Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for TURBRO Neighborhood GH7500
Summary of Contents for TURBRO Neighborhood GH7500
- Page 1 GARAGE HEATER MODEL: GH7500 HARDWIRED INSTALLATION REQUIRED THIS HEATER MUST BE GROUNDED AND HARDWIRED TO A PROPERLY SIZED CURRENT PROTECTION CIRCUIT BREAKER IN ACCORDANCE WITH THE (US) NATIONAL ELECTRIC CODE AND LOCAL CODES. KEEP THIS USER MANUAL FOR FUTURE REFERENCE.
-
Page 2: Table Of Contents
CONTENTS ..............WARRANTY REGISTRATION ................SAFETY INSTRUCIONS ..........ELECTRICAL SAFETY INFORMATION ................SPECIFICATIONS ............... LOCATIONG THE HEAER ..................INSTALLATION ..............MOUTING THE BRACKET ........HANGING THE HEATER IN THE BRACKET ..............CONNECTING THE POWER ................ADJUSTING AIR FLOW .................... OPERATING .............. -
Page 3: Warranty Registration
To express our appreciation, we are giving you a warranty extension. All you need to do is to register your new product at https://www.turbro.com/warranty. After registration, you'll get a 1-year extension on the 1-year manufacturer warranty for a total of 2 years. It's that easy! Tip for First-Time Use When using this heater for the first time, or after a long period of storage. -
Page 4: Electrical Safety Information
• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater. • To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use it on soft surfaces, like a bed, where openings may become blocked. -
Page 5: Locationg The Heaer
LOCATING THE HEATER WARNING • FOR INDOOR USE ONLY, PLACE THE HEATER IN A DRY LOCATION FREE OF GASOLINE, PAINT, FLAMMABLE LIQUIDS OR COMBUSTIBLE DUST OR MATERIALS. • DO NOT USE EXTENSION CORDS • Install heater out of traffic areas, maintaining the clearances stated in Figure 2. Ensure that the airflow is not restricted or obstructed by any items, and it should gently sweep exposed walls instead of blowing directly onto them. -
Page 6: Installation
INSTALLATION MOUNTING THE BRACKET Tools Required (not included) • Electric screwdriver • Tape measure • Electric power drill Hardware Required (included) Part Descri ption Quantity 3/8” Diameter Lag Bolt Washer M10 Expansion Bolt Locate a ceiling joist or other firm structural element or support to mount the heater and point at the desired direction of airflow. -
Page 7: Hanging The Heater In The Bracket
B. Mount the bracket with the concrete ceiling. Refer to Figures 4c and 4d. 1. Drill a 0.47” pilot hole in the ceiling joist for the expansion bolt(s). 2. Place the bolt(s) and washers as shown in the Figures 4c or 4d. Figure 4c: For Single-Bolt Mounting (center bracket hole only). -
Page 8: Connecting The Power
CONNECTING THE POWER Terminal station Temperature sensor Motor AC 240V/60Hz Capacitor overheat Control panel Electronic circuit board ACL1 ACL2 Wiring diagram WARNING: This appliance must be grounded. WARNING: This appliance must connect to a current protection circuit or device at 50 Amp or less before being connected to power supply! NOTE: All wiring must be carried out by a Certified Electrician and must be in accordance with national and local electrical codes in the United States. - Page 9 CONDUIT CONDUIT CONNECTOR 3ft. If Heater is to min. be turned and wire is inside conduit. FLEXIBLE FLEXIBLE CONDUIT CONDUIT CONNECTOR If Heater is to be connected with NM Cable. FLEXIBLE FLEXIBLE NM CABLE NM CABLE CONNECTOR (use per electircal codes) If Heater is to be connected with Flexible...
-
Page 10: Adjusting Air Flow
ADJUSTING AIR FLOW WARNING: To prevent electric shock, disconnect the power to the heater at the main service box before attempting to adjust the louvers. 1. Swivel the unit If the heater is mounted on a single center lag bolt (see Figure 4a / 4c), you can adjust the entire heater and bracket assembly by turning it left or right. -
Page 11: Operating
OPERATING WARNING: The heater must be properly installed before use. Control Panel Power Heater LCD Screen Down Timer When the heater is plugged in, all buttons will flash and the screen will display the environment temperature and heating stage ‘OFF’ alternatively every 15 seconds. 1. - Page 12 4 & 5. Up & Down Button • Press the Up & Down button to adjust the temperature setting between 50°F - 95°F(10°C - 35°C). See the table for detailed temperature setting instruction. NOTE: Please note that the Up & Down button functions exclusively when the heating function is on. Fahrenheit 50°F 51°F...
- Page 13 Remote Control The remote control can be used up to 19.7 feet (6 meters) away from the heater, so long as there are no obstructions between the remote control and the heater. The remote can control all the settings as the control panel does. Power Heater Down...
-
Page 14: Care And Maintenance
2. Temperature sensor is loosened the status of your settings. or damaged. 2. Check the temperature sensor, re-tighten it. If it still does not work, contact turbro service team. DISCONNECT THE POWER! 1. Check the temperature sensor, and re- 1. Temperature sensor is loosened. -
Page 15: Warranty Information
WARRANTY INFORMATION TURBRO provides a 1-year limit for TURBRO Heater, from the date of purchase, subject to the following conditions and limitations. WHAT IS COVERED? • Any alteration or misuse of the product will nullify this warranty. • This warranty is non-transferable and is effective for the original buyer from the authorized seller only.
Need help?
Do you have a question about the Neighborhood GH7500 and is the answer not in the manual?
Questions and answers