Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Mac Afric ARC 400IT
Summary of Contents for Mac Afric ARC 400IT
- Page 1 ARC 400IT WELDING MACHINE USER MANUAL...
- Page 2 Preface This manual includes hardware description and operation introduction of the equipments. For your and other people’s safety, please read the manual carefully. Pay attention Pay attention to the words after the signs below. Sign Description The words after this sign means there is great potential danger, which may cause major accident, damage or even death, if it is not followed.
-
Page 3: Table Of Contents
CONTENTS SAFETY WARNING ············································································································ 4 MACHINE DESCRIPTION ···································································································· 9 TECHNICAL PARAMETERS TABLE ······················································································ 10 INSTALLATION INSTRUCTION ···························································································· 11 OPERATION INSTRUCTION ······························································································· 13 PANEL FUNCTION INSTRUCTION ······················································································· 14 NOTES OR PREVENTIVE MEASURES ················································································· 15 QUESTIONS TO BE RUN INTO DURING WELDING ································································ 16 MAINTENANCE ················································································································... -
Page 4: Safety Warning
SAFETY WARNING The safety notes listed in this manual is to ensure correct use of the machine and to keep you and other people from being hurt. The design and manufacture of welding machine considers safety. Please refer to the safety warning listed in the manual to avoid accidents. - Page 5 Please follow the rules below to avoid heavy accidents. Never use the equipment to do other things but welding. Follow related regulations for the construction of the input-driven power source, choice of place, usage of high-pressure gas, storage, configuration, safe-keeping of workpiece after welding and disposal of waste, etc.
- Page 6 Please follow the below notes to avoid fire and explode, etc. No combustible in welding area. Keep off combustible when welding. Keep hot workpiece after welding away from flammable gas. Do move away the combustible around when weld the dooryard, ground and wall,. ...
- Page 7 Please follow the notes below to avoid gas cylinder toppling over or broken. Use the gas cylinder correctly. Use the equipped or recommended gaseous regulator. Read the manual of gaseous regulator carefully before using it, and pay attention to the safety notes.
- Page 8 them from the power source and ensure the horizontal of the machine. Do fix the gas cylinder with belt or chain when moving it to avoid body hurt. Ensure fastness and insulation when lifting the wire feeder through the swing ring for welding. Electromagnetic interference needing attention.
-
Page 9: Machine Description
MACHINE DESCRIPTION The welding machine is a rectifier adopting the most advanced inverter technology. The development of inverter welding equipment profits from the development of the inverter power supply theory and components. The inverter welding power source utilizes high-power device IGBT to transfer 50/60Hz frequency up to 15KHz, then reduce the voltage and commutate, and output high-power voltage via PWM technology. -
Page 10: Technical Parameters Table
TECHNICAL PARAMETERS TABLE Model ARC 400IT Parameters Three Phase Three Phase Power voltage（V） AC 380V±15% AC 415V±15% ±15% ±15% Frequency （Hz） 50/60 50/60 Rated input current （A） 27.7 25.3 No-load voltage（V） VRD voltage (V) Output current（A） 40-400 Rated output voltage（V）... -
Page 11: Installation Instruction
Make sure there is no mistake and make sure the voltage difference among permission range. After the above job, installment is finished and welding is available. Attached components type list Mode ARC 400IT Rated current of Power switch ≥4mm2 Input side... - Page 12 Installation Diagram Power Supply Earth Clamp Workpiece Electrode Holder...
-
Page 13: Operation Instruction
OPERATION INSTRUCTION 1. Open the power switch, screen will show set current volume and ventilator is beginning to revolve. 2. Adjust knobs of welding current and arc-striking push, make welding function complies with demands. 3. Generally, welding current is adequate to welding electrode according with as following. Specification Φ1.6 Φ2.0... -
Page 14: Panel Function Instruction
PANEL FUNCTION INSTRUCTION ARC 400IT Front Panel Layout Remote control switch Current adjustment knob VRD switch ARC force adjustment knob VRD indicator Hot start adjustment knob Abnormal indicator Positive output terminal Current meter Remote control socket Voltage meter Negative output terminal... -
Page 15: Notes Or Preventive Measures
NOTES OR PREVENTIVE MEASURES Environment 1） The machine can perform in environment where conditions are dry with a dampness level of max 90%. 2） Ambient temperature is between -10 to 40 degrees centigrade. 3） Avoid welding in sunshine or drippings. Do not let water enter the gas. 4）... -
Page 16: Questions To Be Run Into During Welding
QUESTIONS TO BE RUN INTO DURING WELDING Fittings, welding materials, environment factor, supply powers maybe have something to do with welding. User must try to improve welding environment. A. Arc-striking is difficult and easy to pause: 1. Make sure quality of tungsten electrode is high. 2. -
Page 17: Maintenance
MAINTENANCE Remove dust by dry and clean compressed air regularly, if welding machine is operating in environment where is polluted with smokes and pollution air, the machine needs to be cleaned once a month. Pressure of compressed air must be within the reasonable range in order to prevent damaging to small components of inner-machine. -
Page 18: Troubleshooting And Fault Finding
TROUBLESHOOTING AND FAULT FINDING Notes: The following operations must be performed by qualified electricians with valid certifications. Before maintenance,please contact with us for professional suggestion. Fault symptom and solution. Fault symptom Solution 1. Make sure power switch is off. Meter doesn’t display, fan 2. -
Page 19: Appendix Circuit Diagram
APPENDIX CIRCUIT DIAGRAM CON13 CON16 CON12 XH-03 VH-03...
Need help?
Do you have a question about the ARC 400IT and is the answer not in the manual?
Questions and answers