Subscribe to Our Youtube Channel
Related Manuals for Narvon 378RBD2G1S
Summary of Contents for Narvon 378RBD2G1S
- Page 1 USER MANUAL REFRIGERATED BEVERAGE DISPENSER 4005332 #378RBD2G1S #378RBD2G2S #378RBD2G3S #378RBD2G4S SINGLE BOWL DOUBLE BOWL TRIPLE BOWL QUADRUPLE BOWL READ THOROUGHLY BEFORE OPERATION • UPDATED 04/2023 NARVON...
- Page 2 6.2 Monthly Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 NARVON...
- Page 3 ALWAYS place the unit on a stable surface in a fully vertical position. • Please keep 15cm (6") minimum air space all around the dispenser. • DO NOT put objects or fingers in panels, louvers, or faucet outlet. • DO NOT clean or service the machine unless it is switched off and unplugged. • This unit is not meant to be used outside. • This unit is not to be installed in areas subject to water spouts. • DO NOT use water jets to clean the unit or submerge the unit in water. • DO NOT operate if your hands or feet are wet. • This unit can work in a room temperature range between +5 degrees Fahrenheit and +32 degrees Fahrenheit. • DO NOT pour product inside the dispenser at a temperature higher than 40 degrees Fahrenheit. 2. SPECIFICATIONS #378RBD2G1S #378RBD2G2S #378RBD2G3S #378RBD2G4S Dimensions W x D x H (in.) 7 x 15¾ x 244/5 94/5 x 15¾ x 244/5 14½ x 15¾ x 244/5 197/10 x 15¾ x 244/5 Number of Bowls Capacity of Each Bowl 2 Gallon 2 Gallon 2 Gallon 2 Gallon Weight (lb.) (approx.) Adjustable Thermostats Power (W) NARVON...
- Page 4 (See Section 5 Cleaning and Sanitizing Procedures) 1 . In order to obtain a homogeneous mix, the product will need to be pre-mixed before being added to the machine. 2 . In your container, prepare 1 part beverage concentrate to 5 parts water and stir until completely mixed (Alter as directed for different products). 3 . While the machine is unplugged and switched OFF, pour your mix into the bowl. Make sure to not overfill by pouring only to the maximum level, as indicated on the bowl. 4 . Place the lid on the bowl to prevent contamination of the product 5 . Connect the machine to the power source and set the power switch to position I. 6 . When the machine is switched to Position I, power is turned on to refrigeration and the mixing devices. 7 . When your beverage is chilled to the proper temperature, dispense by pressing a glass/cup against the tap lever. 4.2 Operation Helpful Hints 1 . The length of time for cooling down the product is governed by many variables, such as ambient temperature and initial beverage temperature. 2 . To shorten product cooling time, pre-chill the product to be used in the dispenser. 3 . To shorten product cooling time, the bowl should be refilled after the product level drops lower than half. NARVON...
- Page 5 8 . Slide drip tray out and empty it. 5.2 Cleaning • DO NOT attempt to wash any machine components in a dishwasher. • Before any disassembly and/or cleaning procedure, make sure that the dispenser is disconnected from its power source. • When cleaning the machine, DO NOT allow excessive amounts of water around the electrically operated components of the unit. Electrical shock or damage to the machine may result. 1 . Users should utilize the three sink method to properly clean all components: a) Fill one basin with a neutral cleaning detergent mixed in lukewarm water. b) Leave one basin empty for rinsing. c) Fill a third basin with sanitizing solution mixed in lukewarm water. 2 . In the first basin, Thoroughly wash all components, except the lid, in the mild cleaning detergent with a soft cloth or sponge. 3 . Rinse all components in water. 4 . After rinsing, use a soft cloth or sponge to wipe down all of the components in the sanitizing solution. 5 . Rinse the components for a final time before leaving them out to dry. 6 . Wash the lids and the evaporator plates separately with a mild detergent and a soft cloth or sponge. Be careful not to damage any electrical components. NARVON...
- Page 6 5 . Gently place the bowl back on the unit by carefully FIG 5 hooking the rear end back into place and then fastening the front. (Fig. 7) FIG 6 FIG 7 6. ROUTINE MAINTENANCE IMPORTANT Maintenance to be carried out by qualified service personnel only. Daily Maintenance • Inspect the machine for signs of product leaks past seals and gaskets. If proper assembly does not stop leaks around seals or gaskets, check for improper lubrication, or worn or damaged parts. Replace parts as needed with original spare parts from the supplier. 6.2 Monthly Maintenance • Clean all internal components, primarily the condenser, using compressed air. • To clean these internal parts, unplug the unit or switch off the 2-pole wall breaker, then remove front panel (dispensing side). Condenser fins are very sharp, use extreme caution when cleaning. NARVON...
Need help?
Do you have a question about the 378RBD2G1S and is the answer not in the manual?
Questions and answers