Page 1
: scale BWRRS1 owner’s manual READ THIS MANUAL PRIOR TO FIRST USE AND SAVE FOR FUTURE REFERENCE 1-year Limited Warranty...
Page 2
Ratio Scale Components TIMER 13 14 TIMER Silicone Pad Ratio / Target 15. Timer Platform Weight Readout 16. Actual Weight LCD Readout 10. ON/OFF Button Readout USB Charging 11. MODE Button 17. Weight Unit Port (On Back) 12. RATIO Button (g or oz) Coffee Bean Icon 13.
General Maintenance and Care • Avoid exposure to extreme heat or cold. – Always allow your scale to acclimate to normal room temperature before use. • Keep your scale in a clean environment. – Excessive dust, dirt, vibration, air currents, as well as close proximity to other electronic equipment may have an adverse effect on the accuracy and reliability of the scale.
Mode Setting • Turn on the scale by pressing the ON/OFF button. • Wait until the LCD displays zero. • Press the MODE button; – The display will read “ A ” (Automatic Mode) or “ M ” (Manual Mode) in the upper left or “ ”...
Charging the Battery • Open the orange USB port cover at the back of the scale and insert the small end of the USB cable in this port. • Plug the USB cable into a USB compatible outlet to charge your scale’s battery.
Operation Please note: • When removing weight from scale, do not apply downward force or slide items off of the platform. Doing so may result in inaccurate readings. Lift items directly off of the platform. • Heat transfered from the brew vessel to the scale will alter weight readings slightly.
Page 8
– Refer to the “Changing Ratio Amount” section later in this manual to select the desired ratio. Auto Mode A : (Automatic Zero and Timer) • Place brewing vessel on the scale platform. – After 3 seconds, weight reading goes to “0.0” (Auto-tares).
Page 9
– When the weight of the added water reaches 60g less than the calculated amount shown at the top right of LCD, the screen begins to flash. This means that you are close to the final amount of water needed. • Once the Target Weight is reached, the display color will change from orange to white. – Timer continues to count up. –...
Page 10
– Scale will calculate the target weight using the selected ratio. – Target weight will be displayed in the upper right of the LCD screen. • When kettle icon appears and weight in lower right of LCD reads, “0.0”: – Start the timer by pressing the TIMER button. ·...
Page 11
• Stop adding water to the brewing vessel. – If the vessel is removed from the scale weight in lower right will show a negative reading. – Timer will continue. Press the TIMER button to stop the timer. – Press the TIMER button again to reset the timer to zero. –...
• When desired weight of the water is reached, stop adding water, and press the TIMER button to turn off timer. – Holding the TIMER button for 3 seconds will return timer to zero. Zero (Tare) Function • Zero function is disabled under “AUTO” mode. •...
– After choosing the desired time, press the ON/OFF button again. – The display will show “PASS” to confirm this setting. – The scale will turn off automatically. Note: – If “60”, “120”, or “180” is chosen, the scale will turn off after the designated number of seconds of inactivity. –...
Page 14
Changing The Set Ratio • Press and hold the RATIO button for 3 seconds. – The ratio will display blinking in the upper right of the LCD. • Press the RATIO button until the desired ratio is displayed. – The default ratio is 1:17 (add 1 part coffee to 17 parts water).
Warning Messages • “ ”: Overload • Quickly remove weight from platform to protect the scale. • “ ”: Unstable – Scale is not steady during start up. Please turn off scale, set on a stable surface and restart scale. ·...
They can collect this product for environmentally safe recycling. Warranty Information • Brewista products that have an ON/OFF switch carry a one-year warranty from the date of original purchase. • This warranty extends only to the original consumer, purchaser, or gift recipient. Keep the original sales receipt, as proof of purchase is required to make a warranty claim.
Need help?
Do you have a question about the BWRRS1 and is the answer not in the manual?
Questions and answers