Related Manuals for BLUE SKY SAT 265
Summary of Contents for BLUE SKY SAT 265
- Page 1 SAT 265 High Output Near-Field active studio monitor Blue Sky International 70 Sea Lane, Farmingdale, New York, 11735 USA • T: +1 516 249 1399 • F +1 516 249 8870 www.abluesky.com...
-
Page 2: Table Of Contents
Important Notes About the SAT 265 & This Manual Page 4 What is included? Page 4 SAT 265 Features Overview Page 5 A Tour of the SAT 265 Amplifier & Electronics Page 6 & 7 SAT 265 Mounting and Placement Page 8 System Signal Flow & Connections Page 9 Quick 2.1 System Setup Instructions... -
Page 3: Safety Instructions
It is IMPORTANT to confirm that the voltage this product, ask the service technician to perform safety checks selector switch on the back of the SAT 265 is set to the proper to determine that the product is in proper operating condition. -
Page 4: Sat 265 Introduction
212 for 2.1 operation and one or two are recommended for 5.1 operation. To that end we are proud to introduce the SAT 265. Blue Sky’s SAT 265 is a Please note, that these recommendations are not set in stone and will be... -
Page 5: Sat 265 Features Overview
500 to 2kHz pink noise = 90dB SPL @ 1M) to -22dB. For Tour of the SAT 265 Amplifier & Electronics]. more information please see page 6 & 7 [A Tour of the SAT 265 Amplifier & Electronics]. Tweeter Level Controls - The SAT 265 includes +/- 3dB of tweeter level adjustments, in 1dB increments. - Page 6 SET VOLTAGE 375 WATTS 250V 250V SWITCH BEFORE TURNING ON POWER Replace Only with Same Rating and Type designed in the USA made in China Page 6 • User Manual • A Tour of the SAT 265 Amplifier & Electronics...
- Page 7 265. For more information please see page 5 [SAT 265 Feature Overview] and page 14 [Measurement Data]. Power Switch - Controls the power to all the three amplifiers and all internal electronics. User Manual • A Tour of the SAT 265 Amplifier & Electronics • Page 7...
- Page 8 USER MANUAL • 6 • MOUNTING & PLACEMENT Monitor mounting and placement is often an afterthought, but in order to get the best imaging and overall performance from the SAT 265, it is important Center of the woofer to place the speakers correctly.
-
Page 9: System Signal Flow & Connections
(for best results, use identical subs) 2.1 SYSTEM SIGNAL FLOW & CONNECTIONS Above is a simple diagram showing how a SAT 265 / SUB 212 system Cable and connector wiring: may be wired for a stereo applications. The system shows a full-range... -
Page 10: Quick 2.1 System Setup Instructions
For more information with regard to the controls, please see the manual that came with the SUB 12 or SUB 15, and page 6 & 7 of this manual [A Tour of the SAT 265 Amplifier & Electronics]. -
Page 11: Expanded Calibration Guide
• 500-2.5kHz PINK NOISE -20dBFS.wav – a 500Hz to 2.5Hz SAT 265 to set 85 dBc. If you use this method you should make bandwidth limited pink-noise file recorded at 20dBFS •... -
Page 12: Subwoofer Placement Guide
SAT 265 USER MANUAL • 10 • SUBWOOFER PLACEMENT GUIDE So now that my system uses an integral subwoofer, how do I place it in my in the room, place the subwoofer in that location. Now, listen studio for the best possible low frequency performance? from the main position and confirm that the subwoofers response is similar to when the positions were reversed. - Page 13 SAT 265 USER MANUAL • 11 • TECHNICAL SPECIFICATIONS & DIMENSIONS Amplifiers & Electronics SAT 265 Specifications 3 x 100* Watts into 4-Ohm (for each woofer and tweeter) Enclosure .01% THD + noise at rated power @ 1 kHz .75” MDF with 1” front / rear baffle and internal bracing * Power is limited by protection circuitry .25”...
-
Page 14: Measurement Data
USER MANUAL • 12 • MEASUREMENT DATA Conditions: All SAT 265 measurements were made outdoors on a 58 inch stand at a distance of 1 meter. Since a 58 inch stand is not tall enough for accurate low-frequency measurements, a 1 meter ground plane measurement was also made and spliced in at 125 Hz on all measurements, to generate full frequency response. -
Page 15: Factory Service Instructions
Instructions For sales and other enquiries, please contact Blue Sky at: Service for the U.S. versions of Blue Sky products is available only from our authorized distributor, Group One Ltd., located in Farmingdale, New York. (Service for Blue Sky products outside the United States can be obtained Blue Sky International through local dealers or distributors.) If your monitor needs service, follow... - Page 16 Blue Sky International 70 Sea Lane, Farmingdale, New York, 11735 USA • T: +1 516 249 1399 • F +1 516 249 8870 www.abluesky.com...