Page 1
NOTE: Please read all instructions carefully before using this product MARCY DIAMOND Table of Contents OLYMPIC BENCH Safety Notice Hardware Identifier MD-823 Assembly Instruction Parts List Warranty Ordering Parts Model MD-823 Retain This Manual for Reference 100915 OWNER'S MANUAL ®...
ORDERING PARTS..................………… 14 BEFORE YOU BEGIN Thank you for selecting the MARCY DIAMOND MD-823 Olympic Bench by IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
Page 4
WARNING LABEL PLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown...
ASSEMBLY INSTRUCTION Tools required for assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Attach the Left Upright Beam (#1) to a Rear Base Frame (#14).
Page 9
STEP 2 (See Diagram 2) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Attach the Leg developer Holder (#5) to the Front Base (#10). Secure it with two M10 x 5/8”Allen Bolts (#56) and two Ø ¾” Washers (#70). Thread a Lock Knob (#51) into the Leg Developer Holder.
Page 10
STEP 3 (See Diagram 3) A.) Place the Backrest Adjustment Bar (#7) onto the selected slots on the Left & Right Upright Beam (#1 & #2). B.) Attach the pivot on Seat Incline Support (#12) into the side holes on the two Seat Supports (#11).
Page 11
STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#8) to the Leg Developer Holder (#5). Secure it with one M10 x 3 1/8” Allen Bolt (#61), two ¾” Washers (#70), and one M10 Aircraft Nut (#68). B.) Insert the Leg Developer Weight Post (#25) into the hole on Leg Developer. Secure it with one M10 x 2 3/8”...
Page 12
STEP 5 (See Diagram 5) A.) Attach the Backrest Board (#31) to the Backrest Supports (#13). Secure it with four M8 x 1 5/8” Allen Bolts (#55) and four Ø 5/8” Washers (#69). B.) Attach the Seat Pad (#30) to the Seat Supports (#11). Secure it with four M8 x 1 5/8” Allen Bolts (#55) and four Ø...
PARTS LIST KEY NO. DESCRIPTION Q’ty Left Upright Beam Lock Knob Right Upright Beam Grip Cross Brace Olympic Sleeve Main Seat Support M8 x 5/8” Allen Bolt Leg Developer Holder M8 x 1 5/8” Allen Bolt Sliding Block M10 x 5/8” Allen Bolt Backrest Adjustment Bar M10 x ¾”...
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the customer. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes.