Related Manuals for Toro Versa Vac 07053
Summary of Contents for Toro Versa Vac 07053
- Page 1 Form No. 3364–827 Rev. A Versa Vac Model No. 07053—Serial No. 310000001 and Up Operator’s Manual English (EN)
-
Page 2: Table Of Contents
Check Torque Of Wheel Nuts ....Dealer or Toro Customer Service and have the model and Operation ........ -
Page 3: Safety
A free replacement manual is available by sending the • Never operate the machine when under the influence of complete Model and Serial Number to The Toro drugs or alcohol. Company, 8111 Lyndale Avenue South, Bloomington, •... - Page 4 Stay clear of trailer while machine is purchase genuine Toro replacement parts and backing up or dumping. accessories to keep the machine all Toro. Never use • Keep bystanders a safe distance from trailer when “will-fit” replacement parts and accessories made by operating to dump debris or when opening and closing other manufacturers.
-
Page 5: Safety And Instruction Decals
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 105-0627 1. Warning—stop the engine and remove the ignition key before getting off of the tractor;... - Page 6 93-6674 1. Crushing hazard, hand—read the instructions before servicing or performing maintenance. 106-0163 1. Warning—read the Operator’s Manual and receive training. The maximum load is 1350 lb. (612 kg) trailer weight and 850 lb (385 kg) tongue weight. Do not drive the machine and trailer down hill or you may lose control.
- Page 7 106-0167 1. Warning—read the Operator’s Manual and receive training. 106-0166 Stop the engine and remove the ignition key before getting off of the tractor; read the instructions before servicing or 1. Warning—read the Operator’s Manual and receive training. performing maintenance, then connect or disconnect the Stop the engine and remove the ignition key before getting off hydraulic hoses.
-
Page 8: Specifications
Specifications General Specifications Width: 78 inches. Height: 83 inches. Overall Dimensions Length: 185 inches. Weight: 2294 lb. (1040 kg) Note: Specifications and design subject to change without notice. -
Page 9: Setup
Setup Note: Use this chart as a checklist to ensure that all parts have been received. Without these parts, total setup cannot be completed. Description Qty. Drive Shaft Mount drive shaft blower and tractor Canvas Ring Mount to Versa Vac and attachment Install control lever only if Combination Deck is Auxiliary Control Lever installed. -
Page 10: Adjusting The Pto Shaft Length
4. Use the following calculation to establish how much shorter the shaft must be, when connected, to ensure a clearance of 1-1/2 inches (37 mm): A. Subtract the dimension recorded in step 2 from the dimension recorded in step 1. Record this dimension. -
Page 11: Removing The Versa Vac From The Tractor
Caution Before leaving the operator’s seat on the tractor, wait for the engine and all moving parts to stop. 4. Block the wheels. 5. Disconnect the safety shield chains from the tractor or PTO shield. Secure the end of the chain to the impeller side of the PTO shaft to prevent the PTO shaft from coming apart. -
Page 12: Before Operating
One bottle is sufficient for 4–6 gal (15–22 1) of hydraulic (115–136 NVm) after 1–4 hours of operation and oil. Order part no. 44–2500 from your authorized Toro again after 10 hours of operation. Torque every distributor. Not recommended for biodegradable fluid (use food coloring). -
Page 13: Operation
Operation Auxiliary Control Used to operate Combination Deck, Model 07082. Up position starts the deck and down position stops the deck. Note: Determine the left and right sides of the machine from the normal operating position. Important The Auxiliary Control Lever is shipped loose to prevent accidental engagement of the unused Caution hydraulic circuit. -
Page 14: Transporting The Equipment
• Increase the PTO speed to 540 RPM. • Make sure the towing vehicle has a rear view mirror and there is clear visibility behind the trailer. Caution • AVOID SHARP TURNS. Watch the tires of the tractor while turning to make sure they do not contact the tongue of the Versa Vac. -
Page 15: Inspection And Cleanup After Operation
Hand Held Remote Vacuum Hose Kit An optional Hand Held remote Vacuum Hose Kit, Model 07080 is available from your Toro Distributor. Hose door (Fig. 11) and Handle latch (Fig. 12) are only used when kit is installed. Figure 12 Warning 1. -
Page 16: Maintenance
100 hours of use (Fig. 14). Use a No. 2 whichever comes first. Lithium-based grease. Only the Toro replacement filter (Part No. 54–0110) can be used in the hydraulic system. Important Use of any other filter may void the... -
Page 17: Checking Hydraulic Lines And Hoses
1. Turn tractor engine off and remove key from ignition. Warning 2. Clean area around filter mounting area. Place drain pan under filter and remove filter. Hydraulic fluid escaping under pressure can penetrate skin and cause injury. • Make sure all hydraulic fluid hoses and lines are in good condition and all hydraulic connections and fittings are tight before applying pressure to the hydraulic system. -
Page 18: Storage
Storage 1. Thoroughly clean the Vac. The impeller housing should be free of dirt, leaves, and debris. 2. Check the tire pressure; refer to Checking the Tire Pressure. 3. Check all fasteners for looseness; tighten as necessary. 4. Grease or oil all grease fittings and pivot points. Wipe up any excess lubricant. -
Page 19: Hydraulic Schematic
Hydraulic Schematic FINGER DECK DECK LIFT DUMP COMBINATION DECK COMBINATION DECK DECK CYL FINGER DECK BOX DUMP CYL... -
Page 20: The Toro General Commercial Products Warranty
If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.