Triplett LVPRO10 User Manual
  1. Manuals
  2. Brands
  3. Triplett Manuals
  4. Measuring Instruments
  5. LVPRO10
  6. User manual

Triplett LVPRO10 User Manual

Tdr/cable tester
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
User Manual
LVPRO10
TDR/Cable Tester
Contents
VII.POE Mode
VIII.Tone Mode
8.2 LVPRO10 Receiver ----------------------------------------------------------------------- 16
9.1 Setting the NVP to a Specified Value ------------------------------------------------ 18
9.2 Determining a Cable's Actual NVP ---------------------------------------------------- 19
3
3
4
4
5
6
6
12
14
15
15
19
19
19
20
20
20
20
20
2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LVPRO10 and is the answer not in the manual?

Questions and answers

Related Manuals for Triplett LVPRO10

Summary of Contents for Triplett LVPRO10

  • Page 1: Table Of Contents

    VII.POE Mode VIII.Tone Mode 8.1 Tone Mode Display 8.2 LVPRO10 Receiver ----------------------------------------------------------------------- 16 IX. Calibrating Length Measurements (Only for test mode) ---------------------------- 18 9.1 Setting the NVP to a Specified Value ------------------------------------------------ 18 9.2 Determining a Cable’s Actual NVP ---------------------------------------------------- 19 X.

  • Page 2: Overview

    III. Safety Information To avoid fire, electric shock or personal injury, please follows: The Triplett LVPRO10 is a handheld TDR cable tester, suitable for copper cables (CAT 5E Do not open the casing, there is no any user-serviceable part inside.

  • Page 3: Display Features (Lvpro10)

    VI. Testing Mode V. Display Features (LVPRO10 Main Unit) 6.1 Testing Twisted-Pair Cabling 6.1.1 Cabling Test (1) Turn on the tester, and set the knob to "TEST", then press "PORT" to select RJ45 10 11 port. (2) Connect tester and wire map adapter to the cabling, the test runs continuously until you change modes or turn the tester off.
  • Page 4 6.1.2.4 Crossed Pairs 6.1.2.2 Short on Twisted Pair Cabling Figure 6.5 shows that 1, 2 and 3, 6 are crossed. The pin numbers flash to indicate the fault. Figure 6.3 shows a short between wires 5 and 6, the shorted wires flash to indicate the Detection of crossed wires requires a far-end adapter.
  • Page 5 6.1.2.8 Voltage Detection 6.1.2.6 Ethernet Port Detected Figure 6.9 shows that the tester detects cable voltage. Figure 6.7 shows that the tester detects Ethernet port. If the measured cable is live and its voltage is greater than or equal to 10V, the tester The tester cannot measure the length if the port does not produce reflections.

  • Page 6: Testing Coaxial Cabling

    6.1.2.11 Connecting to Telephone Networks in Bus Topologies 6.1.2.10 Connecting to Telephone Networks Wired in Star Topologies Telephone cables wired in a bust topology (Figure 6.12) connect the wall outlets in series. Telephone cables wired in a star topology (Figure 6.11) are connected together at a bridge In this topology, you measure the length from the last outlet to the wire map adapter.
  • Page 7 6.2.2 Typical Testing Results 6.2.2.4 Voltage on Coaxial Cabling Figure 6.17 shows that the symbol “ ” appears if the coaxial cable is live and its voltage 6.2.2.1 Results for a Good Coaxial Cable is greater than or equal to 10V. Figure 6.14 shows a good coaxial cable 63.2m and terminated with far-end adapter Figure 6.14 Coaxial Results Figure 6.17 Voltage on Coaxial Cabling...

  • Page 8: Tone Mode Display

    8.1 Tone Mode Display 8.2.1 Features With the support of LVPRO10 tester, The receiver can achieve multiple functions such as (1) Turn on the tester, then set the knob to “SCAN”. In tone mode, the default display is locating and isolating cables by adjusting sensitivity, twisted-pair cable tracking, coaxial shown in Figure 8.1.a.

  • Page 9: Calibrating Length Measurements (Only For Test Mode)

    (1) Connect LVPRO10 tester to the line. receptacle is greater than 40V (AC), the receiver makes beep sound and the NCV (2) Set LVPRO10 tester to “SCAN” mode, press “POR T” to select RJ45 port. Short indicator light flashes synchronously.

  • Page 10: Determining A Cable's Actual Nvp

    9.2 Determining a Cable’s Actual NVP XIII. Other functions (1) Hold down “ ”, “ ” and “ ” at the same time to enter NVP setting mode. 13.1 Low battery indication (2) To set the NVP of coaxial port, please press “PORT. Please replace the battery when the symbol “...
  • Page 11 Triplett / Jewell Instruments extends the following warranty to the original purchaser of these goods for use. Triplett warrants to the original purchaser for use that the products sold by it will be free from defects in workmanship and material for a period of (1) one year from the date of purchase.

Table of Contents