Related Manuals for RJG Lynx ID7-M-SEQ
Summary of Contents for RJG Lynx ID7-M-SEQ
- Page 1 PRODUCT MANUAL ™ S hielded equence odule ID7‑M‑SEQ raining and echnology for njecTion olding...
- Page 2 PRINT DATE 12.16.2019 REVISION NO.
-
Page 3: Table Of Contents
ALERTS PRODUCT DESCRIPTION APPLICATIONS PROCESS MONITORING AND CONTROL OPERATION MACHINE SEQUENCE SIGNALS eDART SEQUENCE SIGNALS DIMENSIONS CABLE LENGTHS INSTALLATION INSTALLATION OVERVIEW ID7‑M‑SEQ eDART CONNECTION INSTALLATION SPECIFICATIONS REQUIREMENTS MOUNTING WIRING CONNECTIONS Product Manual | Lynx™ Shielded Sequence Module ID7‑M‑SEQ RJG, Inc. - Page 4 ID7‑M‑SEQ MAINTENANCE CLEANING REGULAR CLEANING TESTING eDART VERSION 9.XX SOFTWARE eDART VERSION 10.XX SOFTWARE RJG, INC. STANDARD WARRANTY PRODUCT DISCLAIMER TROUBLESHOOTING COMMON ERRORS SIGNAL ERRORS ACCEPTABLE SIGNAL SUBSTITUTIONS CUSTOMER SUPPORT RELATED PRODUCTS COMPATIBLE PRODUCTS SHIELDED SEQUENCE MODULE CABLE C‑ID7‑M‑3M LYNX CABLES CE‑LX5...
-
Page 5: Introduction
DISCLAIMER ALERTS Inasmuch as RJG, Inc. has no control over the The following three alert types are used as use to which others may put this material, it needed to further clarify or highlight information... - Page 6 RJG, Inc. Lynx™ Shielded Sequence Module ID7‑M‑SEQ | Product Manual...
-
Page 7: Product Description
For example, the plastic cooling machine sequence is not directly derived from the molding machine, instead it is calculated by the eDART using the mold open signal—a machine‑ outputted sequence signal. Product Manual | Lynx™ Shielded Sequence Module ID7‑M‑SEQ RJG, Inc. -
Page 8: Operation
The eDART uses the injection forward signal as the start of the cycle. Without the injection forward signal, the eDART assumes the machine has stopped. RJG, Inc. Lynx™ Shielded Sequence Module ID7‑M‑SEQ | Product Manual... - Page 9 The mold opening signal indicates when the Position A, B, C, etc. mold is opening during a cycle. If the signal is on when the mold is opening, assign it as “mold opening”. Product Manual | Lynx™ Shielded Sequence Module ID7‑M‑SEQ RJG, Inc.
-
Page 10: Edart Sequence Signals
(version 9 software/Sequence Lights tool), the control is not in use, pack will only exist if the eDART cannot generate plastic cooling. fill signal is considered to be a fill and pack combined signal. RJG, Inc. Lynx™ Shielded Sequence Module ID7‑M‑SEQ | Product Manual... -
Page 11: Dimensions
DIMENSIONS CABLE LENGTHS The C‑ID7‑M‑3M is 9.8 ft. (3 m) long. CABLE LENGTH Product Manual | Lynx™ Shielded Sequence Module ID7‑M‑SEQ RJG, Inc. - Page 12 RJG, Inc. Lynx™ Shielded Sequence Module ID7‑M‑SEQ | Product Manual...
-
Page 13: Installation
C‑ID7‑M‑3M CABLE TO MACHINE CE‑LX5 CABLE TO eDART Product Manual | Lynx™ Shielded Sequence Module ID7‑M‑SEQ RJG, Inc. -
Page 14: Installation Specifications
Refer to “Machine Sequence Signals” on page 2 and “Wiring” on page 9 for more information on sequence signals and acceptable substitutions (if applicable). RJG, Inc. Lynx™ Shielded Sequence Module ID7‑M‑SEQ | Product Manual... -
Page 15: Wiring
Detects rotary table position in identify which position is active SHTL Cycle at Cycle at Position shuttle molding applications. for use with template control, Position 2 Position 1 alarm outputs, and summary value calculation. Product Manual | Lynx™ Shielded Sequence Module ID7‑M‑SEQ RJG, Inc. -
Page 16: Connections
C‑ID7‑M‑3M CABLE WIRING Second Stage any unused unused Screw Run Mold Brown Clamped Mold Yellow Opening Mold Closing any unused unused Manual Mode White Shuttle SHTL Green Position RJG, Inc. Lynx™ Shielded Sequence Module ID7‑M‑SEQ | Product Manual... -
Page 17: Maintenance
WARRANTY dirt, grime, and grease. RJG, INC. STANDARD WARRANTY RJG, Inc. recommends the following cleaners: RJG, Inc. is confident in the quality and • Microcare MCC‑CCC Contact Cleaner C robustness of the shielded machine interface modules, and so are offering a one‑year •... - Page 18 RJG, Inc. Lynx™ Shielded Sequence Module ID7‑M‑SEQ | Product Manual...
-
Page 19: Troubleshooting
Product Manual | Lynx™ Shielded Sequence Module ID7‑M‑SEQ RJG, Inc. -
Page 20: Acceptable Signal Substitutions
If no screw run signal is available, refer to the a set injection forward on time (detected by eDART version 9.xx or eDART version 10.xx eDART) software manuals for more information and instructions for screw run setup. RJG, Inc. Lynx™ Shielded Sequence Module ID7‑M‑SEQ | Product Manual... -
Page 21: Customer Support
CUSTOMER SUPPORT Contact RJG’s Customer Support team by phone or email. RJG, Inc. Customer Support P: 800.472.0566 (Toll Free) P: +1.231.933.8170 email: CustomerSupportGroup@rjginc.com www.rjginc.com/support Product Manual | Lynx™ Shielded Sequence Module ID7‑M‑SEQ RJG, Inc. - Page 22 RJG, Inc. Lynx™ Shielded Sequence Module ID7‑M‑SEQ | Product Manual...
-
Page 23: Related Products
RELATED PRODUCTS The shielded sequence module is compatible with other RJG, Inc. products for use with the eDART process control and monitoring system. COMPATIBLE PRODUCTS SHIELDED SEQUENCE MODULE CABLE C‑ID7‑M‑3M shielded sequence module cable C‑ID7‑M‑3M ( at right) cable features a metal sheathing and shielding suited for the heat and stress found in injection molding environments. -
Page 24: Similar Products
DIN/LX‑D The Lynx communications adapter DIN/LX‑D at right)is a shielded, DIN‑rail‑mounted module that interfaces other RJG, Inc. shielded machine interface modules with the eDART system when the ID7‑M‑SEQ is not used. This module is shielded to ensure high quality data... - Page 26 P +39 335 178 4035 P +01 231 947‑3111 sales@it.rjginc.com F +01 231 947‑6403 it.rjginc.com sales@rjginc.com www.rjginc.com MEXICO RJG MEXICO SINGAPORE RJG (S.E.A.) PTE LTD Chihuahua, Mexico Singapore, Republic of P +52 614 4242281 Singapore sales@es.rjginc.com P +65 6846 1518 es.rjginc.com sales@swg.rjginc.com en.rjginc.com...
Need help?
Do you have a question about the Lynx ID7-M-SEQ and is the answer not in the manual?
Questions and answers