Index Warning, Caution ...English-1 Registration Information ...English-2 Recommended use ...English-4 Contents ...English-6 Quick Start ...English-7 Controls ...English-9 Speciﬁ cations ...English-12 Features ...English-13 Troubleshooting ...English-14 TCO Displays 5 ...English-15 Manufacturer’s Recycling and Energy Information ...English-16...
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Registration Information Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1. FCC Information Use the attached speciﬁ...
The product is intended to be connected to a computer and is not intended for the display of television broadcast signals. Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy, Norway, Spain, Sweden, U.K.
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for the display to warm up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen.
Contents Your new NEC monitor box* should contain the following: • AccuSync monitor • Power Cord • Video Signal Cable (Mini D-SUB 15 pin to Mini D-SUB 15 pin) • Stand Base • Stand Neck • Setup Manual Power Cord* Setup Manual Remember to save your original box and packing material to transport or ship the monitor.
Quick Start To attach the Stand neck and Base Stand to the LCD Stand: 1. Attach the Stand neck to the monitor. And then, attach the Base Stand to the Stand. The locking tabs on the Base Stand should ﬁ t into the hole on the Stand (Figure 1). To connect the LCD monitor to your system, follow these instructions: 1.
Tilt Grasp top and bottom sides of the monitor screen with your hands and adjust the tilt as desired (Figure TS.1). NOTE: Handle with care when tilting the monitor screen. Repacking Remove stand base and stand neck for repacking. 1. Disconnect all cables. 2.
Controls OSD (On-Screen Display) control buttons on the front of the monitor function as follows: 1. Basic function at pressing each key Button At No OSD showing Showing OSD. At OSD showing Go to Adjustment stage. (Icon selection stage) At OSD showing Go to Icon selection stage.
BRIGHTNESS Adjusts the overall image and background screen brightness. To enter the ECO MODE, press the “1!2/RESET” button. ECO MODE OFF: Set brightness variable from 0% to 100%. ECO MODE1: Set brightness 70%. This setting automatically adjusts brightness within a power consumption range that meets ENERGY STAR 5 requirements.
OSD TURN OFF The OSD control menu will stay on as long as it is in use. In the OSD Turn OFF submenu, you can select how long the monitor waits after the last touch of a button to shut off the OSD control menu. The preset choices are 10 - 120 seconds by 5 seconds step.
60 Hz to 75 Hz 1440 x 900* at 60 Hz 1680 x 1050* at 60 Hz 1920 x 1080 at 60 Hz... NEC DISPLAY SOLUTIONS cites recommended 521.3 mm/20.5 inches 293.2 mm/11.5 inches AC 100-240 V ~ 50/60 Hz 0.45 - 0.25 A 566.0 mm (W) x 395.1 mm (H) x 190.0 mm (D)
- conversion factor is based on OECD publication of global CO2 emissions 2008 Edition). This monitor has a manufacturing carbon footprint of approximately 26.0 kg. Note: The manufacturing and operating carbon footprints are calculated by a unique algorithm developed exclusively by NEC for its monitors.
TCO Displays 5 This display is designed for both you and the planet! TCO CertiÞ ed is a third party veriÞ ed program, where every product model is tested by an accredited impartial test laboratory. TCO CertiÞ ed represents one of the toughest certiÞ cations for displays worldwide.
Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.