Hans Grohe LavaPura Uno Shower Toilet E 305 22406007 Instructions For Use/Assembly Instructions
Hans Grohe LavaPura Uno Shower Toilet E 305 22406007 Instructions For Use/Assembly Instructions

Hans Grohe LavaPura Uno Shower Toilet E 305 22406007 Instructions For Use/Assembly Instructions

Advertisement

Quick Links

EN
2
Instructions for use / assembly instructions
LavaPura Uno Shower Toilet E 305
22406007

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LavaPura Uno Shower Toilet E 305 22406007 and is the answer not in the manual?

Questions and answers

Summary of Contents for Hans Grohe LavaPura Uno Shower Toilet E 305 22406007

  • Page 1 Instructions for use / assembly instructions LavaPura Uno Shower Toilet E 305 22406007...
  • Page 2: Table Of Contents

    Contents Safety Instructions Tools and materials required Dimensions Technical Specifications Sketch List of Materials Installation of the ceramic toilet Installation of the remote control Preparation before Use Automatic lid opening/closing Functional Buttons of Main Unit Usage of Remote Control Maintenance and Care of Main Unit Maintenance and Care of Spray Nozzle Diatoms replacement When the electricity and water supply is cut-off...
  • Page 3 Important Safeguards When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following: 1.The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
  • Page 4: Safety Instructions

    Important Safety Instructions CAUTION – Indicates that failure to follow the instruction may cause body injury or property damage. 1. Do not install or use the product in wet places as steam room etc. 2. It is recommended to use water-proof electrical outlet which should be lnstalled in the place where is not easily got wet.
  • Page 5: Tools And Materials Required

    Tools and Materials Required (not supplied) Adjustable wrench × 2 Measuring tape Teflon tape Utility knife Drill Sorts of screwdrivers Glass cement gun Glass cement Marking pen Level Dimensions 448mm 462mm 324mm Top view Finished wall 742mm Finished floor 305 mm To outlet hole Notes: 1.
  • Page 6: Technical Specifications

    Items 22406007 AC 230V 50Hz/60Hz 200W 742 mm (length) × 462 mm (width) × 490 mm (height) 50kg...
  • Page 7: Sketch

    Sketch Sketch Remote control Remote control Remote control hanger Remote control hanger Front washing Front washing Rear washing Rear washing Seat Seat Seated sensing area Seated sensing area Spray nozzle Spray nozzle ON/OFF ON/OFF Manual flushing button Manual flushing button Deodorization window Deodorization window Angle valve...
  • Page 8: List Of Materials

    List of Materials Remote control Main unit Sealing flange Alignment hole cardboard Instructions for use / assembly instructions Angle valve Manual...
  • Page 9: Installation Of The Ceramic Toilet

    Installation of the ceramic toilet Precautions before installation: Minimum dynamic operating water pressure: 0.08 MPa or more (flowing at 14 L/min or more). The flushing effect may be affected if failed to meet this pressure. Tips: If no water pressure tester is available, you may refer to the following method. Mating water inlet pipe Mating angle valve Water storage barrel...
  • Page 10 Ceramic drain outlet (Align the arrows on the labels at both sides of the bottomof the ceramic with the center Sealing flange line of the drain outlet) Floor outfall Tips: It is suggested to lift and open the seat by two persons since the one-piece toilet is heavy. 4.
  • Page 11 . Application of the glass cement Apply high-quality mildew-proof glass cement around the lower edge of the toilet. Glass cement Tips: Clean the garbage and other dirt on drain outlet; and when installing the toilet,make sure the drain outlet of the toilet drain and the floor outfall are installed in place.
  • Page 12: Installation Of The Remote Control

    Installation of the remote control Do not install and use this product in a damp environment. Do not place it in a place where it is likely to be damped with water. 1. Installation of remote control hanger ① Press the remote control hanger upright against the pre-installation area on the wall,and mark the positions of the two mounting holes on the wall with the marking pen.
  • Page 13: Preparation Before Use

    Preparation before Use 1. Turn on the angle valve To check the tightness of the pipe connections and make sure that there is no water leakage, turn the angle valve counterclockwise to adjust the opening to the maximum. Water inlet angle valve 2.
  • Page 14: Automatic Lid Opening/Closing

    Automatic lid opening/closing function If you are purchasing an electronic toilet with automatic lid opening/closing function, it has the feature of automatically opening/closing the lid. ( The auto open&close function of lid is set to off by default. For the first use, you need to press the remote control's auto switch"...
  • Page 15: Functional Buttons Of Main Unit

    Functional Buttons of Main Unit Front washing Rear washing Indicator light ON/OFF Operation instructions of buttons: 1. When sitting on the seat, short press the feminine/rear washing button to activate the feminine/rear washing function. 2. When the feminine/rear washing function is being activated, short press the ON/OFF button to shut down the function.
  • Page 16: Usage Of Remote Control

    Usage of Remote Control Rear washing Open/close seat Setting Stop (Buttons are provided on the side of the product) Warm Flushing wind Low battery "ON/OFF" status display Adjust nozzle position 3-level status display light Adjust water pressure Cold and hot washing Mobile Massage cleaning washing...
  • Page 17 Rear/front washing Initial position When in a seated status, The level-2 button appears when water Once pressing the nozzle The feminine/rear washing spraying begins, and the following is operable: position/water pressure adjusting starts,and the nozzle stretches -Mobile washing/cold and hot washing/ button,the Level-3 status indicator out, and starts to spray.
  • Page 18 Initial position Warm wind When in a seated status, The warm wind function is activated to start blowing. The level-2 button does not appear Before the warm wind ends (within 300 seconds),the user may stop the warm wind by pressing the warm wind button or the stop button to stop the warm wind.
  • Page 19 Setting Press the setting The Level-3 button Once pressing the seat Once pressing the night light/ buttonto enter the appears,and the following temperature/water seating deodorization/ Setting mode. is operable: temperature/warm wind automatic lid opening/ - Adjust the seat temperature/ temperature button,the auto flushing button, water temperature/warm Level-3 indicator lightin...
  • Page 20 Setting Press the setting The Level-3 button Long press the user When in the off-seat buttonto enter the appears,and the mode 1 or 2: status,short press the Setting mode. following is operable: The screen backlight nozzle cleaning buttonto flashes three times, executethe nozzle - User settings 1 and 2 to save the current water...
  • Page 21: Maintenance And Care Of Main Unit

    Maintenance and Care of Main Unit 1. Cut off the power: Please cut off the power before maintaining the main unit. 2. Wipe with a soft rag: Please wipe the dirty area with a wrung-out soft rag. 3. Safety self-inspection: Please reconnect the power after wiping. 4.
  • Page 22: Diatoms Replacement

    Diatoms replacement 1. As shown in the figure, press the deodorization set to pop up the deodorization box; 2. Take out the deodorization box, disassemble the deodorization box with your hands, and replace the diatoms; Deodorization cover Deodorization set Diatoms Deodorization box 3.
  • Page 23: When The Electricity And Water Supply Is Cut-Off

    When the electricity and water supply is cut-off 1. How to flush the toilet during interruption of power supply: Press the manual flushing button (Press and hold for more than 4 seconds) to flush it. Manual flushing button (Press and hold for more than 4 seconds) 2.
  • Page 24: Fault Analysis And Solution

    Fault Analysis and Solution Problem Cause Solution The water inlet hose buckles to Solve the buckling cause blockage Turn on the fill valve The fill valve is off No flushing Water supply is cut off Wait for water supply restoration Filter blockage Replace the filter The water inlet hose buckles to...

Table of Contents