Table of Contents
Advertisement
Quick Links
Photographs are not to scale.
Specifications subject to change
without prior notice.
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open barbecue lid or hood.
4. If odour continues, discontinue use and contact
your local dealer.
Assembly and Operating Instructions for
®
Outback
Signature Stainless Steel Flame Tower
OUT370665
PH300
1. Do not store or use petrol or other flammable
vapours or liquids in the vicinity of this or any
other appliance.
2. A gas bottle not connected for use must not be
stored in the vicinity of this or any other
appliance.
0063
FOR YOUR SAFETY
0558
Advertisement
Table of Contents
Related Manuals for Outback OUT370665
Summary of Contents for Outback OUT370665
- Page 1 Assembly and Operating Instructions for ® Outback Signature Stainless Steel Flame Tower OUT370665 PH300 Photographs are not to scale. Specifications subject to change 0558 0063 without prior notice. FOR YOUR SAFETY FOR YOUR SAFETY If you smell gas: 1. Do not store or use petrol or other flammable 1.
- Page 2 WARNlNG SAFETY RULES PLEASE READ THE FOLLOWING SAFETY RULES PRlOR TO OPERATION OF THE HEATER. This appliance must be installed and the gas cylinder stored in accordance with the regulations in force; Do not obstruct the ventilation holes of the cylinder housing; Do not move the appliance when in operation;...
-
Page 3: Assembly Parts
ASSEMBLY PARTS Quantity varies according to model purchased. Specifications subject to change without prior notice. Tools needed: Philips screwdriver w/ medium blade Spray bottle of soap solution for leakage test Parts List: Reflector Flame Screen Glass Tube Upper Support Protective Guard Black Silicone Ring Control Box Assy Side Panel... - Page 4 ASSEMBLY PARTS HARDWARE CONTENTS (shown actual size) Wing nut Stud Flange Small flat Qty. 3 Qty. 3 Qty. 42 Qty. 4 Qty. 4 Qty. Philips Knob Qty. 1 Qty. 1 Qty. 1 Qty.1 Qty. 4 Qty. Chain Long Stem Lighter AA Battery (1.5 V) Qty.1 Qty.1...
- Page 5 PARTS Quantity varies according to model purchased. Specifications subject to change without prior notice. 650 mm Reflector Flame Screen Glass Tube Protective Guard Upper Support Front Panel Side Panel Lower Support Bottom plate 730 mm...
- Page 6 ASSEMBLY IMPORTANT! Whilst every care is taken in the manufacture of this product, care must be taken during assembly in case sharp edges are present. Please read the Important Information section carefully before assembly. 1. Assemble the wheel assembly to the bottom plate. Fix the wheel assembly to the bottom plate using 4pcs bolt M6X12 and 4pcs lange nut Hardware Used...
- Page 7 3. Assemble block belt. Fix the block belt to the 2pcs of lower support behind the front door, using 2pcs screw M5X12. Hardware Used Philips Screw M5 X 12 screwdriver 4. Assemble the middle support.Insert the 4pcs upper support to the lower support. Secure them with 8pcs screw 3/16”.
- Page 8 5. Assebmle the flame screen to the upper support.Secure the flame screen to the upper support using 8pcs screw “3/16”. Hardware Used Philips 3/16” Screw screwdriver 6. Assemble the reflector onto the flame screen. Screw the 3pcs stud on the flame screen, put 3pcs washer 6 onto the top of stud,then put the reflector onto the stud, secure them with 3pcs washer...
- Page 9 To aid in installation place black silicone ring on the middle plate and then install glass tube. Ensure the rim of the glass tube sits firmly in the black silicone ring. BLACK SILICONE RING 7. Carefully install the glass tube by lifting up and inserting through the center hole in the upper plate.
- Page 10 9. Attach the three side panels to the heater using 18pcs screw 3/16”. Note : Do not cover the front side where the control knob is. Hardware Used Philips 3/16” Screw x 18 screwdriver 10. Install the knob to M4x10 screw. Hang the chain to the hole on the control box assy and put the pothook of front panel to the holes of bottom plate.
- Page 11 11. Propane Only-Proper Hose Connection. WARNING! Ensure the hose does not contact any high temperature surfaces,or it may melt and leak causing a fire. After the cylinder is placed inside the heater, secure the cylinder with block belt tightly. 12. Leak Check. WARNING! of the gas system is replaced.
-
Page 12: Leakage Test
LEAKAGE TEST Gas connections on the heater are leak tested at the factory prior to shipment. A complete gas tightness check must be performed at the installation site due to possible mishandling in shipment or excessive pressure being applied to the heater. - Page 13 CAUTION PLEASE READ CAREFULLY THE FOLLOWING SAFETY GUIDELINES BEFORE OPERATION. Do not use the patio heater for indoors, as it may cause personal injury or property damage. This outdoor heater is not intended to be installed on recreational vehicles and/or boats.
-
Page 14: Heater Stand And Location
Adults and children should stay away from high temperature surface to avoid burns or clothing ignition. Children should be carefully supervised when they are in the area of the heater. Clothing or other flammable materials should not be hung on the heater or placed on or near the heater. -
Page 15: Gas Requirements
GAS REQUIREMENTS Use propane or butane gas only. The pressure regulator and hose assembly to be used must conform to local standard codes. The installation must conform to local codes, or in the absence of local codes, with the standard for the storage and handling of liquid petroleum gases. A dented, rusted or damaged propane tank may be hazardous and should be checked by your tank supplier. - Page 16 TO TURN OFF THE HEATER 1. Turn the variable control knob to PILOT position. 2. Press and turn the variable control knob to OFF position. OFF: the heater stop work HI: maximum temperature position LO: minimum temperature position lgniter Igniter Variable control knob 3.
-
Page 17: Characteristics And Specifications
CHARACTERISTICS AND SPECIFICATIONS A. Construction and characteristics Transportable terrace/garden heater with tank housing Casing in steel with powder-coating or stainless steel Gas hose connections with metal clamp (screw caps for Germany) Heat emission from reflector B. Technical Specifications Use propane, butane or their mixtures gas only. Max. -
Page 18: Problems Check List
Control not ON Turn valve to ON Thermocouple bad Replace thermocouple Pilot light assembly bent Place pilot properly Not in correct location Position properly and retry Outback International (UK) Ltd. Unit 4, Madley Airfield Industrial Estate, Stoney Street, Madley Herefordshire. HR2 9NQ... - Page 19 OUTBACK® WARRANTY OUTBACK® heater are warranted for a period of one (1) year from the date of purchase to the original purchaser against defects in materials and workmanship, OUTBACK® will supply replacements for defective parts free of charge provided that: The product has not been used for trade, professional or hire purposes.