Issue No:
1
Date Issued:
151104
Item
Part No
Description
1
GSA02.01
HOUSING
2
GSA01.02
O-RING
3
GSA01.03
CAP SCREW
4
GSA02.04
HAMMER CASE
5
GSA01.05
SPRING PIN
6
GSA01.06
TRIGGER
7
GSA01.08
VALVE SEAT
8
GSA01.09
THROTTLE VALVE
9
GSA01.10
VALVE SPRING
10
GSA01.11
EXHAUST DEFLECTOR
11
GSA02.11
TRIGGER BUSHING
12
GSA01.12
AIR INLET
13
GSA02.13
PLASTIC GRIP
14
GSA01.14
VALVE BUSHING
15
GSA01.15
WASHER
16
GSA01.16
SWITCH
17
GSA01.17
PIN
18
GSA01.18
REVERSE KNOB
19
GSA20.07
SPRING
20
GSA20.08
LOCK PIN
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and
promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
Parts List For:
GSA02
Item
Part No
Description
21
GSA02.21
FRONT END PLATE
22
GSA01.22
ROTOR
23
GSA01.23
ROTOR BLADE
24
GSA01.24
FRONT DOWEL PIN
25
GSA01.25
CYLINDER
26
GSA01.26
REAR DOWEL PIN
27
GSA02.27
REAR END PLATE
28
GSA02.28
FRONT BEARING
29
GSA01.29
REAR COVER GASKET
30
GSA01.30
REAR COVER
31
GSA01.31
OIL SEAL
32
GSA01.42
TRIGGER SHAFT
33
GSA02.33
HAMMER PIN
34
GSA02.34
HAMMER
35
GSA02.35
HAMMER CAGE
36
GSA02.36
STANDARD ANVIL
37
GSA01.37
O-RING
38
GSA01.38
ANVIL COLLAR
39
GSA02.39
ANVIL BUSHING
40
GSA01.41
REAR COVER COLLAR
41
GSA02.41
O-RING
01284 757500
Web address: www.sealey.co.uk
01284 703534
E-mail: sales@sealey.co.uk
GSA02 - 1 - 151104
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
3 Follow all workshop safety rules, regulations, and conditions when using wrench.
p WARNING! Disconnect from air supply before changing accessories or servicing.
3 Maintain the wrench in good condition and replace any damaged or worn parts. Use
genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
p WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
3 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each
use and ensure that all connections are secure.
3 Only use impact sockets which are specifically designed for use with an impact wrench.
3 Wear approved safety eye/face shield, ear defenders and hand protection.
p WARNING! Due to the possible presence of asbestos dust from brake linings, when working
around vehicle brake systems we recommend you wear suitable respiratory protection.
3 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3 Keep children and non essential persons away from the working area.
7 DO NOT use the wrench for a task it is not designed to perform.
WARNING! DO NOT use wrench if damaged or thought to be faulty. (Contact Service Agent).
p
p
7 DO NOT use wrench unless you have been instructed in its use by a qualified person.
7 DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
7 DO NOT operate wrench if you are tired, under the influence of alcohol, drugs or intoxicating medication.
7 DO NOT carry wrench with your hand on the power trigger in order to avoid unintentional starting.
7 DO NOT direct air from the air hose at yourself or others.
3 When not in use disconnect from air supply and store in a safe, dry, childproof location.
2.
INTRODUCTION & SPECIFICATION
Third Generation twin hammer impact wrench.
Suitable for garage, tyre shop and workshop
applications. Handle exhaust reduces noise output
and contoured soft-grip handle gives added
comfort and control. Features three-position
adjustable air/torque control and reversible action.
Drive size . . . . . . . . . . . . . . . . . . . . . . . . . .1/2
Working/Max torque . . . . . . . . . . . .400/460ft.lb
Ultimate torque . . . . . . . . . . . . . . . . . . . 500ft.lb
Air consumption . . . . . . . . . . . . . . . . . . .5.6cfm
Operating pressure . . . . . . . . . . . . . . . . .90psi
Air inlet size . . . . . . . . . . . . . . . . . . . . .1/4BSP
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.1kg
Noise . . . . . . . . . . . . . . . . . . . . . . . . . . .94.2dB
Vibration . . . . . . . . . . . . . . . . . . . . . . . .4.4m/s
INSTRUCTIONS FOR:
1/2SQ DR G3 AIR
IMPACT WRENCH
MODEL: GSA02
2
GSA02 - 1 - 151104