Related Manuals for EMS SmartCell SmartDoor
Summary of Contents for EMS SmartCell SmartDoor
- Page 1 SmartDoor Installation Guide ©2021 EMS Ltd. All rights reserved. MK347-0001-99 Issue 2 25/08/2021 AJM...
-
Page 2: Table Of Contents
Drill floor plate fixing positions Fix floor plate to floor Open fire door & depress plunger Test device Troubleshooting Device tone & flash indication Specification Regulatory information ©2021 EMS Ltd. All rights reserved. Page 2 of 16 MK347-0001-99 Issue 2 25/08/2021 AJM... -
Page 3: Part Number And Description
To ensure correct operation, products must be used within the specified environmental operating conditions. Components SmartDoor Small & large Fixing template Fixings ESD protection floor plates (MK350) label ©2021 EMS Ltd. All rights reserved. Page 3 of 16 MK347-0001-99 Issue 2 25/08/2021 AJM... -
Page 4: Equipment Familiarisation
15 seconds and concludes with three low pitched beeps. Should the sequence close with a mix of high and low pitched beeps, refer to page 13. ©2021 EMS Ltd. All rights reserved. Page 4 of 16 MK347-0001-99 Issue 2 25/08/2021 AJM... -
Page 5: Configuration
SmartCell WZM = MK067 Note: the device can also be programmed utilising the control panel’s cause and effects, as part of the buildings evacuation plan. ©2021 EMS Ltd. All rights reserved. Page 5 of 16 MK347-0001-99 Issue 2 25/08/2021 AJM... -
Page 6: Position Template Against Door
Simply a x the label inside the xing template’s cut out, on to the metal surface. Drill fixing positions Drill all four fixing positions. = 2.5mm ©2021 EMS Ltd. All rights reserved. Page 6 of 16 MK347-0001-99 Issue 2 25/08/2021 AJM... -
Page 7: Fix Unit To Door
Fix unit to door Use all four fixing positions. Use supplied fixing screws. Position floor plate Door Bump stop Ferrule Floor plate Side view ©2021 EMS Ltd. All rights reserved. Page 7 of 16 MK347-0001-99 Issue 2 25/08/2021 AJM... -
Page 8: Mark Floor Plate Fixing Positions
Use small oor plate, if bump stop creates a trip hazard Drill floor plate fixing positions Before drilling, check locations of water pipes, gas pipes & electrical cables = 6 mm ©2021 EMS Ltd. All rights reserved. Page 8 of 16 MK347-0001-99 Issue 2 25/08/2021 AJM... -
Page 9: Fix Floor Plate To Floor
Open fire door & depress plunger Open the door against the bump stop and depress the plunger - check that the ferrule ts neatly into the recess ©2021 EMS Ltd. All rights reserved. Page 9 of 16 MK347-0001-99 Issue 2 25/08/2021 AJM... -
Page 10: Test Device
Test device ©2021 EMS Ltd. All rights reserved. Page 10 of 16 MK347-0001-99 Issue 2 25/08/2021 AJM... -
Page 11: Troubleshooting
Battery fault / device is not powered? Check the polarity and the voltage of the batteries. Check that the battery cover is fitted correctly. ©2021 EMS Ltd. All rights reserved. Page 11 of 16 MK347-0001-99 Issue 2 25/08/2021 AJM... -
Page 12: Device Tone & Flash Indication
† Door closing can be as a result of many factors such as a fire condition, a loss of communication or a battery critical condition. Refer to the control panel for details. ©2021 EMS Ltd. All rights reserved. Page 12 of 16... -
Page 13: Specification
Max. test door friction 0.8 Nm Min. angle between door open 66 ° and closed positions Note: SmartDoor is not for use on metal doors. ©2021 EMS Ltd. All rights reserved. Page 13 of 16 MK347-0001-99 Issue 2 25/08/2021 AJM... -
Page 14: Regulatory Information
March 2012. Fire detection and fire alarm systems. Part 25: Components using radio links. European Union directives EMS declares that the radio equipment type SmartDoor is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.mysmartcell.com... - Page 15 ©2021 EMS Ltd. All rights reserved. Page 15 of 16 MK347-0001-99 Issue 2 25/08/2021 AJM...
- Page 16 ©2021 EMS Ltd. All rights reserved. Page 16 of 16 MK347-0001-99 Issue 2 25/08/2021 AJM...
Need help?
Do you have a question about the SmartCell SmartDoor and is the answer not in the manual?
Questions and answers