Table of Contents
Advertisement
Quick Links
CHIP WARMERS
MODELS:
500-CW
700-CW
500-CW-EX
700-CW-EX
For additional information on WITTCO or to locate an authorized parts
and service provider in your area, visit our website at
WITTCO FOOD SERVICE EQUIPMENT
DIVISION OF ITW FOOD EQUIPMENT GROUP, LLC
www.wittco.com
OPERATION MANUAL
(New 2014)
(New 2014)
©
2014 Wittco Foodservice Equipment
INSTALLATION &
www.wittco.com
7737 NORTH 81 STREET
MILWAUKEE, WI 53223
F-41160 (12-14)
Advertisement
Table of Contents
Related Manuals for Wittco 500-CW-EX
Summary of Contents for Wittco 500-CW-EX
- Page 1 700-CW 500-CW-EX (New 2014) 700-CW-EX (New 2014) For additional information on WITTCO or to locate an authorized parts and service provider in your area, visit our website at www.wittco.com WITTCO FOOD SERVICE EQUIPMENT 7737 NORTH 81 STREET DIVISION OF ITW FOOD EQUIPMENT GROUP, LLC MILWAUKEE, WI 53223 www.wittco.com...
-
Page 2: Important For Your Safety
500-CW, 700-CW, 500-CW-EX, 700-CW-EX CHIP WARMER F-41160 (12-14) IMPORTANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL ELECTRICAL EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START- UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. -
Page 3: Table Of Contents
500-CW, 700-CW, 500-CW-EX, 700-CW-EX CHIP WARMER F-41160 (12-14) TABLE OF CONTENTS IMPORTANT FOR YOUR SAFETY ........1 GENERAL . -
Page 4: General
F-41160 (12-14) GENERAL INTRODUCTION Wittco Chip Warmers are produced with quality workmanship and material. Proper installation, usage, and maintenance of your warmer will result in many years of satisfactory performance. It is suggested that you thoroughly read this entire manual and carefully follow all of the instructions provided. -
Page 5: Installation Specific To Models 500-Cw & 700-Cw
500-CW, 700-CW, 500-CW-EX, 700-CW-EX CHIP WARMER F-41160 (12-14) INSTALLATION SPECIFIC TO MODELS 500-CW & 700-CW ACCESS PANEL POSITIONING: SCOOP HOLDER INSTALLATION: Ensure that top Baffle notches The Chip Scoop Holder will secure up to are over carriage bolts. a 6“ wide scoop. -
Page 6: Electrical Requirements
500-CW, 700-CW, 500-CW-EX, 700-CW-EX CHIP WARMER F-41160 (12-14) ELECTRICAL REQUIREMENTS warmers ELECTRICAL CODES & STANDARDS: equipped with a three-prong plug. It The warmer must be installed in is imperative that this plug must be accordance with: connected into a properly grounded three-prong receptacle. -
Page 7: Operation Instructions
500-CW, 700-CW, 500-CW-EX, 700-CW-EX CHIP WARMER F-41160 (12-14) OPERATION OPERATION INSTRUCTIONS (Models 500-CW & 700-CW) circulates heated air through the The Warmer and its perforated removable chip tray parts are hot. Be very careful when located at the bottom of the operating, cleaning, or servicing the interior of the cabinet. -
Page 8: Operation Instructions
500-CW, 700-CW, 500-CW-EX, 700-CW-EX CHIP WARMER F-41160 (12-14) OPERATION INSTRUCTIONS (Models 500-CW-EX & 700-CW-EX) The Chip Warmer should be thoroughly Adjust knob desired cleaned before initial use. temperature setting. Once a desired temperature setting is determined, the knob can be left in this position until a The Warmer and its temperature adjustment is needed. -
Page 9: Cleaning Instructions
500-CW, 700-CW, 500-CW-EX, 700-CW-EX CHIP WARMER F-41160 (12-14) CLEANING INSTRUCTIONS (Models 500-CW-EX & 700-CW-EX) The Warmer and its 4. Remove interior baffle at the parts are hot. Be very careful when bottom of the unit. A handle is operating, cleaning, or servicing the located toward the back of the warmer. -
Page 10: Stainless Steel Care
500-CW, 700-CW, 500-CW-EX, 700-CW-EX CHIP WARMER F-41160 (12-14) EXTERIOR CLEANING: STAINLESS STEEL CARE Special stainless steel polishing cleaners can preserve and restore the CLEANING: protective film on the exterior of the unit. Stainless Steel contains 70 – 80% iron, which will rust if not properly maintained. -
Page 11: Lockout / Tagout Procedure
500-CW, 700-CW, 500-CW-EX, 700-CW-EX CHIP WARMER F-41160 (12-14) LOCKOUT / TAGOUT PROCEDURE Always perform the LOCKOUT / TAGOUT PROCEDURE of your facility before removing any sheet metal panels or attempting to service this equipment. The Lockout / Tagout Procedure is used to protect personnel working on an electrical appliance. -
Page 12: Troubleshooting
Damaged fan, etc. Provider SERVICE & PARTS INFORMATION To obtain Service and Parts information concerning this model, contact Wittco Service Department at the address listed on the front cover of this manual or refer to our website: www.wittco.com for a complete listing of Authorized Service and Parts depots. - Page 13 500-CW, 700-CW, 500-CW-EX, 700-CW-EX CHIP WARMER F-41160 (12-14)
Need help?
Do you have a question about the 500-CW-EX and is the answer not in the manual?
Questions and answers