14/05/2014 v2.4 GLW 222 AC/DC ENGLISH TORCH LOADING WARNING! Make sure the torch in use is correctly sized in relation to the welding current required and for the available and selected cooling type. This prevents the risk of burns to which the operator is potentially exposed, potential faults, and irreversible damage to the torch and the system.

  • Page 14: Welding Parameters

    Cod.006.0001.1481 GLW 222 AC/DC 14/05/2014 v2.4 ENGLISH WELDING PARAMETERS For a better understanding of the parameter functions described in the table, refer to the following diagram. (I1) TIG WELDING CURRENT (I2) BASE CURRENT (I3) FINAL CURRENT (I4) STARTING CURRENT (t1) UP SLOPE TIME...
  • Page 15 Cod.006.0001.1481 14/05/2014 v2.4 GLW 222 AC/DC ENGLISH Peak time Spot TIG time Time for which the current pulse is at the maximum value. When the torch trigger is pressed the welding arc persists for the time set in the parameter.
  • Page 16 Cod.006.0001.1481 GLW 222 AC/DC 14/05/2014 v2.4 ENGLISH The following picture shows the positive wave interval ΔI that, if subtracted and added to the negative wave, forms the new form of broken line wave. Consequences of a higher value:  Greater weld penetration.
  • Page 17 Cod.006.0001.1481 14/05/2014 v2.4 GLW 222 AC/DC ENGLISH 16/34...
  • Page 18 Cod.006.0001.1481 GLW 222 AC/DC 14/05/2014 v2.4 ENGLISH 17/34...

  • Page 19: Welding Settings

    Cod.006.0001.1481 14/05/2014 v2.4 GLW 222 AC/DC ENGLISH WELDING SETTINGS 11.1 ELECTRODE WELDING (MMA) This button serves to select the following welding mode: 11.1.1 MMA PARAMETERS SETTING (1ST LEVEL) Press this button to scroll the list of settings to edit. The selected parameter and its value are shown on the following displays: D2 Using the encoder, edit the value of the selected setting.
  • Page 20 Cod.006.0001.1481 GLW 222 AC/DC 14/05/2014 v2.4 ENGLISH Tab. 5 - Special functions in MMA mode PARAMETER DEFAULT DYNAMIC ARC 11.2 DC TIG WELDING Use this button to select one of the following welding modes: DC TIG PULSED DC TIG SYNERGIC PULSED DC TIG...
  • Page 21 Cod.006.0001.1481 14/05/2014 v2.4 GLW 222 AC/DC ENGLISH PARAMETER DEFAULT SPOT TIG TIME 0.01 s 0.1 s 10.0 s HF ARC START REMOTE CONTROL MINIMUM PEDAL CURRENT 50 % 90 % *1: The activation is suitable for the following welding modes: ...
  • Page 22 Cod.006.0001.1481 GLW 222 AC/DC 14/05/2014 v2.4 ENGLISH 11.3 AC TIG WELDING Use this button to select one of the following welding modes: AC TIG PULSED AC TIG Use this button to select one of the following torch trigger procedures: 2 STEP 2T SPOT 4 STEP 4 STEP BI-LEVEL 11.3.1 AC TIG PARAMETERS SETTING (1ST LEVEL)
  • Page 23 Cod.006.0001.1481 14/05/2014 v2.4 GLW 222 AC/DC ENGLISH Tab. 10 - 2nd level menu parameters in AC TIG mode PARAMETER MIN DEFAULT MAX SPOT TIG TIME 0.01 s 0.1 s 10.0 s REMOTE CONTROL ON *1 MINIMUM PEDAL CURRENT 1 %...

  • Page 24: Jobs Management

    Cod.006.0001.1481 GLW 222 AC/DC 14/05/2014 v2.4 ENGLISH JOBS MANAGEMENT Personalised welding settings, or JOBs, can be saved in memory locations and subsequently uploaded. Up to 50 jobs can be saved (j01-j50). The settings of the SETUP menu are not saved.

  • Page 25: Torch Trigger Modes

    Cod.006.0001.1481 14/05/2014 v2.4 GLW 222 AC/DC ENGLISH NO STORED JOB The message appears only if there are saved JOBS, on the following displays: D2 Use the encoder to select the number of the job to be deleted. Exit without confirmation Press any button (except S2).

  • Page 26: Spot Welding

    Cod.006.0001.1481 GLW 222 AC/DC 14/05/2014 v2.4 ENGLISH 13.4 4T HF WELDING 1. Bring the torch up to the work until the electrode tip is approximately 2 or 3 mm away. 2. Press (1T) and release (2T) the torch trigger. The arc strikes without contact with the workpiece and the voltage discharges (HF) cease automatically.
  • Page 27 Cod.006.0001.1481 14/05/2014 v2.4 GLW 222 AC/DC ENGLISH 13.8 2T SPOT HF WELDING 1. Bring the torch up to the work until the electrode tip is approximately 2 or 3 mm away. 2. Press (1T) the torch trigger. The arc strikes without contact with the workpiece and the voltage discharges (HF) cease automatically.

  • Page 28: Technical Data

    Cod.006.0001.1481 GLW 222 AC/DC 14/05/2014 v2.4 ENGLISH TECHNICAL DATA Model GLW 222 AC/DC EN 60974-1 Construction standards EN 60974-3 EN 60974-10 Class A Supply voltage 1 x 230V ~± 15 % / 50-60 Hz Mains protection 25 A Delayed Dimensions ( L x D x H )
  • Page 29 Cod.006.0001.1481 14/05/2014 v2.4 GLW 222 AC/DC ENGLISH Spare parts list Item. Part No. Designation 0835 22 00 01 BELT 0835 22 00 02 UPPER COVER 0835 22 00 03 HF BOARD 0835 21 00 41 PRIMARY RECTIFIER 0835 21 00 03...
  • Page 30 Cod.006.0001.1481 GLW 222 AC/DC 14/05/2014 v2.4 ENGLISH Item. Part No. Designation 0835 21 00 17 TRANSFORMER SUPPORT 0835 22 00 08 RUBBER FOOT 0835 21 00 22 LOWER COVER 0835 21 00 18 HALL SENSOR 0535 22 00 09 DIODE...
  • Page 31 Cod.006.0001.1481 GLW 222 AC/DC 14/05/2014 v2.4 ENGLISH 14.2 Cooling unit FC 10...
  • Page 32 Cod.006.0001.1481 GLW 222 AC/DC 14/05/2014 v2.4 ENGLISH Pos. / Artikelnummer / Bezeichnung Designation Item Part No. 0835 20 05 50 Schnellkupplung 1/8 Gas QUICK CLUTCH 1/8 GAS 0835 20 05 51 Reduziernippel I=1/8 A=1/8 F=1/8 - M=1/8 NIPPLE CONNECTOR 0835 20 05 52...
  • Page 33 Cod.006.0001.1481 GLW 222 AC/DC 14/05/2014 v2.4 ENGLISH Item. Part No. Designation 0835 20 05 00 Cooling unit CU-05C 0835 20 01 00 Trolley 02 0835 20 04 00 Overcut (Generator protection) 0831 90 03 35 Electrode holder 35mm2 L=4m 0831 90 02 40...

  • Page 34: Torch Connector

    Cod.006.0001.1481 GLW 222 AC/DC 14/05/2014 v2.4 ENGLISH 16.2 TORCH CONNECTOR 16.3 REMOTE CONTROLLER CONNECTOR Torch Torch with potentiometer Up & down torch 2 kOhm - 10 kOhm potentiometer Remote controller 2 kOhm - 10 kOhm potentiometer Foot pedal controller 2 kOhm - 10 kOhm potentiometer...
  • Page 35 Cod.006.0001.1481 14/05/2014 v2.4 GLW 222 AC/DC ENGLISH 34/34...

Table of Contents