Download Print this page

Advertisement

Quick Links

NOTICE TO INSTALLER: Instructions must remain with installation.
Product information presented
of publication. Consult factory
regarding discrepancies or
inconsistencies.
Patent No. 7,203,976
Other Patents Pending
1. Inspect all materials. Occasionally, products are damaged during shipment. If the unit is damaged, contact your dealer before using. Do Not remove the test
plugs from the pump.
2. Carefully read all the literature provided to familiarize yourself with
materials should be retained for future reference.
SEE BELOW FOR LIST OF WARNINGS
1. Make sure there is a properly grounded receptacle available. All pumps
are furnished with provisions for proper grounding to protect you against the
possibility of electrical shock.
2. Make certain that the receptacle is within the reach of the pump's power
supply cord. DO NOT USE AN EXTENSION CORD. Extension cords that
are too long or too light do not deliver
and they could present a safety hazard if the insulation were to become
damaged or the connection end were to fall into a wet or damp area.
3. Make sure the pump electrical supply circuit is equipped with fuses or
circuit breakers of proper capacity. A separate branch circuit is recom-
mended, sized according to governing electrical code for the current shown
on the pump nameplate.
4. Testing for ground. As a safety measure, each electrical outlet should be
checked for ground using a circuit analyzer which will indicate if the power,
neutral and ground wires are correctly connected to your outlet. If they are
not, call a
licensed electrician.
5. For Added Safety. Use of a residual current device with an operating current
not higher than 30 mA is recommended.
6. FOR YOUR PROTECTION, ALWAYS DISCONNECT PUMP FROM
ITS POWER SOURCE BEFORE HANDLING. DO NOT, UNDER ANY
CIRCUMSTANCES, REMOVE THE GROUND PIN. The 3-prong plug must
be inserted into a mating 3-prong grounded receptacle. If the installation
does not have such a receptacle, it must be changed to the proper type,
wired and grounded in accordance with the governing electrical code and
all applicable local codes and ordinances.
7. Risk of electrical shock. Do not remove power supply cord and strain relief
or connect conduit directly to the pump.
8. Installation and servicing of pump, electrical circuits, and hardware should
be performed by a qualified licensed electrician.
9.
Risk of electrical shock.
in swimming pool and marine areas.
10. If the supply cable is damaged, it must be replaced by the manufacturer or
its technical service or similarly
1
. 1
T
e h
appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction conc-
erning use of the appliance by a person responsible for their safety.
1
. 2
u P
m
p
is not intended for potable water due to possible contamination by oil
contained in the pump.
QWIK JON
INSTALLATION INSTRUCTIONS
PREINSTALLATION CHECKLIST
voltage to the pump motor,
These pumps have not been investigated for use
persons in order to avoid a hazard.
© Copyright 2018 Zoeller Co. All rights reserved.
ULTIMA QJU-3 SYSTEM
®
details regarding installation and use before attempting the installation. These
TO AVOID SERIOUS OR FATAL PERSONAL INJURY OR MAJOR
PROPERTY DAMAGE, READ AND FOLLOW ALL SAFETY
INSTRUCTIONS IN THIS MANUAL AND ON THE PUMP.
THIS MANUAL IS INTENDED TO ASSIST IN THE INSTALLATION AND
OPERATION OF THIS UNIT AND MUST BE KEPT WITH THE PUMP.
CAUTION
THOROUGHLY REVIEW ALL INSTRUCTIONS AND WARNINGS PRIOR
TO PERFORMING ANY WORK ON THIS PUMP.
MAINTAIN ALL SAFETY DECALS.
- 1 -
50 Hz
Visit our web site:
www.zoellerpumps.com
M
O
D
L E
N
DATE CODE: __________________
DATE INSTALLED: _____________
SAFETY INSTRUCTIONS
SAFETY ALERT SYMBOL.
This is a
When you see this symbol on the pump or in the manual
look for one of the following signal words and be alert to
the potential for personal injury or property damage.
Warns of hazards that CAN cause serious personal injury,
death or major property damage.
Warns of hazards that CAN cause personal injury or
property damage.
Warns of electrical shock hazards that CAN cause serious
personal injury, death or major property damage.
Identifies any terminal which is intended for connection
to an external conductor for protection against electrical
shock in case of a fault, or the terminal of a protective
earth (ground) electrode.
Read operator's manual.
REFER TO WARRANTY ON PAGE 2.
ZT0178_ECb
0818
Supersedes
0718
. O
_ _
_ _
_ _
_ _
_ _
_ _
_ _
_ _
_ _
_ _
P/N 082802

Advertisement

loading
Need help?

Need help?

Do you have a question about the QWIK JON ULTIMA QJU-3 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Zoeller QWIK JON ULTIMA QJU-3

  • Page 1 P/N 082802 © Copyright 2018 Zoeller Co. All rights reserved. - 1 -...
  • Page 2: Limited Warranty

    2. DO inspect unit for any visible damage caused by shipping. Contact dealer if unit appears to be damaged. 9. DO inspect and test system for proper operations at least every 3 months. © Copyright 2018 Zoeller Co. All rights reserved. - 2 -...
  • Page 3: Service Parts

    Discharge fittings Carbon filter vent Tank Nut with straight pipe adapter Check valve Seal Rubber coupling with hose clamps Extension kit for behind the wall install (optional) Piggyback switch © Copyright 2018 Zoeller Co. All rights reserved. - 3 -...
  • Page 4 (See Note 2) 150630 Cutter 150211 ------ Loctite - Cutter Retaining Screw LOCTITE #222 - PINK Screw 001884 Retainer 150635 Screw 017341 Screw 018568 Guard,Cutter Plastic 150415 Pump Housing 018569 © Copyright 2018 Zoeller Co. All rights reserved. - 4 -...
  • Page 5 If the above checklist does not solve the problem, consult local agent e-mail to sales@zoeller.com.tw. Do not attempt to service or otherwise disassemble pump. © Copyright 2018 Zoeller Co. All rights reserved. - 5 -...
  • Page 6: Location Selection

    Ensure that nails, screws or other sharp objects do not puncture the pump unit! Level the pump unit to within 3 mm (1/8") using hydraulic cement or similar material. EA0062 © Copyright 2018 Zoeller Co. All rights reserved. - 6 -...
  • Page 7 See sketch at right. Set toilet aside. Toilet assembly is top heavy. Take special precautions to ensure that toilet does not tip over and break. EA0063 © Copyright 2018 Zoeller Co. All rights reserved. - 7 -...
  • Page 8 If leakage occurs, please replace the o-ring. Available for connecting outside Indentation diameter Ø32 mm or 1" pipe. Only need to reverse the pipe adaptor. Check valve Check valve EA0064 © Copyright 2018 Zoeller Co. All rights reserved. - 8 -...
  • Page 9 STEP 7 Replace the carbon filter Carbon filter vent To maintain effective ventilation, please replace the carbon filter periodically. (1) Open the cover. (2) Replace the carbon filter. EA0056 © Copyright 2018 Zoeller Co. All rights reserved. - 9 -...
  • Page 10: Pump Performance

    TOTAL DYNAMIC HEAD/FLOW SEWAGE MODEL QJU-3 Meters Feet m /hr 13.1 16.4 Shut-off Head: 6.5 m (21.3 ft) 082807 m /hr FLOW RATE These are the original installation instructions. © Copyright 2018 Zoeller Co. All rights reserved. - 10 -...
  • Page 11 或斷路器。在此建議依照水泵銘牌上的電流值,並參照 亡或重大財產損失的危險。 國內電工法則來選擇及安裝獨立的斷路器。 請在安裝前測試插座的漏電保護功能。為了安全考量, 注意,表示可能會造成人身傷害或財產損失 CAUTION 請使用符合國內電工法規的電路測試儀器來檢查插座中 的危險。 的火線、中性線及地線是否配置正確。若發現異常,請 電擊危險警告,表示可能會導致嚴重的人身 聯絡合格的水電技師來為您解決問題。 傷害、死亡或重大財產損失的危險。 為增加安全性使用漏電保護裝置,建議漏電流不超過30 mA。 接地標誌,表示藉由連接外部導體之接地線, 僅得由持有證照的合格水電技師來進行水泵安裝、管路 在故障時可防止觸電發生。 搭配及電路配線。 為避免觸電,請勿移除電纜線。 閱讀操作手冊。 為了保護您的安全,接觸水泵前請先拔除電源。 使用水泵前,請徹底閱讀本說明書內的說明和警告。 為防範觸電,本產品勿用于游泳池。 並維護所有安全標籤。 如果電纜線受損,請聯絡經銷商或本公司認可的服務單 位維修。 若無監督本產品不適合給兒童、心智不健全或經驗不足 者使用,前述條件者使用本產品時,監督者應負全部安 全責任。 保修請參閱第12頁。 水泵不可使用於飲用水,冷卻油有可能會污染水質。 © 版權所有 : 2018 Zoeller 公司。翻印必究。 - 11 -...
  • Page 12 3. 安裝排水管密封件時,法蘭密封面向外面。 3. 請務必清理裝置所有可見的雜物。 4. 必要時請使用肥皂水潤滑配件,以協助安裝。 4. 處理前切斷泵浦電源。連結到獨立受保護的接地漏電 5. 在通氣口上安裝碳製通氣閥,需定期更換活性碳濾棉。 電流斷路器。請勿切斷、拼接或損壞電源線。請勿用 6. 請不要過度鎖緊馬桶安裝的固定螺絲。 電源線拉動或舉起水泵。請勿使用延長線。 5. 請務必在逆止閥的排水管下游安裝球閥或閘閥。 7. 請避免使用自動管道通氣設備。 6. 請務必在安裝後立即測試水泵,以確認系統正常運作。 8. 請記錄本機型號及製造日期,與經銷商聯絡時提供 7. 請務必詳閱所有適用當地及國家規則,確認安裝符合 本資訊。 各項規定。 8. 不建議將本產品連結到正常浴室設施以外的設施,如 洗衣機及洗碗機。 9. 務必每三個月檢查並測試系統的正常運作。 © 版權所有 : 2018 Zoeller 公司。翻印必究。 - 12 -...
  • Page 13 托架型鋼 PVC彎管** 至少 203 mm EA0067 *天花板高度僅供參考。 **選項:帶金屬扣環的軟管。 維修零件 項目 描 述 ® Qwik Jon Ultima 提升器 磨碎型水泵 (附出水管) 提升器上蓋 出水口組件 碳製通氣閥 提升器 螺母與直管接頭 止回閥 密封件 波紋管橡膠接頭與鐵箍 牆後安裝用延伸套件 (選配) 外接式浮子開關 EA0068 © 版權所有 : 2018 Zoeller 公司。翻印必究。 - 13 -...
  • Page 14 每台狀況 華斯 (切盤與切刀中間) 017319 而定 017320 (見備註2) 150630 150211 切刀 ------ (Loctite) LOCTITE #222 - PINK 切刀固定螺絲須塗樂泰膠 001884 切刀固定螺絲 (固定切刀在軸心上) 150635 螺帽 (固定切刀) 017341 螺絲 018568 螺絲 150415 切刀護盤 018569 水機 © 版權所有 : 2018 Zoeller 公司。翻印必究。 - 14 -...
  • Page 15 聯絡經銷商。 水泵氣鎖。 確保排放管中的通氣孔暢通。 安裝揚程超過系統設計的揚程。 更換排放管或聯絡經銷商。 警 告 注 意 在維修沉水泵之前,須關閉總電源斷路器,拔除水泵 不要將女性生理用品、可拋棄式尿片、抹布等丟入 QWIK JON ULTIMA 中。這可能堵塞水泵或其他管道, ® 插頭——確保人未站在水中,且穿上絕緣保護底的鞋子。 水溢流時,聯絡當地的電力公司,或有執照的合格電氣 導致故障。 技師,在移除管之前進行斷電。 完成后的保養:僅建議使用肥皂和水清洗水箱外側。其他 清潔產品可能造成褪色和刮傷。 警 告 本水泵含冷卻油,在運作狀態下會 受壓變熱—— 斷電后等待2.5 小時再進行維修。 ——如果以上檢查點都無法排除問題, 請與經銷商聯絡, 不要嘗試維修或拆除沉水泵及其他零件。 © 版權所有 : 2018 Zoeller 公司。翻印必究。 - 15 -...
  • Page 16 下水道:需要連結到糞管排放。 Qwik Jon Ultima ® 要求有外徑Ø32 mm或1 英吋(若當地規則許可,也可為外 徑Ø25 mm或3/4 英吋的管路),以連結 到既有的糞管。 供水裝置 排放管路上應安裝球閥或閘閥。 碳製通氣閥:需定期更換活性碳濾棉。不建議採用機械式 平地 通氣系統。 備註:若欲採用隱藏安裝,請將提昇器設在維修人員 SK2588 有足夠空間維修拆裝的地方。 水泵裝置 步驟 注 意 勿使用木質墊片校平提昇器。 注 意 確保釘子、螺絲或其他尖銳物不會刺穿提昇器。 使用水硬水泥或類似材料將水泵校平至差距在 3 mm之內。 EA0062 © 版權所有 : 2018 Zoeller 公司。翻印必究。 - 16 -...
  • Page 17 進行最後安裝。馬桶水箱應離牆至少13 mm。 3) 在地板上輕輕標記水泵裝置、馬桶和馬桶螺絲的位置。 在牆上輕輕標記水泵裝置及馬桶水箱底部和側邊的高 度,以確保未來實際安裝馬桶水箱和管路時,不會發 生干涉。 4) 將馬桶卸離水泵,另外安放。 EA0063 步驟 簡圖(隱藏式安裝) 1) 安裝牆后水泵組須有另外販賣的延伸 套件(P/N10-3050)。 2) 將馬桶組件安置在離牆至少13 mm處, 並在地板上標記馬桶螺絲的位置。 3) 測量延伸套件中的PVC規格Schedule 40管徑3-1/2 英吋的水管所需長度再加 以裁切安裝。參見右圖。 4) 將馬桶另外安放。 注 意 馬桶組件頭重腳輕,要特別注意,確保馬 桶不會傾倒破碎。 EA0063 © 版權所有 : 2018 Zoeller 公司。翻印必究。 - 17 -...
  • Page 18 Qwik Jon Ultima ® 的設計可 備註:增加其他浴室配備—— 注 意 以利用兩側邊的進水口,接受額外的浴室配備。可直接接 馬桶沖水需要適當的通氣。不要使用機械式通氣系統。 外徑Ø32 mm 或1 英寸直管,簡單的扭轉轉接頭並且切出 3) 暫時將馬桶安放在位置上,檢查是否有管道干涉情況。 模內插件所提供的刻痕。 卸下馬桶放在一旁。 注 意 4) 清洗、裝填、溶劑熔接排放管道和水泵裝置排放配件。 完整的切除並且移除毛邊及粗糙的邊緣來防止阻塞。 塑膠螺母不可使用工具鎖緊,若發生漏水請更換O型環。 刻痕 可直接接外徑Ø32 mm或1 英寸直管, 只需將直管接頭反轉即可。 止回閥 止回閥 EA0064 © 版權所有 : 2018 Zoeller 公司。翻印必究。 - 18 -...
  • Page 19 桶排放管,以提供的蝸輪式夾件固定到延伸管。參見步驟 5 簡圖。 供水管 4) 將供水管從既有的斷流閥安裝到供水聯結。 碳製通氣閥 5) 打開供水閥,檢查是否有漏水。馬桶水箱應注到適當水位。 (需定期更換 活性碳濾棉) 必要時進行調整。 6) 將水泵電源線插到外接浮球開關插座,然後將外接浮球開 關插到接地電路斷路器插座。 輔助進水口 7) 沖馬桶,觀察是否正常運作。聆聽水泵開始啟動。水泵需 水泵裝置 要適當的通氣,馬桶才能沖水。檢查是否漏水。 地板水平誤差需在 3 mm 之內 EA0065 更換活性碳濾棉 步驟 請定期更換活性碳濾棉,以達到適當的通氣。 (1)打開上蓋 (2)更換活性碳濾棉 EA0056 © 版權所有 : 2018 Zoeller 公司。翻印必究。 - 19 -...
  • Page 20 米 呎 水泵性能曲線 QJU-3系列 - 50 Hz 總 總動力揚程/流量 動 QJU-3 型號 力 Meters Feet m /hr 揚 程 13.1 16.4 6.5 米 (21.3 英尺) 全閉揚程 082807 m /hr 流量 這是原始安裝說明的翻譯。 © 版權所有 : 2018 Zoeller 公司。翻印必究。 - 20 -...