Bosch 0.603.3B9.000 Original Instructions Manual page 12

OBJ_BUCH-2155-002.book Page 11 Wednesday, March 19, 2014 2:57 PM
Technical Data
Cordless dry vacuum cleaner
Article number
Container volume (gross)
Vacuum, max.
Airflow, max.
Weight according to
EPTA-Procedure 01/2003
Battery
Permitted ambient temperature
– when charging
– during operation*
– during storage
Recommended batteries
* Limited performance at temperatures <0
Assembly
Battery Charging
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium ion battery pack used in your vacuum cleaner.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithiucm-ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
The llithiucm-ion battery is protected against deep discharg-
ing by the "Electronic Cell Protection (ECP)". When the bat-
tery is empty, the machine is switched off by means of a pro-
tective circuit: The inserted tool no longer rotates.
 After the automatic shut-off of the vacuum cleaner, do
not continue to press the On/Off button. The battery
pack could become damaged.
Observe the notes for disposal.
Removing the battery (see figures A1 – A2)
The battery 3 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 11 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
– To remove the battery pack 3, press the battery unlocking
button 11 and pull the battery pack toward the rear out of
the vacuum cleaner. Do not exert any force when doing
this.
Mounting VAC Accessories (see figure B)
 Remove the battery before cleaning or performing
maintenance on the vacuum cleaner, making tool ad-
justments, changing accessories or storing the vacuum
cleaner. This safety measure prevents the vacuum cleaner
from being started accidentally.
Bosch Power Tools
The vacuum cleaner accessories can be connected directly to
the dust cup 5.
PAS 18 LI
The combination possibilities of the various vacuum cleaner
3 603 CB9 0..
accessories can be viewed in the figure.
l 0.65
– Connect the vacuum cleaner accessories firmly to the con-
nection at the dust cup 5 and in to each other.
kPa 4.2
3
m /min 1.4
Operation
 Remove the battery before cleaning or performing
kg 1.3
maintenance on the vacuum cleaner, making tool ad-
justments, changing accessories or storing the vacuum
cleaner. This safety measure prevents the vacuum cleaner
from being started accidentally.
°C 0...+45
°C –20...+50
Starting Operation
 Do not use the vacuum cleaner in damp environments.
°C –20...+60
GBA 18V x,xAh M-.
The penetration of rain or moisture into the top of the vac-
°C
uum cleaner increases the risk of an electric shock.
 Before vacuuming, ensure that the filter assembly is
assembled securely.
 Only use an undamaged filter (no cracks, small holes,
etc.). Replace a damaged filter immediately.
Switching On and Off
To save energy, only switch the vacuum cleaner on when us-
ing it.
– To switch on the vaccum cleaner, move the On/Off switch
2 forwards (direction ON).
– To switch off the vaccum cleaner, move the On/Off switch
2 backwards (direction OFF).
Maintenance and Service
Maintenance and Cleaning
 Remove the battery before cleaning or performing
maintenance on the vacuum cleaner, making tool ad-
justments, changing accessories or storing the vacuum
cleaner. This safety measure prevents the vacuum cleaner
from being started accidentally.
 For safe and proper working, always keep the vacuum
cleaner and ventilation slots clean.
– Clean the vacuum cleaner housing from time to time using
a moist cloth.
– Clean soiled charger contacts using a dry cloth.
Cleaning the Dust Cup (see figures C1 –C3)
To maintain the optimum performance of the vacuum cleaner,
clean the dust cup 5 after each use.
– Press release button 1 and remove the dust cup 5 from the
motor housing 4.
Remove the filter assembly 12 from the dust cup.
– Shake/tap out the dust cup 5 over a suitable waste bin.
– If required, clean the dust cup with a moist cloth.
If required, clean the filter assembly (see "Cleaning the Fil-
ter Assembly", page 12).
– Reinsert the filter assembly 12 into the dust cup 5.
Afterwards, hang the dust cup at the bottom into the motor
housing, apply light pressure until the dust cup can be
heard to engage.
English | 11
1 609 92A 0J0 | (19.3.14)