Sealey SA912.V3 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
‰
WARNING! Disconnect from air supply before changing accessories or servicing.
‰
Maintain the wrench in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
‰
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
9
Only use impact sockets which are specifically designed for use with an impact wrench.
9
Wear approved safety eye/face shield, ear defenders and hand protection.
9
WARNING! Due to the possible presence of asbestos dust from brake linings, when working around vehicle brake systems we
‰
recommend you wear suitable respiratory protection.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and non-essential persons away from the working area.
9
DO NOT use the wrench for a task it is not designed to perform.
8
WARNING! DO NOT use wrench if damaged or thought to be faulty (contact Service Agent).
‰
DO NOT use wrench unless you have been instructed in its use by a qualified person.
8
DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
8
DO NOT operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT carry wrench with your hand on the trigger in order to avoid unintentional starting.
8
DO NOT direct air from the air hose at yourself or others.
8
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
2. INTRODUCTION
Pistol type wrench with rocking-dog hammer and hardened anvil assembly. Fitted with four-position air/torque control and push-through
reverse control. Compact and lightweight tool suitable for engine bay work.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . .SA912.V3
Drive: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/8"
Breakaway Torque:. . . . . . . . . . . . . . . . 200lb.ft(271Nm)
Maximum Torque: . . . . . . . . . . . . . . . . . 190lb.ft(258Nm)
Free Speed: . . . . . . . . . . . . . . . . . . . . . . . . . 10,000rpm
Air consumption:. . . . . . . . . . . . . . . . . . . . . . . . . 3.5cfm
Operating Pressure: . . . . . . . . . . . . . . . . . . . . . . . .90psi
Air Inlet: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4"BSP
Noise Power: . . . . . . . . . . . . . . . . . . . . . . . . 101.8dB(A)
Noise Pressure: . . . . . . . . . . . . . . . . . . . . . . . 90.3dB(A)
Vibration: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.17m/s²
Uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5m/s²
Nett Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.97kg
© Jack Sealey Limited
AIR IMPACT WRENCH 3/8"SQ DRIVE
HEAVY-DUTY
MODEL NO:
Wear protective Wear ear
gloves protection
Original Language Version
SA912.V3
Wear a mask
SA912.V3 | Issue 1 09/11/18