Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Soundstream Reference Series CLASS-A-3.0
Summary of Contents for Soundstream Reference Series CLASS-A-3.0
- Page 1 REFERE'NCE ClassA3,O ClassA6.0 Power Amplifiers OWNERS MANUAL INSTALLATION GUIDE SOUNDSTREAk”...
- Page 2 Soundstream amplifiers are the result of American craftsmanship and the highest quality control standards, and when properly installed, will provide you with many years of listening pleasure. Should your amplifier ever need service or replacement due to theft, please record the following information, which will help protect your investment.
-
Page 3: Table Of Contents
TABLE OF CONTENTS Features ... 4-5 REFERENCE Power Supply Design..6 Passive and Electronic Crossovers ..6 6 dB/octave Passive Crossover Chart ... 7 12 dB/octave Passive Crossover Chart ... 8 Series and Parallel Wiring ... 9 LSE.Q Theory and Use ... IO-I 1 Setting High Power/High Current Setting Coherent Stereom/Mixed Mono/Bridged Mono Wiring.. -
Page 4: Features
DEStGN FEATURES Pure Class A” Output Topology for the utmost in musicality and definitive power output. Soundstream’s uniqe design allows the Class A amplifiers to deliver uncomparable sonics or, when operated at lower impedances, to provide phenomenal amounts of power. - Page 5 ChassisinkTM Darlington Power Array - Soundstream’s “overbuilding” of the output section incorporates multiple output transistors instead of a few for faster, stronger power delivery. The transistors are sandwiched between the circuit board and the heatsink in a design called Chassisink” to ensure cool, efficient amplifier operation.
-
Page 6: Reference Power Supply Design
The REFERENCE Class A amplifiers employ an extremely efficient unregulated pulse-width modulated power supply. REFERENCE Class A amplifiers from Soundstream are rated at 12 volts but are designed to take advantage of the additional voltage available when the vehicle is running. The two major... -
Page 7: Db/Octave Passive Crossover Chart
PASSIVE CROSSOVER CHART /’ 6 dB/octave hiuh pass L = high quality (DCR < 1 ohm) inductor/coil C = non-polarized 50 v (or greater) capacitor 2 ohms FREQ. 1000 80 Hz 4.1 mH 100 Hz 3.1 mH 800 ti 130 Hz 2.4 mH 600 p!= 200 Hz... -
Page 8: Db/Octave Passive Crossover Chart
PASSIVE CROSSOVER CHART 12 dB/octave hioh L)ass Ll = high quality (DCR c 1 ohm) inductor/coil Cl = non-polarized 50 v (or greater) capacitor o h m s FREQ. 5.5 mH 80 Hz 680 pF 4.7 mH 100 Hz 560 pF 130 Hz 3.3 mH 400 pF... -
Page 9: Series And Parallel Wiring
SERIES AND PARALLEL WIRING Below are examples of series and parallel wiring configurations. Please note how the impedances differ with the different configurations. Amplifier Amplifier 2-4 ohm drivers in parallel ..‘14‘ = 2 ohms Amdifier 4-4 ohm drivers in parallel =I ohm 4Oh;... -
Page 10: Lse.q Theory And Use
LSE.Q THEORY AND USE LSE.Q is a unique subwoofer control circuit included with the REFERENCE SOUNDSTREAM Class A 6.0 amplifier. It is capable of subsonic energy removing The circuit program material. consists of two controls. One adjusts the frequency of operation and the other adjusts the range of boost. - Page 11 This serves the purpose of removing the “subsonic” bass energy. Soundstream’s LSE.Q contains the same type of circuit with the added benefit of infinite adjustability. Our “Q” and “Hz” control can provide virtually any combination of boost and cut to suit your designs.
-
Page 12: Installation Step
The circuit operates by selecting a set of power supply voltage rails best suited to your particular application. impedance applications while the other is lower voltage designed to provide more current. Unlike other amplifiers, Soundstream’s REFERENCE Class A amplifiers can be configured to drive virtually any impedance and make maximum power! -
Page 13: Setting Coherent Stereom/Mixed Mono/Bridged Mono
4 INSTALLATION STEP 2 b COHERENT STERE@/MIXED- MONO/BRIDGED MONO The REFERENCE Class A amplifiers have the ability to operate in any one of the following modes: COhWefIf sfWeOrM with identical left and right stereo channels for maximum fidelity. Best choice for satellite speakers. Use this mode unless Mixed-Mono is necessary. -
Page 14: Wiring
REFERENCE Class A 3.0 REFERENCE Class A 6.0 WIRING up to 10’ Soundstream Power40 or Power 80 (4 or 8 ga.) Soundstream Power40 or P o w e r 8 0 (4 or 8 ga.) replace the fuses with a higher value than... -
Page 15: Wiring Diagram
SPEAKER CABLE The REFERENCE amps will accept up to 8 gauge speaker cable. Use a high quality, flexible, multi-strand cable for best performance and longevity. Soundstream Speaker1 20 & 160 (12 and 16 gauge) are ideal. /------ FUSE WIRING (cont..) -
Page 16: Installation And Mounting
i INSTALLATION STEP 4 t INSTALLATION AND MOUNTING 1. AMPLIFIER LOCATION The REFERENCE Class A amplifiers employ highly efficient circuitry and a unique ChassisinkTM design to maintain lower operating temperatures. Additional cooling may be required if the amplifier is located in a tightly confined area or when driving especially low impedance loads at extremely high levels. -
Page 17: Level Setting
q INSTALLATION STEP 5 t The input levels are adjusted by means of the input level controls located on the front of the amplifier. This is a unique dual-stage circuit that adjusts both level and gain. This topology maintains better Signal to Noise ratios even when using sources with minimal output. -
Page 18: Protection Circuitry & Troubleshooting
Repeatedly blown amp fuse, frequent activation of Smart Power Supply Circuit Your Soundstream REFERENCE Class A amplifier is protected by a limited warranty. Please read the enclosed warranty card. no power or ground at amp 0 no remote turn-on signal... -
Page 19: Specifications
4 R Stereo POWER (8 R Bridged) REFERENCE class A 3.0 High Power 25 x 2 (50 x 1) Watts High Current 12.5 x 2 (25 x 1) Watts REFERENCE C/ass A 6.0 50 x 2 High Power (100 x 1) Watts High Current 25 x 2... - Page 20 SOUNDSTREAM@ SOUNDSTREAM TECHNOLOGIES 120 Blue Ravine Road . Folsotn . California 95630 USA ph 916.351.1288 . fax916.351.0414 twvc - 1.13.05...
Need help?
Do you have a question about the Reference Series CLASS-A-3.0 and is the answer not in the manual?
Questions and answers