Subscribe to Our Youtube Channel
Related Manuals for RJG Lynx IA1-S-VI-24
Summary of Contents for RJG Lynx IA1-S-VI-24
- Page 1 PRODUCT MANUAL PRODUCT MANUAL Lynx™ Surface‑ Analog Input Module with 24 V Power Supply IA1‑S‑VI‑24 Training and Technology for Injection Molding...
- Page 2 PRINT DATE 01.16.2023 REVISION NO.
-
Page 3: Table Of Contents
PRODUCT MANUAL Lynx™ Surface‑ Analog Input Module with 24 V Power Supply IA1‑S‑VI‑24 INTRODUCTION DISCLAIMER PRIVACY ALERTS PRODUCT DESCRIPTION APPLICATIONS PROCESS MONITORING AND CONTROL OPERATION INJECTION PRESSURE SCREW POSITION/VELOCITY DEW POINT OTHER SUPPORTED SENSOR TYPES DIMENSIONS CABLE LENGTH INSTALLATION INSTALLATION OVERVIEW IA1‑S‑VI‑24 eDART OR COPILOT SYSTEM CONNECTION INSTALLATION SPECIFICATIONS... - Page 4 Module with 24 V Power Supply IA1‑S‑VI‑24 MAINTENANCE CLEANING REGULAR CLEANING FUSE REPLACEMENT WARRANTY RJG, INC. STANDARD WARRANTY PRODUCT DISCLAIMER TROUBLESHOOTING COMMON INSTALLATION ERRORS NEGATIVE SCALING FOR STROKE FALSE CYCLE START ON PRESS POWER‑UP INCORRECT INJECTION PRESSURE SCALING CUSTOMER SUPPORT...
-
Page 5: Introduction
This guide must be kept available for reference at all times. DISCLAIMER PRIVACY Inasmuch as RJG, Inc. has no control Designed and developed by RJG, Inc. over the use to which others may put Manual design, format and structure this material, it does not guarantee that copyright 2018 RJG, Inc. - Page 6 NOTES Lynx™ Shielded Analog Input Module IA1‑S‑VI‑24 | Product Manual...
-
Page 7: Product Description
IA1‑M‑V using a cable (included with coolant pressure, coolant temperature, DMT142 or DMT143 purchase from RJG), delta pressure, dryer temperature, ejector which collects the signal for use with the pin (indirect) pressure, hydraulic pressure, eDART or CoPilot system. -
Page 8: Other Supported Sensor Types
OPERATION (continued) OTHER SUPPORTED SENSOR TYPES The IA1‑S‑VI‑24 also supports the additional following sensor types: • Ejector Pin (indirect) • Mold Deflection • Hydraulic Pressure • Power Used • Mold Temperature • Dryer Temperature • Barrel Temperature • Air Flow •... -
Page 9: Dimensions
DIMENSIONS CABLE LENGTH The C‑IA1/LX‑4M is 13 ft. (4 m) long. CABLE LENGTH Product Manual | Lynx™ Shielded Analog Input Module IA1‑S‑VI‑24... - Page 10 NOTES Lynx™ Shielded Analog Input Module IA1‑S‑VI‑24 | Product Manual...
-
Page 11: Installation
INSTALLATION INSTALLATION OVERVIEW The surface‑mount analog input module is mounted to a solid surface, such as the machine or mold. IA1‑S‑VI‑24 The surface‑mount analog input module cable C‑IA1/LX‑4M is wired directly to the machine (to an output card) on one end—or to some other 0–10 V/4–20 mA measurement device—and connected to the IA1‑S‑VI‑24 on the other using the... -
Page 12: Installation Specifications
INSTALLATION SPECIFICATIONS The instructions that follow are a general Remove all cables from the module, NOTES guide; actual steps necessary to install and remove module from mounting location if already mounted. this product will vary based on injection molding machine manufacturer, model, and 1. -
Page 13: Mounting
INSTALLATION SPECIFICATIONS (continued) MOUNTING Mount the IA1‑S‑VI‑24 module to a solid Attach the 0 V DC (white) wire to the surface—such as the molding machine common terminal of the injection molding or mold—using the supplied 10‑24 x 1.75” machine 0–10 V I/O card. Attach the 0–10 V socket head cap screws (2). -
Page 14: Edart System Software Setup
eDART SYSTEM SOFTWARE SETUP Each sensor type must be fully‑defined in the software for the IA1‑S‑VI‑24 and eDART system to provide accurate data. Always read and perform the following instructions to set up the IA1‑S‑VI‑24 module in the eDART system software. eDART SYSTEM VERSION 9.XX 5. -
Page 15: Copilot System Software Setup
SOFTWARE SETUP (continued) eDART SYSTEM VERSION 10.XX COPILOT SYSTEM SOFTWARE SETUP 1. Drag and drop the input from the Each sensor type must be fully‑defined in Available Sensor list in Machine Setup/ the software for the IA1‑S‑VI‑24 and CoPilot INPUTs to the desired position. system to provide accurate data. - Page 16 NOTES Lynx™ Shielded Analog Input Module IA1‑S‑VI‑24 | Product Manual...
-
Page 17: Ia1-S
Cables must be installed in areas free from module; remove lid from module. oil, dirt, grime, and grease. 2. Remove the used 24 V fuse ( below) RJG, Inc. recommends the following and discard. cleaners: 3. Insert new 24 V fuse. •... -
Page 18: Warranty
RJG, INC. STANDARD WARRANTY RJG, Inc. is not responsible for the improper installation of this equipment, or RJG, Inc. is confident in the quality and any other equipment RJG manufactures. robustness of the surface‑mount analog input module, and so are offering a Proper RJG equipment installation does one‑year warranty. -
Page 19: Troubleshooting
TROUBLESHOOTING COMMON INSTALLATION ERRORS INCORRECT INJECTION PRESSURE NEGATIVE SCALING FOR STROKE SCALING Problem: Negative value was entered in Problem: Injection pressure scaling is stroke scaling. incorrect. Solution: The analog input module cannot Solution: The eDART system and Lynx see negative voltages. The wiring must sensors eliminate the need for the manual have the positive (+) terminal on the analog scaling steps if injection pressure (for... -
Page 20: Customer Support
CUSTOMER SUPPORT Contact RJG’s Customer Support team by phone or email. RJG, Inc. Customer Support P: 800.472.0566 (Toll Free) P: +1.231.933.8170 email: support@rjginc.com www.rjginc.com/support Lynx™ Shielded Analog Input Module IA1‑S‑VI‑24 | Product Manual... -
Page 21: Related Products
Designed specifically for use with RJG, Inc.’s analog input module IA1‑M‑V and the eDART or CoPilot System, the C‑IA1‑M‑3M provides a connection from molding machines’ output card and the RJG, Inc. -
Page 22: Similar Products
DIN/LX‑D The Lynx communications adapter DIN/ LX‑D at right) is a shielded, DIN‑rail‑mounted module that interfaces other RJG, Inc. shielded machine interface modules with the eDART or CoPilot system when the ID7‑M‑SEQ is not used. This module is shielded to ensure high quality data... - Page 24 P +39 335 178 4035 P +01 231 947‑3111 sales@it.rjginc.com F +01 231 947‑6403 it.rjginc.com sales@rjginc.com www.rjginc.com MEXICO RJG MEXICO SINGAPORE RJG (S.E.A.) PTE LTD Chihuahua, Mexico Singapore, Republic of P +52 614 4242281 Singapore sales@es.rjginc.com P +65 6846 1518 es.rjginc.com sales@swg.rjginc.com en.rjginc.com...
Need help?
Do you have a question about the Lynx IA1-S-VI-24 and is the answer not in the manual?
Questions and answers