Sony DR-BT1 Operating Instructions

2-186-672-12(3)
Bluetooth ® Earset
Operating Instructions
Manual de instrucciones
DR-BT1
© 2004 Sony Corporation Printed in Malaysia
Welcome!
THIS PRODUCT IS MANUFACTURED UNDER ONE
OR MORE OF THE FOLLOWING SONY U.S. Thank you for purchasing the Sony DR-BT1 Bluetooth
earset. Before operating the unit, please read this manual
PATENTS:
4,429,194; 4,736,435; 4,668,842; AND OTHER thoroughly and retain it for future reference.
Some features are:
PATENTS ISSUED OR PENDING IN U.S. AND
• Wireless system that allows you to talk by mobile phone.
OTHER COUNTRIES
• Car Air-vent clip for car use.
• Fits on either your right or left ear.
• Convinient charger with belt clip
• Up to 7hours for talking. Up to 160hours for standby.
• Flexible pipe microphone.
English
• Volume control function on the headset.
Owner's Record
What's Bluetooth?
The model and serial number are located at the rear of the
Bluetooth earset. Bluetooth is a new technology that enables wireless data
Record these numbers in the spaces provided below. Refer communication by mobile phones, computers or other
to them whenever you call upon your Sony dealer regarding mobile devices.
this product. Bluetooth wireless technology operates within a range of
about 10 meters* (about 30 feet).
Model No. DR-BT1
* Obstacles (body, metal, wall, etc.) or reception conditions
Serial No. ------------------------------------------
may adversely affect the usable range.
WARNING
To prevent fire or shock hazard, do not expose the Bluetooth mobile phone
unit to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
Optimal
performance
Information
Bluetooth
This device complies with Part 15 of the FCC Rules. earset
Limited
Operation is subject to the following two conditions: (1) Steel cabinet
performance
This device may not cause harmful interference, and (2) this
device must accept any interference received, including
Notes
interference that may cause undesired operation.
• Bluetooth communication may be affected by the
conditions below.
You are cautioned that any changes or modifications not
– Obstacles between the Bluetooth earset and the
expressly approved in this manual could void your authority
Bluetooth mobile phone
to operate this equipment.
: Body, metal, walls, etc.
Note :
– Electromagnetic waves
This equipment has been tested and found to comply with
: A place where a wireless LAN is installed, a
the limits for a Class B digital device, pursuant to Part 15 of
microwave oven is used, or where electromagnetic
the FCC Rules. These limits are designed to provide
energy exists
reasonable protection against harmful interference in a
• The above is also subject to the mobile phone's antenna
residential installation. This equipment generates, uses and
and reception conditions.
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
N Getting started
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
Unpacking
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
Check that you have the following items:
by one or more of the following measures:
• Bluetooth earset (1)
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
with a hanger (Size M)
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/ TV
• Hanger (Size S) (1)
technician for help.
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
This equipment complies with FCC radiation exposure
limits set forth for uncontrolled equipment and meets the
FCC radio frequency (RF) Exposure Guidelines in
Supplement C to OET65. This equipment has very low • Battery charger (1)
levels of RF energy that it is deemed to comply without
testing of specific absorption ratio (SAR).
The Bluetooth word mark and logos are owned by the
Bluetooth SIG, Inc. and any use of such marks by SONY is
under license. • AC power adaptor (1)
For the customers in the USA
– Recycling of battery in Bluetooth earset
RECYCLING LITHIUM-ION BATTERIES
Lithium-Ion batteries are • Car attachment (1)
recyclable. You can help preserve
our environment by returning your
used rechargeable batteries to the
collection and recycling location
Hook (S) (1) Hook (L) (1) Spacer (2)
nearest you.
For more information regarding recycling of
rechargeable batteries, call toll free
1-800-822-8837, or visit http://www.rbrc.org/
• Warranty (1)
Caution: • Operating Instructions (1)
Do not handle damaged or leaking Lithium-Ion
batteries.
The low battery display
Identifying
The LED display color of the unit changes from blue to
green when battery charge is low.
Bluetooth earset
In this case, recharge the battery immediately.
After use, recharge the unit frequently.
Bluetooth earset is referred to as "earset" in this manual.
Recommended accessory
7
Car Multi-Voltage DC Adaptor : DCC-E345
2
Buy Sony Accessories at URL :
http://www.sony.com/sonyaccessories
3
or call 1-888-559-7669 (SONY)
1
4
Note
L
Never leave this unit charging in a car.
R
8
Charging and usage hours
Usage time from fully charged.
5
Earset
6
Talk time (up to) 7 hours
Standby time (up to) 160 hours
1 Hanger
2 LED indicator Time stated above may vary, depending on ambient
temperature or conditions of use.
Indicates the status of the earset.
3 VOLUME +
Notes
• If the battery is not used for a long time, the battery
4 VOLUME –
charge may quickly deplete, however, after a few
5 Pipe microphone
recharges, battery life will improve.
• If the life of the built-in rechargeable battery drops to
6 Housing
half the normal length, the battery should be replaced.
7 Multi button Consult your nearest Sony dealer for replacement of the
Controls various functions of the earset. rechargeable battery.
8 Contact terminals
Wearing the earset
Battery charger
1
1 Hook the earset around your ear, as you
would glasses.
2
3
1 Contact pins 2
Adjust the position of the earset to fit
2 Belt clip comfortably.
3 DC IN 4.5 V jack
Changing the direction of the
hanger
Charging the unit
This unit can be worn on the right or left ear by the
following procedure.
The earset contains a rechargeable Lithium-Ion battery, that
Example: When changing over from right to left ear.
should be charged before using for the first time.
1
Holding the housing firmly, unlatch the
1
Dock the earset with the Battery charger.
hanger assembly.
L
2
Connect the supplied AC power adaptor to
the DC IN 4.5 V jack on the Battery
charger.
2
Holding the housing, rotate the hanger,
When the AC power adaptor is connected to an AC
and then pull out in the direction of the
outlet, Charging starts.
arrow.
To an AC outlet
g
L
L
AC power adaptor
(supplied)
3
To DC IN 4.5 V jack Rotate the housing to the other side.
Tip
When the AC power adaptor is connected to an AC
outlet, the unit will turn off automatically.
3
Make sure that the indicator lights up L
R
green while charging.
4
The indicator lights up Attach the hanger in the direction of the
green.
arrow as illustrated below.
L
Marked
Charging is completed in about 2.5 hours* and the
indicator goes off automatically.
L R
Marked Marked
* Time required for empty battery to recharge.
Note
Note
If the LED on the earset does not light up green, dock The housing and the hanger are marked left (L) and right
again, and make sure that the indicator lights up green. (R). For example, when using the left ear, the housing is set
Caution in the L position, and the hanger is attached with the L
mark visible.
If this unit detects a problem while charging, the LED may
blink green, and will turn off although the charge is not
Tip
complete.
The unit comes with 2 hanger sizes to ensure a comfortable
Check for the following causes:
fit. (A hanger (Size M) is attached with the earset, when it is
– Environmental temperature exceeds the range of 0˚C-
delivered.)
40˚C (32˚F-104˚F).
– There is a problem with the battery etc.
In this case, charge again within the above-mentioned
temperature range.
If the problem persists, consult your nearest Sony dealer.
Notes
• The unit cannot operate while charging.
• Charge in an environmental temperature of between
0˚C and 40˚C (between 32˚F and 104˚F).
• Avoid exposure to temperature extremes, direct sunlight,
moisture, sand, dust or mechanical shock. Never leave in
a car parked in the sun.
• Use only the supplied AC power adaptor. Do not use any
other AC power adaptor.
Polarity of the plug
N Operating the system – Basic operation
The operation flow is described as follows.
Operating the unit
A Prepare the Bluetooth mobile
To use this unit with your
phone to be connected
Bluetooth mobile phone
B Turn on the earset
The earset can connect directly to your Bluetooth mobile
phone. For details, refer to the manual supplied with your
Bluetooth mobile phone.
C Connect between the earset
and the Bluetooth mobile
Turning on/off the earset
phone
Turning on the earset Press the Multi button.
Press and hold the Multi button on the
earset for about 7 seconds until the LED
Standby mode
blinks blue.
The unit turns on and the LED starts to blink blue
every 3 seconds.
D Call (audio communication)
1 Call
Operate your mobile phone
Receive a call
Press the Multi button
Note 2 Talk on the phone
Take care not to press and hold the Multi button for
more than 10 seconds, otherwise pairing mode is
entered.
3 Terminate a call
Tip
Press the Multi button
A low/high beep is heard through the earset when it is
turned on.
Turning off the earset
Press and hold the Multi button on the
A Prepare the Bluetooth mobile
earset for about 3 seconds until the LED
phone to be connected
blinks green, then goes off.
Activate the Bluetooth function of the
Bluetooth mobile phone to be connected
to the earset.
For details, refer to the manual supplied with your
Bluetooth mobile phone.
B Turn on the earset
Refer to "Turning on/off the earset" for details.
Note
When the earset is turned off, the current volume level C
Connect between the earset
is stored, except when turned off during charging.
and the Bluetooth mobile
Tip
phone
A high/low beep is heard through the earset when it is
turned off.
Press the Multi button on the earset.
–Introduction Some Bluetooth mobile phones can be operated while
connected to the earset.
To pair the earset with a
Note
Bluetooth mobile phone
In the following cases, connect again between the
earset and the Bluetooth mobile phone.
The earset needs to be paired with a Bluetooth mobile
– the earset is turned off
phone.
Once the earset (DR-BT1) is registered in the mobile phone, – the Bluetooth mobile phone (or its Bluetooth
function) is turned off
there is no need for pairing again.
But in the following cases, pairing is necessary again. – the Bluetooth function on the Bluetooth mobile
• The earset is paired with other Bluetooth equipment. phone and the earset are in sleep mode
• The registration (DR-BT1) in the mobile phone is – Bluetooth connection has terminated
removed.
Refer to the manual supplied with your Bluetooth
mobile phone about Bluetooth connection and the
Note
Bluetooth function.
For details, refer to the manual supplied with your
Bluetooth mobile phone.
D
Call
1
Place the earset and the Bluetooth mobile
To call:
phone within 1m (3 ft) of one another. Use the keypad of your Bluetooth mobile phone to
dial the number, then press the call button. If there is
no sound from the earset, press the Multi button.
Tip
It is possible to call in various ways, depending on the
Bluetooth mobile phone. Refer to the manual supplied
with your Bluetooth mobile phone.
within 1m (3 ft)
– You can call by pressing the Multi button using the
voice-dial function when in standby.
– You can call to the last number dialed by holding
the Volume + or – button (only when using Hands-
free profile).
– You can call a specific number by pressing the
Multi button.
2
While the earset is turned off, press and
To receive a call:
hold the Multi button for about 10 seconds.
When the telephone is ringing, sound will be heard
Keep pressed until the LED blinks blue and green,
through the earset. Press the Multi button on the
indicating pairing mode.
earset.
Sound differs depending on your mobile phone.
– the earset sound
– the mobile phone sound (When using the Bluetooth
function, it may be a specific sound.)
Note
If you pressed the call button on the Bluetooth mobile
phone, some Bluetooth mobile phones may have
handset use priority. In this case, set to talk with the
earset by pressing the Multi button, or by operating
Note
the Bluetooth mobile phone.
Keep pressed while the LED blinks blue for the first 7
For details, refer to the manual supplied with your
of the 10 seconds.
Bluetooth mobile phone.
To terminate a call:
3
Search the earset by the Bluetooth mobile
You can end a call by pressing the Multi button on the
phone.
earset.
In the following cases, audio communication
When the Bluetooth mobile phone detects the earset,
"DR-BT1" will appear in the display of the Bluetooth terminates automatically.
– the end button on the Bluetooth mobile phone is
mobile phone.
pressed
Note
– the recipient hangs up
The pairing mode is canceled after about 60 seconds.
The LED display during audio communication
If the LED returns to blinking blue (every 3 seconds),
repeat from step 1. Earset: Blue blink 3 times (every 3 seconds)
4 –Other operations
Select "DR-BT1" in the list displayed on
your Bluetooth mobile phone.
To adjust the volume
If "DR-BT1" is not displayed, repeat from step 1.
Press VOLUME + or – during connection. A beep
5 corresponding to the selected volume is heard every time
Input the passkey* [0000] when requested
you press either button.
by your Bluetooth mobile phone.
When the volume setting is maximum or minimum, the
If the LED on the earset changes from blinking blue
beep does not sound.
and green to blinking blue slowly (every 3 seconds),
the pairing has completed. VOLUME + VOLUME –
The display of the Bluetooth mobile phone will
usually show that pairing has completed.
* Passkey may also be called the following.
– Pass code, PIN code, PIN number, Password.
Tip
When the sound is low, raise the volume of your mobile
phone. The sound will be clearer.
Note
The volume does not change although the beep sound is
heard when not communicating (only when using the
Headset profile).
Operation of the earset buttons To install the car attachment
The operation of the buttons on the earset varies depending
1
Attach the hook to the rear of the
on the pairing device. Headset profile or Hands-free profile
is used for Bluetooth mobile phone pairing. attachment. Ensure it is the correct way
Refer to the manual supplied with your Bluetooth mobile round. (See illustration.)
phone.
Headset Profile* 1
Multi button VOLUME +/– button
Status Short Press Long Press Short Press Long Press
Off – Power ON – –
Standby – Power OFF – –
Start Voice Dial Cancel Voice Power OFF – –
2
Dial Attach the spacer under the hook firmly
after peeling off the double-sided tape.
Ringing Answer Power OFF – –
Call active End Call Power OFF Adjust volume Mic Mute* 2
by one step
Hands-free Profile* 1
Multi button VOLUME +/– button
Spacer
Status Short Press Long Press Short Press Long Press
Off – Power ON – –
Standby Initiate Voice Power OFF Adjust volume Last number 3
Insert the hook in the vent of the air
Dial by one step Redial
conditioner. Ensure the hook is firmly
Setting up Voice Cancel Voice Power OFF – –
clipped to the fin.
Dial Dial
Ringing Answer Reject – –
Call active End Call Power OFF Adjust volume Mic Mute* 2
by one step
* 1 Some functions may not be supported, depending on
your Bluetooth mobile phone.
Refer to the manual supplied with your Bluetooth mobile
phone.
* 2 The beep sounds every 3 seconds while the microphone
is muted.
4
Dock the Battery charger's belt clip in the
To cancel muting, press the VOLUME + or – button.
attachment.
Indication of the LED
Status Earset
Power on Blue blink for 1 sec.
Power off Green blink for 2 sec.
Standby Blue blink every 3 sec.
Call active Blue blink 3 times every 3 sec.
Pairing mode Blue/Green blink
Tips
Notes
• Use the other hook (L) if the air conditioner is sloped.
• The LED colour of either unit changes from blue to
green when battery charge is low.
• Communication may sometimes not occur, even though
the Multi button on the earset is pressed. In such a case,
the LED double blinks (blue) 3 to 5 times, after which
the earset enters standby mode.
Hook (S)
Failure to communicate will occur in the following cases:
– The earset is not paired with your Bluetooth mobile
Hook (L)
phone.
– The Bluetooth function on your Bluetooth mobile
phone is not activated.
• You can adjust the angle of the attachment by sliding the
rear of the car attachment.
How to use the car
attachment
The car attachment (supplied) can be used to hold the
Battery charger, by installing it in the vent of the air
conditioner of your car.
This is convenient for using while driving.
Standard installation
• Install the hook to face to the side if the fin of the air
Horizontal fin
conditioner is vertical.
3
9 mm ( / 8 in)
17 mm ( 11 / in)
16
(min)
(max)
3 mm ( 1 / in)
8
(max) 7 mm ( 9 / in) g
32
(min)
Vertical fin
• Add another spacer (you will need to modify / fabricate
this yourself) if the car attachment is unstable.
3 mm ( 1 / in) (max)
8
7 mm ( 9 / in) (min)
32
To remove the attachment
1
Push the car attachment back, and push it
3
9 mm ( / 8 in) (min)
gently off the fin.
17 mm ( 11 / 16 in) (max)
Notes
• The car attachment may not be installable. Do not install
the unit by force if installation is difficult. This may
2
Remove the attachment while pressing the
break a fin.
fin.
• Take care not to install or remove the unit by force. A fin
may break.
• If necessary, protect the dashboard and the air
conditioner vent with tape, etc., so as not to damage
anything.
• Install this unit in a place that does not disturb the air bag
function or your driving.
• Be sure to turn off the vent's auto-swing function if your
car has one.
Note
If the attachment is pulled out and catches a fin, it may
damage it.
N Additional information
Precautions
Disposing of the earset
• Avoid using Bluetooth earset with the volume turned up
for an extended period of time. Doing so can damage
For environmental conservation, be sure to remove the your hearing. Listening at high volumes may also cause
built-in rechargeable battery from the unit before you
howling depending on the equipment connected with the
dispose of it, and dispose of the battery appropriately. earset. It is advisable to keep the volume at a moderate
level at all times.
1
Remove the two screws from the rear.
• Do not leave the Bluetooth earset in a location subject to
direct sunlight, heat, moisture or in a parked car.
• Consult local lows and regulations regarding use of the
Bluetooth earset while driving or cycling.
L
• Using the Bluetooth earset may not function on mobile
R
phones, depending on radio wave conditions and location
where the equipment is being used.
• If you experience discomfort after wearing the Bluetooth
2
Push hard around the arrow as illustrated earset, take off the Bluetooth earset immediately.
to unlatch the unit assembly. • Start dialing after connecting the Bluetooth earset to your
mobile phone.
Caring for others
• If you have any questions or problems concerning the
system that are not covered in this manual, please consult
your nearest Sony dealer.
• Be sure to bring the Bluetooth earset and the Battery
3 charger to the Sony dealer when requiring repair work.
Lift the pipe microphone slightly.
Notes on Car attachment
• Make sure this unit is fixed firmly before driving to avoid
an accident or damage.
• Do not handle the Battery charger while driving.
• Do not leave the Battery charger inside a car in high
temperature. This may damage the fins or this unit.
4
Remove the battery holder with battery • Take care that the Bluetooth earset and the Battery
first, then remove the battery from the charger do not fall down while driving and during use.
battery holder.
• The car attachment is only for the Battery charger. Do
not install other device, as it may cause an accident or
Battery holder damage by dropping, etc.
• Be sure to keep the unit out of the reach of children as it
has small parts.
Specifications
General
Bluetooth Compliance: Bluetooth standard Ver. 1.1
5
Remove the connector. Output power: Bluetooth standard Power Class2
Frequency band: 2.4 GHz band
( 2.4000 GHz - 2.4835 GHz )
Max. Communication range:
Line of sight approx. 10 m
Supplied accessory: Battery charger (1), AC power
adaptor (1), Hanger (S) (1),
Car attachment (1)
Bluetooth earset DR-BT1
Supported Bluetooth Profiles:
Headset Profile, Hands-free Profile
Note Power source: DC 3.7 V: Built-in Li-ion
Be careful not to touch the circuit board attached to the rechargeable battery
battery box. Hold the battery box (black plastic box) when Typical Talk time: 7 hours
Typical Standby Time: 160 hours
you remove the battery.
Mass: Approx. 20 g
Receiver
Troubleshooting
Type: Open air, dynamic
Driver unit: 13.5 mm dome type
(CCAW Voice Coil)
Problem Solution Sensitivity: 104 dB/mW
Impedance: 16 Ω at 1 kHz
The recipient voice Check that the power of the Power handling capacity: 50 mW (IEC)
cannot be heard. earset is on. Reproduction frequency range:
And check that the Bluetooth 50 - 20,000 Hz
function on the mobile phone is
Microphone
on.
Type: Flexible pipe microphone
Check the connection between Unit: Electret condenser
the earset and the mobile
Output impedance: Under 2.2 kΩ
phone. Open circuit voltage level: -42 dB (0dB = 1 V/Pa)
Effective frequency range: 100 - 5,000 Hz
Check that the setting to use
with the earset while calling.
Design and specifications are subject to change without
notice.
Check the volume of your
mobile phone and the earset.
Make the pairing of the earset
and your mobile phone again
when the earset is connected to
other Bluetooth products.
Low sound from recipient Turn up the volume of your
mobile phone and the earset.
The recipient cannot hear Cancel the mute of Mic by
or easily hear your voice. pressing the volume button
once when the Mic of the earset
is muted. (Intermittent beep
sound can be heard during
muting.)
Power does not turn on. Recharge the unit.
The unit cannot be turned on
when charging. Unplug the AC
power adaptor from the Battery
charger.
The correspondence If there are the obstacles
distance is short. (The between the earset and the
noise mixes with the Bluetooth mobile phone,
voice.) remove or avoid the obstacles.
If there is equipment that
generates electromagnetic
radiation, etc., such as a
wireless LAN, other Bluetooth
equipment, a microwave oven
nearby, move away.
Pairing can not be done. Pair the units by bringing the
earset and the mobile phone
close together.
The earset cannot be Dock the earset with the
charged. Battery charger so that the LED
turns green.
When the contact terminal on
the earset and the contact pin
on the Battery charger are dirty,
wipe them lightly with a soft
dry cloth.