Troubleshooting - Kruger SECOMAT 220 Operating Instructions Manual

on at temperatures below 15°C. This
heater only serves as support for the
functioning of the appliance and is not
to be used as heating for the room.
Water drainage
Wherever possible, the water should
drain automatically.
• Attach connector piece (optional ex-
tra) to the screw thread (8) at the bot-
tom of the machine
• Put the hose (optional extra) over the
connector piece
• Put the other end of the hose into the
waste pipe (preferably siphoned)
If the water is collected in a tank, it must
be regularly checked and emptied. De-
pending on the temperature and mois-
ture content of the air, the tank may
need to be emptied 1 – 2 times a day.
If the tank is not emptied, this can lead
to water damage.
Hanging up the washing
• Leave a minimum gap of 30 cm be-
tween the clothes and the machine
• Hang heavy cotton items (e.g. tow-
eling, jeans, pullovers etc.) in the air
flow near the machine
• Hang large items over two lines or at-
tach to two lines
• Ensure that the air circulation in the
room is adequate
• Do not obstruct the intake and outlet
openings
The most cost-effective way of drying
clothes is not to switch on the clothes
drier until:
a) you have hung up all the washing.
b) the drying room is full.
If other items are added during the
drying process, the drying time is in-
creased.
Starting the machine
• Close doors and windows
• Check machine is plugged into the
mains
• Set hygrostat controller (2) to 45%
relative humidity (washing should be
dry at this setting). If the washing is
not dry enough or is too dry, you can
change the setting as follows:
Washing is not dry enough
Set hygrostat to 35 – 40%
Washing is too dry
Set hygrostat to 50 – 55%
• SECOMAT 220 AH
STOP
DRY
20
30
• To switch on: Press the 'I' button
The clothes drier works automatically,
i.e. as long as the humidity in the room
remains above the preset value, it con-
tinues to operate. As soon as the set level
of humidity is reached, the dehumidify-
ing function of the clothes drier stops.
If the humidity level in the room rises
again, it automatically restarts.
• To switch off: Press the 'I' button
• SECOMAT 220 E
(with end stop)
• To switch on: Press the 'I' button
The clothes drier works automatically,
i.e. as long as the humidity in the room
remains above the preset value, it con-
tinues to operate. As soon as the set level
of humidity is reached, the clothes drier
switches off completely, i.e. it does not
come on again if the humidity level in
the room rises again. The drying process
can be interrupted at any time by press-
ing the 'O' button.
Cleaning
The refrigeration unit is hermetically
sealed and the fan bearings are provid-
ed with lifetime lubrication. These parts
are therefore maintenance-free.
• Wipe the housing with a damp
cloth.
• Take hold of the filter grip (5) at the
top of the front grill. Pull the filter up-
70
ward and remove.
60
50
• Remove dust from air filter using a
40
brush and replace
If it becomes particularly dirty, the inside
of the machine will need to be cleaned.
This must be performed by a refrigera-
tion specialist.

TROUBLESHOOTING

Please check the following points be-
fore taking the machine to a specialist
STOP
70
DRY
60 dealer.
20
50
40
30
A. Machine does not start
• Is the mains plug correctly inserted?
• Is the fuse in your fusebox OK?
• Is the mains cable or extension cable
(if used) OK?
• Is the hygrostat controller set correctly
(to approx. 45% relative humidity)?
B. Machine is running constantly
• Is the hygrostat controller set to ap-
prox. 45% relative humidity?
• Are the doors and windows closed?
C. The machine is not dehumidifying
the room properly
• Is the air circulation in the room ad-
equate?
• Are the intake and outlet openings
free of obstructions?
• Is the room temperature too high or
too low (see section on Installation)?
• Is the filter clean?
If you have checked the above points
and still not managed to rectify the
fault, the machine must be taken to a
refrigeration specialist for inspection.
DISPOSAL
Because the clothes drier contains a
refrigerant, it requires special disposal.
Please contact your specialist dealer or
local waste disposal authority.