Technical Data; Before Starting The Machine; Operation - Einhell Royal BHS 26 Original Operating Instructions

Anleitung_BHS_26_SPK1:_
GB

4. Technical data

Engine type:
2-stroke engine, air-cooled, chrome cylinder
Engine output (max.):
Displacement:
Idle speed of engine:
Max. engine speed
Weight (with empty tank):
Cutter rail length:
Cutting length:
Tooth spacing:
Cutting capacity (max.)
Tank capacity:
Spark plug:
Max. cutting speed
Vibration (front handle) a
hv
Vibration (rear handle) a
hv
Sound pressure level L
pA
Sound power level L
WA
Sound and vibration were measured in accordance
with DIN EN 10517.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever
necessary.
Switch the appliance off when it is not in use.
Wear protective gloves.

5. Before starting the machine

5.1 Installation
The hedge trimmer is supplied fully assembled. No
assembly work is required.
To make it easier to control, the machine is fitted with
a rotary handle that can be adjusted as required into
positions at angles of -90°/-45°/0°/+45°/+90°. To do
this, pull the lever (Fig. 5/Item B) backwards, turn the
rotary handle into the required position and then
allow the lever to lock at the front again. The various
14
13.07.2009 9:30 Uhr Seite 14
adjustable positions facilitate working above head
height or in other places with different access.
Please note: The rotary handle may only be
adjusted when the engine is switched off.
5.2 Fuel and oil
0.75 kW / 1.0 hp
Recommended fuels
26 cc
Use only a mixture of normal unleaded petrol and
special 2-stroke engine oil. Mix the fuel mixture as
2960 min -1
indicated on the fuel mixing table.
8800 min -1
5.5 kg
Please note: Do not use a fuel mixture which has
been kept for longer than 90 days.
65 cm
52 cm
Please note: Do not use 2-stroke oil with a
28 mm
recommended mixing ration of 100:1. If inadequate
lubrication causes engine damage, the
19 mm
manufacturerʼs engine warranty will be voided.
0.5 l
Please note: Only use containers designed and
NGK BPMR7A
approved for the purpose to transport and store fuel.
2300 ± 100 cuts/min
Pour the correct quantities of petrol and 2-stroke oil
13.33 m/s 2
into the mixing bottle (see scale printed on the
7.69 m/s 2
bottle). Then shake the bottle well.
97 dB
5.3 Fuel mixture table
107 dB
Mixing procedure: 40 parts petrol to 1 part oil
1 liters
5 liters

6. Operation

Please note that the statutory regulations governing
noise abatement may differ from town to town.
6.1 Starting the engine from cold (Fig. 3-5)
Fill the tank with the required amount of oil/petrol
mix.
1. Set the machine down on a hard, level surface.
2. Set the choke lever (Fig. 4/Item 5) to " ".
3. Press the fuel pump (primer) (Fig. 4/Item 9) 10
times.
4. Move the ON/OFF switch (Fig. 3/Item 6) to "I"
5. Secure the throttle lever. To do this, press the
throttle lever lock (Fig. 3/Item 13) and then press
the throttle lever (Fig. 3/Item 14) and lock the
throttle lever by pressing the locking knob (Fig.
3/Item 7) at the same time.
6. Hold the machine by the front handle in your
right hand and pull the starter cable (Fig. 5/Item
A) up to the first resistance point (approx. 10
cm). Then tug sharply on the starter cable 4
Petrol 2-stroke oil
25 ml
125 ml