Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Travis Industries Manuals
  4. Outdoor Light
  5. Tempest 94900748
  6. Quick start manual

Travis Industries Tempest 94900748 Quick Start Manual

50k lantern wall mount
Hide thumbs Also See for Tempest 94900748:

Advertisement

Quick Links

Download this manual
Overview
Tempest Lantern 50k - SKU 94900748
Packing List
Control Cover
Post
Wall Plate Cover
Wall Plate with Post Bracket
Rough-in Template
Head Mounting Brackets
Hardware Pack Components
(4) 2-1/2" Stainless Steel Lag Bolts and Washers
½" FPT to ½" MPT Elbow
Shutoff Valve - ½" FPT to 3/8" Flare
3/8" x 16" Stainless Flex Tubing
3/8" to 3/8" Tubing Connector
Page 1 of 11
Tempest™ 50k Lantern Wall Mount
(sku 94800832)
17602229 - 4/14/22
© Travis Industries, Inc.

Advertisement

loading
Need help?

Need help?

Do you have a question about the Tempest 94900748 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Travis Industries Tempest 94900748

Summary of Contents for Travis Industries Tempest 94900748

  • Page 1  ½” FPT to ½” MPT Elbow  Shutoff Valve - ½” FPT to 3/8” Flare  3/8” x 16” Stainless Flex Tubing  3/8” to 3/8” Tubing Connector Page 1 of 11 17602229 - 4/14/22 © Travis Industries, Inc.
  • Page 2 See the illustration below for details. NOTE: If the siding is thicker than 1” (26mm) add material behind the lantern mount so the base is not submerged more than 1” (26mm) into the siding. Page 2 of 11 17602229 - 4/14/22 © Travis Industries, Inc.
  • Page 3 Gas Line Location and Wall Plate Placement The gas line must be located correctly to allow proper placement of the shutoff valve under the wall plate cover. See the illustration below for details. Page 3 of 11 17602229 - 4/14/22 © Travis Industries, Inc.

  • Page 4: Installation

    2. Run the gas line to the correct location (see the illustration figure 3 details). Make sure the gas nipple protrudes between ¾” and 1-1/2” Install 24VDC electrical here Figure 2 Page 4 of 11 17602229 - 4/14/22 © Travis Industries, Inc.
  • Page 5 4. Place the wall plate on a suitable work surface and remove the (4) nuts (and washers) that hold the post bracket in place (see Figure 4). Remove the post bracket (see Figure 5). Figure 5 Figure 4 Page 5 of 11 17602229 - 4/14/22 © Travis Industries, Inc.
  • Page 6 WARNING: Seal the penetrations for the electrical and gas lines. Negative pressure in the building can cause heat failure of components. Figure 7 Figure 6 Seal electrical and gas line penetrations Figure 8 Page 6 of 11 17602229 - 4/14/22 © Travis Industries, Inc.
  • Page 7 Carefully remove the bottom cover from the lantern, make sure not to damage any gas or electrical components. 8. Remove the hinged control cover from the front of the stock cover and install it on the cover included with the wall mount kit. Page 7 of 11 17602229 - 4/14/22 © Travis Industries, Inc.
  • Page 8 10. Install the wall mount brackets onto the lantern base. Make sure the brackets are oriented properly. The lopped corners should face the front of the lantern (see illustration below). Use the nuts removed in the previous step to secure the bracket to the base. Page 8 of 11 17602229 - 4/14/22 © Travis Industries, Inc.
  • Page 9 NOTE: You may wish to level and square the wall mount if the post does not appear correct. Washers may be placed between the post bracket and wall plate to shim the post to the correct position. Page 9 of 11 17602229 - 4/14/22 © Travis Industries, Inc.
  • Page 10 8 (see Figure 19). Figure 15 Figure 14 Figure 16 Bolt the head to the post with (2) through- bolts removed in step 8 Figure 17 Figure 19 Figure 18 Page 10 of 11 17602229 - 4/14/22 © Travis Industries, Inc.
  • Page 11 17. Attach the control cover to the lantern using the thumbscrews removed in step 9 (see Figure 22). Figure 22 18. Complete assembly of the lantern (see the owner’s manual for details). Page 11 of 11 17602229 - 4/14/22 © Travis Industries, Inc.