Sony DR-BT1 Operating Instructions

2-186-671-12(2)
Bluetooth ® Earset
System
Operating Instructions
Manual de instrucciones
DR-BT1K
© 2004 Sony Corporation Printed in Malaysia
What's Bluetooth?
THIS PRODUCT IS MANUFACTURED UNDER ONE
Bluetooth is a new technology that enables wireless data
OR MORE OF THE FOLLOWING SONY U.S.
communication by mobile phones, computers or other
PATENTS:
4,429,194; 4,736,435; 4,668,842; AND OTHER mobile devices.
Bluetooth wireless technology operates within a range of
PATENTS ISSUED OR PENDING IN U.S. AND
about 10 meters* (about 30 feet).
OTHER COUNTRIES
* Obstacles (body, metal, wall, etc.) or reception conditions
may adversely affect the usable range.
English
Bluetooth earset adaptor
Owner's Record
Optimal
The model and serial number are located at the rear of the
performance
Bluetooth earset and on the belt clip of the Bluetooth earset
Bluetooth
adaptor.
earset Limited
Record these numbers in the spaces provided below. Refer
Steel cabinet
performance
to them whenever you call upon your Sony dealer regarding
this product.
Notes
Model No. DR-BT1K
• Bluetooth communication may be affected by the
Bluetooth earset : DR-BT1
conditions below.
Bluetooth earset adaptor : DRC-BT1
– Obstacles between the Bluetooth earset and the
Serial No.
Bluetooth earset adaptor or Bluetooth mobile phone
Bluetooth earset: - - - - - - - - - - - - - - - - - - - - - - - -
: Body, metal, walls, etc.
Bluetooth earset adaptor: - - - - - - - - - - - - - - - - - -
– Electromagnetic waves
: A place where a wireless LAN is installed, a
WARNING microwave oven is used, or where electromagnetic
energy exists
• The above is also subject to the mobile phone's antenna
To prevent fire or shock hazard, do not expose the
unit to rain or moisture. and reception conditions.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
N Getting started
Information
Unpacking
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
Check that you have the following items:
This device may not cause harmful interference, and (2) this
device must accept any interference received, including
• Bluetooth earset (1)
interference that may cause undesired operation.
You are cautioned that any changes or modifications not
with a hanger (Size M)
expressly approved in this manual could void your authority
to operate this equipment.
• Hanger (Size S) (1)
Note :
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
• Bluetooth earset adaptor (1)
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
• AC power adaptor (1)
by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/ TV
technician for help. • Car attachment (1)
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
Hook (S) (1) Hook (L) (1) Spacer (2)
This equipment complies with FCC radiation exposure
limits set forth for uncontrolled equipment and meets the
FCC radio frequency (RF) Exposure Guidelines in
Supplement C to OET65. This equipment has very low
levels of RF energy that it is deemed to comply without
• Warranty (1)
testing of specific absorption ratio (SAR).
• Operating Instructions (1)
The Bluetooth word mark and logos are owned by the
Bluetooth SIG, Inc. and any use of such marks by SONY is
under license.
Identifying
For the customers in the USA
Bluetooth earset
– Recycling of battery in Bluetooth earset
Bluetooth earset is referred to as "earset" in this manual.
RECYCLING LITHIUM-ION BATTERIES
7
Lithium-Ion batteries are
recyclable. You can help preserve
2
our environment by returning your
used rechargeable batteries to the
3
collection and recycling location
1
nearest you. 4
L
For more information regarding
R
recycling of rechargeable batteries, call toll free
8
1-800-822-8837, or visit http://www.rbrc.org/
Caution:
5
Do not handle damaged or leaking Lithium-Ion
batteries.
6
–Recycling of battery in Bluetooth earset adaptor
RECYCLING NICKEL METAL HYDRIDE
1 Hanger
BATTERIES
2 LED indicator
Nickel Metal Hydride batteries are
Indicates the status of the earset.
recyclable. You can help preserve
3 VOLUME +
our environment by returning your
used rechargeable batteries to the
4 VOLUME –
collection and recycling location
5 Pipe microphone
nearest you.
For more information regarding 6 Housing
recycling of rechargeable batteries, call toll free
7 Multi button
1-800-822-8837, or visit http://www.rbrc.org/
Controls various functions of the earset.
Caution:
8 Contact terminals
Do not handle damaged or leaking Nickel Metal
Hydride batteries.
Bluetooth earset adaptor
Bluetooth earset adaptor is referred to as "earset adaptor" in
Welcome!
this manual.
Thank you for purchasing the Sony DR-BT1K Bluetooth
earset system. Before operating the unit, please read this
1
manual thoroughly and retain it for future reference.
5
Some features are:
• Wireless system that allows you to talk by mobile phone.
4
• Car Air-vent clip for car use.
• Fits on either your right or left ear.
• Convenient earset adaptor with belt clip
• Up to 5 hours for talking. Up to 100 hours for standby.
6
• Flexible pipe microphone.
• Volume control function on the earset.
2 3
1 LED indicator
Indicates the status of the earset adaptor.
2 POWER ON button
3 Pairing/Power off button
4 Contact pins
5 Belt clip
6 DC IN 4.5 V jack
N Operating the system
Charging the units
Usage
The earset contains a rechargeable Lithium-Ion battery and
the earset adaptor contains a Nickel-Metal Hydride battery,
There are two ways to use the units, depending on your
which should be charged before using for the first time.
mobile phone.
1
Dock the earset with the earset adaptor. • To use a mobile phone without Bluetooth
Use the earset and the earset adaptor connected to the
mobile phone.
• To use a mobile phone with Bluetooth
Use the earset and the mobile phone. The earset adaptor is
not necessary.
Turning on/off the earset
Turning on the earset
2
Connect the supplied AC power adaptor to
Press and hold the Multi button on the
the DC IN 4.5 V jack on the earset adaptor.
earset for about 7 seconds until the LED
When the AC power adaptor is connected to an AC blinks blue.
outlet, Charging starts.
The unit turns on and the LED starts to blink blue
every 3 seconds.
To an AC outlet
AC power adaptor
(supplied)
Note
Take care not to press and hold the Multi button for
more than 10 seconds, otherwise pairing mode is
entered.
To DC IN 4.5 V jack
Tip
Tip A low/high beep is heard through the earset when it is
When the AC power adaptor is connected to an AC turned on.
outlet, both units will turn off automatically.
Turning off the earset
3
Make sure that both indicators light up
Press and hold the Multi button on the
green while charging.
earset for about 3 seconds until the LED
blinks green, then goes off.
Both indicators light up
green.
Note
Charging is completed in about 2.5 hours* and the
When the earset is turned off, the current volume level
indicators go off automatically.
is stored, except when turned off during charging.
* Time required for empty battery to recharge.
Tip
Note A high/low beep is heard through the earset when it is
turned off.
If the LED on the earset does not light up green, dock
again, and make sure that the indicator lights up green.
Turning on/off the earset adaptor
Caution
If this unit detects a problem while charging, the LED may
Turning on the earset adaptor
blink green, and will turn off although the charge is not
complete.
Press and hold the POWER ON button for
Check for the following causes:
a few seconds until the LED lights up blue
– Environmental temperature exceeds the range of 0˚C-
and green, then goes off.
40˚C (32˚F-104˚F).
The unit turns on and the LED starts to blink blue
– There is a problem with the battery.
every 10 seconds.
In this case, charge again within the above-mentioned
temperature range.
If the problem persists, consult your nearest Sony dealer.
Notes
• The unit cannot operate while charging.
• Charge in an environmental temperature of between
0˚C and 40˚C (between 32˚F and 104˚F).
• Avoid exposure to temperature extremes, direct sunlight,
moisture, sand, dust or mechanical shock. Never leave in
a car parked in the sun.
Turning off the earset adaptor
• Use only the supplied AC power adaptor. Do not use any
other AC power adaptor. 1
Make sure that the earset is turned off.
2
Press and hold the Pairing/Power off
button for about 12 seconds until the LED
lights up blue and green, then goes off.
Polarity of the plug Use the point of the hanger on the earset or a similar
instrument.
The low battery display
The LED display colour of either unit changes from blue to
green when battery charge is low.
(In some cases, the earset adaptor LED may light
permanently blue.)
In this case, recharge the battery immediately.
After use, recharge the unit frequently.
Recommended accessory
Car Multi-Voltage DC Adaptor: DCC-E345
Notes
Buy Sony Accessories at URL:
• When the earset is turned on, the earset adaptor
http://www.sony.com/sonyaccessories
cannot be turned off. Turn off the earset adaptor
or call 1-888-559-7669 (SONY)
after turning off the earset.
Note
• If you release the Pairing/Power off button too
Never leave this unit charging unattended in a car.
soon, pairing mode is entered. In pairing mode, the
earset adaptor can be turned off by holding down
Charging and usage hours
the button for about 12 seconds.
Usage time from fully charged.
Earset Earset adaptor Connect the earset adaptor to
<DR-BT1> <DRC-BT1>
your mobile phone
Talk time 7 hours 5 hours
(up to)
To use a mobile phone without Bluetooth, connect the
earset adaptor.
Standby time 160 hours 100 hours
Insert the earset adaptor's plug into the tri-pole jack of your
(up to)
mobile phone.
Time stated above may vary, depending on ambient
2.5 mm tri-pole jack
temperature or conditions of use.
Notes
• If the battery is not used for a long time, the battery
charge may quickly deplete, however, after a few
recharges, battery life will improve.
• If the life of the built-in rechargeable battery drops to
half the normal length, the battery should be replaced.
Consult your nearest Sony dealer for replacement of the
rechargeable battery.
Wearing the earset
1
Hook the earset around your ear, as you
would glasses.
2
Adjust the position of the earset to fit
comfortably.
Changing the direction of the
hanger
This unit can be worn on the right or left ear by the
following procedure.
Example: When changing over from right to left ear.
1
Holding the housing firmly, unlatch the
hanger assembly.
L
2
Holding the housing, rotate the hanger,
and then pull out in the direction of the
arrow.
g
L
L
3
Rotate the housing to the other side.
L
R
4
Attach the hanger in the direction of the
arrow as illustrated below.
L
Marked
L R
Marked Marked
Note
The housing and the hanger are marked left (L) and right
(R). For example, when using the left ear, the housing is set
in the L position, and the hanger is attached with the L
mark visible.
Tip
The unit comes with 2 hanger sizes to ensure a comfortable
fit. (A hanger (Size M) is attached with the earset, when it is
delivered.)
To use a mobile phone To use a mobile phone
without Bluetooth with Bluetooth
The earset can connect directly to a Bluetooth mobile
– Basic operation
phone. Therefore, the earset adaptor is not necessary.
The operation flow is described as follows.
–Introduction
A Turn on the units To pair the earset with a
Bluetooth mobile phone
Standby mode The earset needs to be paired with a Bluetooth mobile
phone.
Once the earset (DR-BT1) is registered in the mobile phone,
there is no need for pairing again.
B Start communication between But in the following cases, pairing is necessary again.
the earset and the earset • The earset is paired with other Bluetooth equipment.
• The registration (DR-BT1) in the mobile phone is
adaptor
removed.
Press the Multi button.
Note
For details, refer to the manual supplied with your
Bluetooth mobile phone.
C Call
1
Place the earset and the Bluetooth mobile
1 Call/Receive a call
phone within 1m (3 ft) of one another.
Operate your mobile phone
2 Talk on the phone
within 1m (3 ft)
3 Terminate a call
Operate your mobile phone
D Terminate communication 2
While the earset is turned off, press and
between the units
hold the Multi button for about 10 seconds.
Press the Multi button.
Keep pressed until the LED blinks blue and green,
indicating pairing mode.
A
Turn on the units
Refer to "Turning on/off the earset" and "Turning on/
off the earset adaptor" for details.
B
Start Communication
between the earset and the
Note
earset adaptor
Keep pressed while the LED blinks blue for the first 7
of the 10 seconds.
Press the Multi button on the earset.
The earset and the earset adaptor start communication, 3
Search the earset by the Bluetooth mobile
and sound from the mobile phone is heard on the
phone.
earset. The pipe microphone transmits your voice to
When the Bluetooth mobile phone detects the earset,
the mobile phone.
"DR-BT1" will appear in the display of the Bluetooth
mobile phone.
Note
The pairing mode is canceled after about 60 seconds.
If the LED returns to blinking blue (every 3 seconds),
repeat from step 1.
4
Select "DR-BT1" in the list displayed on
your Bluetooth mobile phone.
If "DR-BT1" is not displayed, repeat from step 1.
The LED display during audio communication
Earset: Blue blink 3 times (every 3 seconds) 5
Input the passkey* [0000] when requested
Earset adaptor: Blue blink (every second)
by your Bluetooth mobile phone.
Notes
If the LED on the earset changes from blinking blue
• Communication sensitivity will be increased if
and green to blinking blue slowly (every 3 seconds),
there are no obstacles between the earset and the the pairing has completed.
earset adaptor.
The display of the Bluetooth mobile phone will
• Sound will be heard after a few seconds of pressing
usually show that pairing has completed.
the Multi button.
* Passkey may also be called the following.
• After 2 hours (approx.), audio communication will
– Pass code, PIN code, PIN number, Password.
terminate automatically.
Tip
–Basic operation
A beep is heard through the earset to confirm that
audio communication starts.
The operation flow is described as follows.
C
Call
A Prepare the Bluetooth mobile
phone to be connected
To call:
Use the keypad of your mobile phone to dial the
B Turn on the earset
number, then press the call button.
To receive a call:
Answer the call as you normally would, using the
C Connect between the earset
receive button.
and the Bluetooth mobile
Tip phone
The auto-receiving function on your mobile phone
Press the Multi button.
makes this more convenient, especially when you are
driving.
To terminate a call: Standby mode
Press the end button of your mobile phone.
Tip
If your mobile phone is equipped with a voice-dial D Call (audio communication)
function, you can dial by the pipe microphone. Refer
to the manual supplied with your mobile phone about 1 Call
the voice-dial function.
Operate your mobile phone
D Receive a call
Terminate communication
Press the Multi button
between the units
Press the Multi button on the earset.
2 Talk on the phone
Audio communication terminates. The earset and the
earset adaptor return to the standby mode.
3 Terminate a call
Press the Multi button
A Prepare the Bluetooth mobile
Tip
phone to be connected
A beep is heard through the earset to confirm that
audio communication terminates.
Activate the Bluetooth function of the
Bluetooth mobile phone to be connected
– Other operations
to the earset.
For details, refer to the manual supplied with your
To adjust the volume
Bluetooth mobile phone.
Press VOLUME + or – during audio communication. A
beep corresponding to the selected volume is heard every
B Turn on the earset
time you press either button.
The volume does not change although the beep sound is
Refer to "Turning on/off the earset" for details.
heard when not communicating. When the volume setting is
C
maximum or minimum, the beep does not sound. Connect between the earset
and the Bluetooth mobile
VOLUME + VOLUME –
phone
Press the Multi button on the earset.
Some Bluetooth mobile phones can be operated while
connected to the earset.
Note
Tip In the following cases, connect again between the
earset and the Bluetooth mobile phone.
When the sound is low, raise the volume of your mobile
phone. The sound will be clearer. – the earset is turned off
– the Bluetooth mobile phone (or its Bluetooth
function) is turned off
– the Bluetooth function on the Bluetooth mobile
phone and the earset are in sleep mode
– Bluetooth connection has terminated
Refer to the manual supplied with your Bluetooth
mobile phone about Bluetooth connection and the
Bluetooth function.
D Call
To call:
Use the keypad of your Bluetooth mobile phone to
dial the number, then press the call button. If there is
no sound from the earset, press the Multi button.
Tip
It is possible to call in various ways, depending on the
Bluetooth mobile phone. Refer to the manual supplied
with your Bluetooth mobile phone.
– You can call by pressing the Multi button using the
voice-dial function when in standby.
– You can call to the last number dialed by holding
the Volume + or – button (only when using Hands-
free profile).
– You can call a specific number by pressing the
Multi button.
To receive a call:
When the telephone is ringing, sound will be heard
through the earset. Press the Multi button on the
earset.
Sound differs depending on your mobile phone.
– the earset sound
– the mobile phone sound (When using the Bluetooth
function, it may be a specific sound.)
Note
If you pressed the call button on the Bluetooth mobile
phone, some Bluetooth mobile phones may have
handset use priority. In this case, set to talk with the
earset by pressing the Multi button, or by operating
the Bluetooth mobile phone.
For details, refer to the manual supplied with your
Bluetooth mobile phone.
To terminate a call:
You can end a call by pressing the Multi button on the
earset.
In the following cases, audio communication
terminates automatically.
– the end button on the Bluetooth mobile phone is
pressed
– the recipient hangs up
The LED display during audio communication
Earset: Blue blink 3 times (every 3 seconds)
–Other operations
How to use the car
To adjust the volume
attachment
Press VOLUME + or – during connection. A beep
corresponding to the selected volume is heard every time
The car attachment (supplied) can be used to hold the earset
you press either button.
adaptor, by installing it in the vent of the air conditioner of
When the volume setting is maximum or minimum, the
your car.
beep does not sound.
This is convenient for using while driving.
VOLUME + VOLUME –
Standard installation
Horizontal fin
9 mm ( 3 / in)
8
17 mm ( 11 / in)
16 (min)
(max)
Tip 3 mm ( 1 / in)
8
When the sound is low, raise the volume of your mobile (max)
7 mm ( 9 32 / in)
phone. The sound will be clearer. (min)
Note
The volume does not change although the beep sound is
heard when not communicating (only when using the Vertical fin
Headset profile).
1
3 mm ( / 8 in) (max)
7 mm ( 9 / in) (min)
32
Operation of the units'
9 mm ( 3 / 8 in) (min)
buttons
To pair with the earset adaptor
Operation of the earset buttons
17 mm ( 11 / 16 in) (max)
Multi button VOLUME +/– button
Notes
Status Short Press Long Press Short Press Long Press • The car attachment may not be installable. Do not install
the unit by force if installation is difficult. This may
Off – Power ON – –
break a fin.
Standby Communicate Power OFF – –
• Take care not to install or remove the unit by force. A fin
Call active Discomunicate Power OFF Adjust volume Mic Mute* may break.
by one step
• If necessary, protect the dashboard and the air
conditioner vent with tape, etc., so as not to damage
* The beep sounds every 3 seconds while the microphone anything.
is muted. • Install this unit in a place that does not disturb the air bag
To cancel muting, press the VOLUME + or – button.
function or your driving.
• Be sure to turn off the vent's auto-swing function if your
Operation of the earset adaptor buttons car has one.
POWER ON Pairing/Power off
To install the car attachment
Status Short Press Long Press Short Press Long Press
1
Attach the hook to the rear of the
Off Power ON – – –
attachment. Ensure it is the correct way
Standby – – – Pairing round. (See illustration.)
(about 3 sec.)/
Power off *
(about 12 sec.)
Call active – – – –
When the earset is turned on, the earset adaptor cannot be
*
turned off. First, turn off the earset, then turn off the earset
adaptor.
To pair with a Bluetooth mobile
phone
2
Attach the spacer under the hook firmly
Operation of the earset buttons
after peeling off the double-sided tape.
The operation of the buttons on the earset varies depending
on the pairing device. Headset profile or Hands-free profile
is used for Bluetooth mobile phone pairing.
Refer to the manual supplied with your Bluetooth mobile
phone.
Headset Profile* 1
Spacer
Multi button VOLUME +/– button
3
Insert the hook in the vent of the air
Status Short Press Long Press Short Press Long Press
conditioner. Ensure the hook is firmly
Off – Power ON – –
clipped to the fin.
Standby – Power OFF – –
Start Voice Dial Cancel Voice Power OFF – –
Dial
Ringing Answer Power OFF – –
Call active End Call Power OFF Adjust volume Mic Mute* 2
by one step
Hands-free Profile* 1
4
Dock the earset adaptor's belt clip to the
Multi button VOLUME +/– button
attachment.
Status Short Press Long Press Short Press Long Press
Off – Power ON – –
Standby Initiate Voice Power OFF Adjust volume Last number
Dial by one step Redial
Setting up Voice Cancel Voice Power OFF – –
Dial Dial
Ringing Answer Reject – –
Call active End Call Power OFF Adjust volume Mic Mute* 2
by one step
Tips
* 1 Some functions may not be supported, depending on • Use the other hook (L) if the air conditioner is sloped.
your Bluetooth mobile phone.
Refer to the manual supplied with your Bluetooth mobile
phone.
* 2 The beep sounds every 3 seconds while the microphone
is muted. Hook (S)
To cancel muting, press the VOLUME + or – button.
Hook (L)
Indication of the LED
Status Earset Earset adaptor • You can adjust the angle of the attachment by sliding the
<DR-BT1> <DRC-BT1> rear of the car attachment.
Power on Blue blink Blue/Green light
for 1 sec.
Power off Green blink Blue/Green light,
for 2 sec. then goes off
Standby Blue blink Blue blink
every 3 sec. every 10 sec.
Call active Blue blink Blue blink
• Install the hook to face to the side if the fin of the air
3 times every 1 sec.
conditioner is vertical.
every 3 sec.
Pairing mode Blue/Green Blue/Green
blink blink
Notes
g
• The LED colour of either unit changes from blue to
green when battery charge is low.
• Communication may sometimes not occur, even though
the Multi button on the earset is pressed. In such a case,
the LED double blinks (blue) 3 to 5 times, after which
• Add another spacer (you will need to modify/fabricate
the earset enters standby mode.
this yourself) if the car attachment is unstable.
Failure to communicate will occur in the following cases:
– The earset adaptor is not turned on.
To remove the attachment
– The earset is not paired with the earset adaptor or your
Bluetooth mobile phone.
1
Push the car attachment back, and push it
– The Bluetooth function on your Bluetooth mobile
gently off the vent.
phone is not activated.
2
Remove the attachment while pressing the
fin.
Note
If the attachment is pulled out and catches a fin, it may
damage it.
To pair the earset with Troubleshooting
the earset adaptor
Problem Solution
The earset and earset adaptor come already paired
from the factory. To pair the earset and earset The recipient's voice Check that the earset adaptor is
adaptor again after use, do the following. cannot be heard. connected to the mobile phone
correctly.
Note
Check that the jack of your
The earset adaptor is designed specifically for the earset;
communication with other equipment is not guaranteed. mobile phone is a 2.5 mm
tri-pole jack.
1
Place the earset and the earset adaptor Plug the earset adaptor in
close together within 1m (3 ft). properly.
Check that the power of the
earset and the earset adaptor
are on.
Check the volume of your
mobile phone.
within 1m (3 ft)
Check the volume of the
earset.
Make the pairing of the earset
and the earset adaptor again
when the earset is connected to
2 another Bluetooth product.
While the earset is turned off, press and
hold the Multi button for about 10 seconds.
Low sound from recipient Check that the jack of your
mobile phone is a 2.5 mm
Keep pressed until the LED blinks blue and green
indicating pairing mode. tri-pole jack.
Plug the earset adaptor in
properly.
Turn up the volume on your
mobile phone.
The recipient cannot hear Check that the earset adaptor is
or easily hear your voice. connected to the mobile phone
correctly.
Note
Check that the jack of your
Keep pressed while the LED blinks blue for the first 7
mobile phone is a 2.5 mm
of the 10 seconds.
tri-pole jack.
3
Press the POWER ON button of the earset
Plug the earset adaptor in
adaptor.
properly.
Release the mute of Mic by
pressing the volume button
once when the Mic of the
earset is muted. (Intermittent
beep sound can be heard
during muting.)
Power does not turn on. Recharge both units.
4 The units cannot be turned on
With the point of the hanger on the earset
when charging. Unplug the
or a similar instrument, press and hold the
AC power adaptor from the
Pairing/Power off button for about 3
earset adaptor.
seconds.
The earset adaptor's Due to the battery characteris-
Keep pressed until the LED lights up blue and green.
usable time is short. tics, its usable time might
The LED starts to blink blue and green indicating
become short depending on
pairing mode.
circumstances.
When the battery is not used
for a long time, a few
recharges will restore its
performance.
The power of earset Turn off the power of the
adaptor cannot be turned earset adaptor after turning off
off. the earset.
After the earset LED's blue/green blinking changes to
The correspondence If there are the obstacles
blink only blue slowly (every 3 seconds) indicating
distance is short. (The between the earset and the
Stangby mode, the pairing is completed.
noise mixes with the earset adaptor or the Bluetooth
voice. ) mobile phone, remove or
Note
avoid the obstacles.
Use pairing mode to pair the units.
Time out for pairing mode either unit is as follows:
If there is equipment that
Earset: about 60 seconds.
generates electromagnetic
Earset adaptor: about 20 seconds.
radiation, etc., such as a
If the LED's blue/green blinking goes off before
wireless LAN, other Bluetooth
pairing, repeat from step 1.
equipment, a microwave oven
5 nearby, move away.
After the pairing is completed without any
Pairing can not be done. Pair the units by bringing the
problems
earset and the earset adaptor or
Press the Multi button on the earset and make sure
the Bluetooth mobile phone
that audio communication starts between the earset
close together.
and the earset adaptor.
When audio communication starts, the earset LED
The earset cannot be Dock the earset with the earset
blinks blue 3 times every 3 seconds, and the earset
charged. adaptor so that the LED turns
adaptor LED blinks blue every second.
green.
When the contact terminal on
the earset and the contact pins
N Additional information
on the earset adaptor are dirty,
wipe them lightly with a soft
dry cloth.
Disposing of the earset
and adaptor
Precautions
For environmental conservation, be sure to remove the
built-in rechargeable batteries from the units before you
• Avoid using Bluetooth earset with the volume turned up
dispose of them, and dispose of the batteries appropriately.
for an extended period of time. Doing so can damage
your hearing. Listening at high volumes may also cause
Remove the battery from the
howling depending on the equipment connected with the
earset earset. It is advisable to keep the volume at a moderate
level at all times.
• Do not leave the Bluetooth earset system in a location
1
Remove the two screws from the rear.
subject to direct sunlight, heat, moisture or in a parked
car.
• Consult local lows and regulations regarding use of the
Bluetooth earset while driving or cycling.
• Using the Bluetooth earset may not function on mobile
L
R phones, depending on radio wave conditions and location
where the equipment is being used.
• If you experience discomfort after wearing the Bluetooth
earset, take off the Bluetooth earset immediately.
2
Push hard around the arrow as illustrated
• Start dialing after connecting the Bluetooth earset to your
to unlatch the unit assembly.
mobile phone.
Caring for others
• If you have any questions or problems concerning the
system that are not covered in this manual, please consult
your nearest Sony dealer.
• Be sure to bring the Bluetooth earset and the Bluetooth
earset adaptor to the Sony dealer when requiring repair
3
Lift the pipe microphone slightly. work.
Notes on Car attachment
• Make sure this unit is fixed firmly before driving to avoid
an accident or damage.
• Do not handle the Bluetooth earset adaptor while driving.
• Do not leave the Bluetooth earset adaptor inside a car in
high temperature. This may damage the fins or this unit.
4
Remove the battery holder with battery
• Take care that the Bluetooth earset and the Bluetooth
first, then remove the battery from the
earset adaptor do not fall down while driving and during
battery holder.
use.
• The car attachment is only for the Bluetooth earset
Battery holder
adaptor. Do not install other device, as it may cause an
accident or damage by dropping, etc.
• Be sure to keep the unit out of the reach of children as it
has small parts.
Specifications
General
5
Remove the connector. Bluetooth Compliance: Bluetooth standard Ver. 1.1
Output power: Bluetooth standard Power Class2
Frequency band: 2.4 GHz band
(2.4000 GHz – 2.4835 GHz )
Max. Communication range:
Line of sight approx. 10 m (32.8 ft)
Supplied accessory: AC power adaptor (1),
Hanger (S) (1), Car attachment (1)
Bluetooth earset DR-BT1
Supported Bluetooth Profiles:
Headset Profile, Hands-free Profile
Power source: DC 3.7 V: Built-in Li-ion
Remove the battery from the
rechargeable battery
earset adaptor Typical Talk time: 7 hours
Typical Standby Time: 160 hours
Mass: Approx. 20 g (0.71 oz)
1
Remove the screw from the rear and raise
the cover by the belt clip.
Receiver
Type: Open air, dynamic
Driver unit: 13.5 mm dome type
(CCAW Voice Coil)
Sensitivity: 104 dB/mW
16 Ω at 1 kHz
Impedance:
Power handling capacity: 50 mW (IEC)
g
Reproduction frequency range:
50 – 20,000 Hz
Microphone
Type: Flexible pipe microphone
2
Remove the connector and pull out the Unit: Electret condenser
Output impedance: Under 2.2 kΩ
battery.
Open circuit voltage level: -42 dB (0 dB = 1 V/Pa)
Effective frequency range: 100 – 5,000 Hz
Bluetooth earset adaptor DRC-BT1
Supported Bluetooth Profiles:
Headset Profile
g
Power source: DC 1.2 V: Built-in Ni-MH
rechargeable battery
Typical Talk time: 5 hours
Typical Standby Time: 100 hours
Cord: 0.20 m (0.7 ft)
(Max. stretch length 0.7 m (2.3 ft))
Note
Plug: 2.5 mm tri-pole plug
Be careful not to touch the circuit board attached to the
Mass: Approx. 35 g (1.24 oz)
battery box. Hold the battery box (black plastic box) when
(without cord)
you remove the battery.
Design and specifications are subject to change without
notice.