Sealey SA6009 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
1.1. GENERAL SAFETY
WARNING! Disconnect from air supply before changing accessories or servicing.
‰
Maintain the wrench in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
Tools shall be inspected periodically to verify that the markings are legibly marked on the tool. The user shall contact the manufacturer to
9
obtain replacement marking labels when necessary.
WARNING! Check correct air pressure is maintained and not exceeded the maximum operating pressure of 90psi.
‰
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
9
Wear approved safety eye/face shield, ear defenders and hand protection.
9
DO NOT use the wrench for a task it is not designed to perform.
8
DO NOT modify this assembly power tool. Modifications can reduce the effectiveness of safety measures and increase the risks to the
8
operator.
DO NOT discard the safety instructions; give them to the operator.
8
DO NOT use the power tool if it has been damaged.
8
WARNING! DO NOT use wrench if damaged or thought to be faulty (contact Service Agent).
‰
WARNING! Only qualified and trained operators should install, adjust or use the assembly power tool.
‰
DO NOT operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT carry wrench with your hand on the trigger in order to avoid unintentional starting.
8
WARNING! High sound levels can cause permanent hearing loss. Use hearing protection.
‰
1.2. HAZARDS
WARNING! For multiple hazards, read and understand the safety instructions before installing, operating, repairing, maintaining,
‰
changing accessories on, or working near the assembly power tool for threaded fasteners. Failure to do so can result in serious bodily
injury.
WARNING! This tool and its accessories must not be modified.
‰
WARNING! Proceed with care in unfamiliar surroundings. Be aware of potential hazards created by your work activity.
‰
Keep children and non-essential persons away from the working area.
9
WARNING! Due to the possible presence of asbestos dust from brake linings, when working around vehicle brake systems we
‰
recommend you wear suitable respiratory protection.
1.3. PROJECTILE
WARNING! Serious injury can result from over-torqued or under-torqued fasteners, which can break, or loosen and separate. Released
‰
assemblies can become projectiles. Assemblies requiring a specific torque must be checked using a torque meter.
WARNING! Failure of the wokpiece, of accessories or even of the inserted tool itself can generate high-velocity projectiles.
‰
WARNING! Always wear impact-resistant eye protection during the operation of the assembly power tool for threaded fasteners. The
‰
grade of protection required should be assessed for each use.
WARNING! Ensure that the workpiece is securely fixed.
‰
1.4. ENTANGLEMENT
WARNING! Entanglement hazards can result in choking, scalping and/or lacerations if loose clothing, personal jewellery, neckwear, hair or
‰
gloves are not kept away from the tool and accessories.
DO NOT wear loose-fitting gloves or gloves with cut or frayed fingers.
8
WARNING! Never hold the drive, socket or drive extension.
‰
WARNING! Keep hands away from rotating drives.
‰
WARNING! Gloves can become entangled with the rotating drive, causing severed or broken fingers.
‰
WARNING! Rotating drive sockets and drive extensions can easily entangle rubber-coated or metal-reinforced gloves.
‰
1.5. OPERATING
WARNING! The use of the tool can expose the operator's hands to hazards including crushing, impacts, cuts and abrasions and heat.
‰
Wear suitable gloves to protect hands.
Operators and maintenance personnel must be physically able to handle the bulk, weight and power of the tool.
9
WARNING! Hold the tool correctly; be ready to counteract normal or sudden movements and have both hands available.
‰
WARNING! DO NOT use in confined spaces and beware of crushing hands between tool and workpiece, especially when unscrewing.
‰
Release the start-and-stop device in the case of an interruption of the energy supply.
9
It is not recommended to use the product in excessively humid environments. Recommended temperature range: -20°C to +50°C.
9
© Jack Sealey Limited
1"SQ 6" EXTENDED ANVIL IMPACT WRENCH
MODEL NO:
Wear protective Wear ear
gloves protection
Original Language Version
SA6009
Wear a mask
SA6009 Issue 1 17/12/24