Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Traxxas STAMPEDE 4x4 BRUSHLESS
Summary of Contents for Traxxas STAMPEDE 4x4 BRUSHLESS
- Page 1 MODEL 67154-4 owner s manual ’...
- Page 2 BL-2s™ electronic speed control, TOOLS, SUPPLIES, AND REQUIRED EQUIPMENT Stampede 4X4 Brushless is built for high-speed action. The pre- Quick Start installed Extreme Heavy Duty Upgrade Kit offers a full complement This manual is designed with a Quick...
-
Page 3: Before You Proceed
Traxxas service needs. Maintenance and replacement identified by the icons below. Be sure to read them! To-Win, Stampede 4X4, BL-2s, parts may be purchased directly from Traxxas by phone or online and ProGraphix are trademarks An important warning about personal safety or avoiding at Traxxas.com. -
Page 4: Safety Precautions
SAFETY PRECAUTIONS All of us at Traxxas want you to safely enjoy your new model. Operate • Insulate the Wires: Always insulate exposed wiring with heat shrink your model sensibly and with care, and it will be exciting, safe, and tubing to prevent short circuits. - Page 5 • ONLY use a Traxxas iD charger to charge Traxxas iD batteries. identifying the battery type and specifications. ALWAYS use a ONLY use a Lithium Polymer (LiPo) balance charger with a Traxxas iD charger to charge Traxxas iD batteries.
- Page 6 SAFETY PRECAUTIONS (continued from previous page) • While charging or discharging, ALWAYS place the battery (all • DO NOT disassemble, crush, short circuit, or expose the batteries to types of batteries) in a fire retardant/fire proof container and on flame or other source of ignition. Toxic materials could be released. a non-flammable surface such as concrete.
-
Page 7: Tools, Supplies, And Required Equipment
*Battery and charger style are subject to change and may vary from images. REMOVING AND INSTALLING THE BODY Your Stampede 4X4 Brushless includes an innovative latching system for securing the body to the chassis. To remove the body for chassis access: 1. - Page 8 ANATOMY OF THE STAMPEDE 4X4 BRUSHLESS Shock Battery Hold-Down Battery Compartment Steering Block Caster Block Rear Camber Link Drive Shaft Traxxas High-Current Front Camber Link Connector Rear Shock Tower Receiver Box Front Bumper Spur Gear Front Shock Tower Rear Bumper...
-
Page 9: Quick Start: Getting Up To Speed
QUICK START: GETTING UP TO SPEED The following guide is an overview of the procedures for getting your model running. Look for the Quick Start logo on the bottom corners of Quick Start pages. The Quick Start Guide is not intended to replace the full operating instructions 1. - Page 10 TRAXXAS TQ 2.4GHz RADIO SYSTEM INTRODUCTION power more efficiently than mechanical speed controls so that Your model includes the TQ 2.4GHz transmitter. When powered the batteries run longer. An electronic speed control also has Applying the Decals on, the TQ 2.4GHz will automatically locate and lock onto an...
- Page 11 TRAXXAS TQ 2.4GHz RADIO SYSTEM Resistance - In an electrical sense, resistance is a measure of how 2-channel radio system - The TQ radio system, consisting of an object resists or obstructs the flow of current through it. the receiver, the transmitter, and the servos. The system uses To prevent loss of radio range, When flow is constricted, energy is converted to heat and is lost.
- Page 12 TRAXXAS TQ 2.4GHz RADIO SYSTEM MODEL WIRING DIAGRAM Your model is equipped with the Traxxas TQ 2.4GHz transmitter. BL-2s Wiring Diagram The transmitter has two channels: Channel one operates the Motor Antenna steering, and channel two operates the throttle. The receiver (BL-2s 3300) inside the model has three output channels.
- Page 13 Refer to the select. Traxxas recommends you choose a genuine Traxxas EZ-Peak iD Troubleshooting section on page 17 for more information on charger for safer charging and maximum battery life and performance.
- Page 14 Secure, long-lasting, and easy to separately) to automatically recognize connected battery grip, the Traxxas connector is engineered to extract all the power your packs and optimize the battery has to give. charge settings for the battery.
- Page 15 TRAXXAS TQ 2.4GHz RADIO SYSTEM RADIO SYSTEM CONTROLS • In order for the transmitter and receiver to bind to one another, the receiver in the model must be turned on within 20 seconds Remember, always turn the of turning on the transmitter. The transmitter LED will flash fast transmitter on first and off red, indicating a failure to link.
- Page 16 TRAXXAS TQ 2.4GHz RADIO SYSTEM Throttle reversing procedure: 6. When looking down at the Note: Throttle reversing is often times unnecessary on electric model, the front wheels Using Reverse: While driving, models, as issues with the throttle can usually be solved by...
- Page 17 TRAXXAS TQ 2.4GHz RADIO SYSTEM Higher Speeds Require Greater Distance TQ 2.4GHz Binding Instructions The faster you drive your model, the more quickly it will near the For proper operation, the transmitter and receiver must be Failsafe limit of radio range. At top speeds, models can cover anywhere electronically ‘bound.’...
-
Page 18: Adjusting The Electronic Speed Control
1. Turn the transmitter off. transmission on high-traction surfaces. 2. Hold both MENU and SET. 7. To turn the BL-2s off, press the EZ-Set button until the LED turns 18 • TRAXXAS 3. Turn the transmitter on. off (.5 seconds). - Page 19 ADJUSTING THE ELECTRONIC SPEED CONTROL BL-2s Profile Selection 4. The LED will blink and then turn solid The speed control is factory set to Profile #1 (100% forward, brakes, and reverse). green (Low-Voltage Detection ACTIVE) or Patented Training Mode To disable reverse (Profile #2) or to allow 50% forward and 50% reverse (Profile #3), red (Low-Voltage Detection DISABLED).
-
Page 20: Driving Your Model
RUNNING IN WET CONDITIONS result in poor performance and broken parts. Take care of your Your new Traxxas model is designed with water-resistant features model so that you can enjoy it for a long time to come. to protect the electronics in the model (receiver, servos, electronic •... - Page 21 Do NOT use pressure washer or other • The Traxxas TQ 2.4GHz transmitter is not water resistant. Do not high-pressure water. Avoid directing water into the bearings, subject it to wet conditions such as rain.
- Page 22 DRIVING YOUR MODEL RECEIVER BOX: SETTING UP THE ANTENNA MAINTAINING A WATERTIGHT SEAL To set up the receiver antenna, To prevent loss of radio range, Removing and Installing Radio Gear remove the set screw with the Antenna do not kink or cut the black wire, The unique design of the receiver box allows the removal and included 1.5mm wrench.
-
Page 23: Adjusting Your Model
#1952X. These position 4 or 5 on the can add or remove 1.5° toe gears. Stampede 4X4 Brushless makes improper gear mesh virtually suspension arms. per side, for a total of 0 to 3 impossible. A factory installed fixed gear adapter helps set the degrees per side. - Page 24 ADJUSTING YOUR MODEL Centering Your Servo If you are worried that you might be over-geared, check the Gearing Compatibility Chart: The chart below shows If the trim controls on your transmitter seem off, you may need to temperature of the battery pack and motor. If the battery is extremely recommended gear combination re-center your servo.
- Page 25 Most will affect the overall width and the point for the slipper clutch Only use silicone oil in the differentials. Traxxas offers various suspension geometry of the model. The offsets and dimensions in this model, remove the viscosity oil between SAE 10,000W, and 500,000W (see your parts designed into the model’s wheels are intentional;...
- Page 26 ADJUSTING YOUR MODEL Rear differential: Rear Differential Removal 1. Remove the two 3x20mm button-head screws that secure the top bumper mount to the differential case. 2. Turn the chassis over and remove the two 3x12mm countersunk 3x20 BCS crews that hold the bumper/skid plate to the bulkhead. The two front screws do not need to be removed.
-
Page 27: Maintaining Your Model
If the bottom of the shock is leaking, then it condition of the batteries. is time for a rebuild. The Traxxas rebuild kit for two shocks is 8. Check for any loose screws in the chassis structure part #2362. - Page 28 MAINTAINING YOUR MODEL Suspension and slipper clutch assembly removal Your model was designed with ease of disassembly in mind. The entire front and rear suspension assemblies can be removed from the chassis fully intact with the removal of only a few screws. Refer to the exploded views included in the your model’s Service Support Guide for complete assembly diagrams.
- Page 29 RUSTLER 4X4 • 29...
- Page 30 ’ 6250 TRAXXAS WAY, MCKINNEY, TEXAS 75070 1-888-TRAXXAS 230908 67154-4-OM-EN-R00...