Table of Contents
Advertisement
Initial installation
Follow the steps below one by one when using the Monitor for the first time. Some steps may not be necessary
depending on your Monitor installation and connection.
Plug the AC cord into the AC inlet of the main unit.
Plug the AC cord into the AC outlet.
•
Place the Monitor close to the AC outlet, and keep the
power plug within reach.
Press
(JOG-KEY) on the Monitor.
Terminal Diagram
Monitor (Rear)
AC Inlet
Bundle the cables into
cable tie.
Press cable tie clip (1)
and pull out cable tie (2)
completely to release.
乙太網絡
(LAN)
耳機
(10/100 BASE-T)
(EAR PHONE)
HDMI 3
光纖數位聲音輸出
(eARC/ARC)
(OPTICAL DIGITAL
AUDIO OUTPUT)
Viewing E-Manual
Viewing the Built-in Operation Manual
Displays the built-in operation manual on the
screen. You can read information about how to
use this device.
The internet connection will be required.
1
Press
(HOME) to display the HOME screen,
/
press
to select "Manual", and then press
確定 (ENTER)/OK.
2
When you select contents, its page will be
displayed.
Run the initial installation.
• Follow the guide on the Monitor screen to set
the settings.
Instruction for using AV IN.
Requires RCA jack conversion.
Buy the service parts (QCNWGA252WJPZ).
Side terminal
Yellow
(Video)
White
(Audio L)
影音輸入
1-GND
Red
2-Audio R
(Audio R)
3-Audio L
Game console,
4-Video
DVD player, etc.
僅供售後服務
使用
(FOR SERVICE
ONLY)
影音輸入
(AV IN)
USB
(DC5V 0.5A Max)
HDMI 1
JOG-KEY
HDMI 2
HDMI 4
2
Appendix
Troubleshooting
The problems described below are not always caused by malfunctions. Check the Monitor again before having the
Monitor serviced.
P
o r
b
e l
m
•
No power.
Video
•
Remote control unit does
Audio L
not operate.
Audio R
•
No picture.
•
No sound.
Clearing the password
If you forget the password, clear the password using the following procedure.
1
From the Dashboard, select "Settings" > "System" > "About" > "Reset" > "Factory reset", and then press
確定 (ENTER)/OK.
2
When you perform a reset, the Monitor will be returned to the factory preset values, and you need to set the
password again.
NOTE
• The default PIN is "1234".
• As a precautionary measure, make a note of your password, and keep it in a safe place.
DISCLAIMERS
• This SHARP device facilitates the access to content and services provided by third parties. The content and
services accessible via this device belong to and may be proprietary to third parties. Therefore, any use of such
third party content and services must be in accordance with any authorization or terms of use provided by such
content or service provider. SHARP shall not be liable to you or any third party for your failure to abide by such
authorization or terms of use. Unless otherwise specifically authorized by the applicable content or service provider,
all third party content and services provided are for personal and non-commercial use; you may not modify, copy,
distribute, transmit, display, perform, reproduce, upload, publish, license, create derivative works from, transfer or
sell in any manner or medium any content or services available via this device.
• SHARP is not responsible, nor liable, for customer service-related issues related to the third party content or
services. Any questions, comments or service-related inquiries relating to the third party content or service should
be made directly to the applicable content or service provider.
You may not be able to access content or services from the device for a variety of reasons which may be unrelated
to the device itself, including, but not limited to, power failure, other Internet connection, or failure to configure your
device properly. SHARP, its directors, officers, employees, agents, contractors and affiliates shall not be liable to
you or any third party with respect to such failures or maintenance outages, regardless of cause or whether or not it
could have been avoided.
• ALL THIRD PARTY CONTENT OR SERVICES ACCESSIBLE VIA THIS DEVICE IS PROVIDED TO YOU ON AN
"AS-IS" AND "AS AVAILABLE" BASIS AND SHARP AND ITS AFFILIATES MAKE NO WARRANTY OR
REPRESENTATION OF ANY KIND TO YOU, EITHER EXPRESS OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, ANY WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT, FITNESS FOR A
PARTICULAR PURPOSE OR ANY WARRANTIES OF SUITABILITY, AVAILABILITY, ACCURACY,
COMPLETENESS, SECURITY, TITLE, USEFULNESS, LACK OF NEGLIGENCE OR ERROR-FREE OR
UNINTERRUPTED OPERATION OR USE OF THE CONTENT OR SERVICES PROVIDED TO YOU OR THAT
THE CONTENT OR SERVICES WILL MEET YOUR REQUIREMENTS OR EXPECTATIONS.
• SHARP IS NOT AN AGENT OF AND ASSUMES NO RESPONSIBILITY FOR THE ACTS OR OMISSIONS OF
THIRD PARTY CONTENT OR SERVICE PROVIDERS, NOR ANY ASPECT OF THE CONTENT OR SERVICE
RELATED TO SUCH THIRD PARTY PROVIDERS.
• IN NO EVENT WILL SHARP AND/OR ITS AFFILIATES BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL, PUNITIVE, CONSEQUENTIAL OR OTHER DAMAGES, WHETHER
THE THEORY OF LIABILITY IS BASED ON CONTRACT, TORT, NEGLIGENCE, BREACH OF WARRANTY,
STRICT LIABILITY OR OTHERWISE AND WHETHER OR NOT SHARP AND/OR ITS AFFILIATES HAVE BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
- 11
- 12
P
o
s
s
b i
e l
S
l o
t u
o i
n
•
Check if you pressed 電源 (POWER) on the remote control unit.
•
Is the AC cord disconnected?
•
Has the power been turned on?
•
Are batteries inserted with polarity ( e , f ) aligned?
•
Is connection to other components correct?
•
Is connection to other components correct?
Advertisement
Table of Contents
