Table of Contents
Advertisement
the value of each item ('SIZE', and then each element, e.g.
'LIST1') and press k after each. After entering all items,
press ª, then press °2 and specify L1-4 to save the
data.
• To edit data saved in L1-4, press °1 and specify L1-4 to
recall the data to the list edit buffer. After editing, press ª,
then press °2 and specify L1-4 to save the data.
• Before performing calculations, press ª to close the list edit
buffer.
• When results of calculations are in the list format, the list edit
buffer with those results will be displayed. (At this time, you
cannot return to the equation.) To save the result in L1-4, press
ª, then press °2 and specify L1-4.
• Since there is only one list edit buffer, the previous data will be
overwritten by the new calculation.
• In addition to the 4 arithmetic functions, x
ing commands are available:
sortA list name
Sorts list in ascending order.
sortD list name
Sorts list in descending order.
dim( list name,size )
Returns a list with size changed as specified.
fill( value,size )
Enter the specified value for all items.
cumul list name
Sequentially cumulates each item in the list.
df_list list name
Returns a new list using the difference between
adjacent items in the list.
aug( list name,list name )
Returns a list appending the specified lists.
min list name
Returns the minimum value in the list.
max list name
Returns the maximum value in the list.
mean list name
Returns the mean value of items in the list.
med list name
Returns the median value of items in the list.
sum list name
Returns the sum of items in the list.
prod list name
Returns the multiplication of items in the list.
stdDv list name
Returns the standard deviation of the list.
vari list name
Returns the variance of the list.
o_prod( list name,list name ) Returns the outer product of 2 lists (vectors).
i_prod( list name,list name ) Returns the inner product of 2 lists (vectors).
abs list name
Returns the absolute value of the list (vector).
list→mat
Creates matrices with left column data from
(∑5)
each list. (L1→matA, L2→matB, L3→matC,
L4→matD)
Mode changes from list mode to matrix mode.
Creates a matrix with column data from each
list→matA
(∑6)
list. (L1, L2, L3, L4→matA)
Mode changes from list mode to matrix mode.
ERROR AND CALCULATION RANGES
Errors
An error will occur if an operation exceeds the calculation ranges,
or if a mathematically illegal operation is attempted. When an error
occurs, pressing < (or >) automatically moves the cursor
back to the place in the equation where the error occurred. Edit the
equation or press ª to clear the equation.
Error Codes and Error Types
Syntax error (Error 1):
• An attempt was made to perform an invalid operation.
Ex. 2 @{
Calculation error (Error 2):
• The absolute value of an intermediate or final calculation result equals
100
or exceeds 10
.
• An attempt was made to divide by 0 (or an intermediate calculation
resulted in zero).
• The calculation ranges were exceeded while performing calculations.
Depth error (Error 3):
• The available number of buffers was exceeded. (There are 10 buffers*
for numeric values and 24 buffers for calculation instructions in the
normal mode).
*5 buffers in other modes, and 1 buffer for Matrix/List data.
• Data items exceeded 100 in the statistics mode.
Equation too long (Error 4):
• The equation exceeded its maximum input buffer (142 characters).
An equation must be shorter than 142 characters.
Equation recall error (Error 5):
• The stored equation contains a function not available in the mode
used to recall the equation. For example, if a numerical value with
numbers other than 0 and 1 is stored as a decimal, etc., it cannot be
recalled when the calculator is set to binary.
Memory over error (Error 6):
• Equation exceeded the formula memory buffer (256 characters in total
in F1 - F4).
Invalid error (Error 7):
• Matrix/list definition error or entering an invalid value.
Dimension error (Error 8):
• Matrix/list dimensions inconsistent while calculation.
Invalid DIM error (Error 9):
• Size of matrix/list exceeds calculation range.
No define error (Error 10):
• Undefined matrix/list used in calculation.
Calculation Ranges
• Within the ranges specified, this calculator is accurate to ±1
of the least significant digit of the mantissa. However, a
calculation error increases in continuous calculations due
to accumulation of each calculation error. (This is the same
x
x
x
for y
,
¿ , n! , e
, ln , Matrix/List calculations, etc., where
continuous calculations are performed internally.)
Additionally, a calculation error will accumulate and become
larger in the vicinity of inflection points and singular points
of functions.
3
, x
2
, and x
–1
, the follow-
• Calculation ranges
–99
±10
~ ±9.999999999×10
If the absolute value of an entry or a final or intermediate result of
a calculation is less than 10
calculations and in the display.
BATTERY REPLACEMENT
Notes on Battery Replacement
Improper handling of batteries can cause electrolyte leakage or
explosion. Be sure to observe the following handling rules:
• Replace both batteries at the same time.
• Do not mix new and old batteries.
• Make sure the new batteries are the correct type.
• When installing, orient each battery properly as indicated in the
calculator.
• Batteries are factory-installed before shipment, and may be
exhausted before they reach the service life stated in the speci-
fications.
Notes on erasure of memory contents
When the battery is replaced, the memory contents are erased.
Erasure can also occur if the calculator is defective or when it is
repaired. Make a note of all important memory contents in case
accidental erasure occurs.
When to Replace the Batteries
If the display has poor contrast or nothing appears on the display
even when ª is pressed in dim lighting, it is time to replace
the batteries.
Cautions
• Fluid from a leaking battery accidentally entering an eye could
result in serious injury. Should this occur, wash with clean
water and immediately consult a doctor.
• Should fluid from a leaking battery come in contact with your
skin or clothes, immediately wash with clean water.
• If the product is not to be used for some time, to avoid damage
to the unit from leaking batteries, remove them and store in a
safe place.
• Do not leave exhausted batteries inside the product.
• Do not fit partially used batteries, and be sure not to mix
batteries of different types.
• Keep batteries out of the reach of children.
• Exhausted batteries left in the calculator may leak and damage
the calculator.
• Explosion risk may be caused by incorrect handling.
• Do not throw batteries into a fire as they may explode.
Replacement Procedure
1. Turn the power off by pressing @F.
2. Remove the two screws. (Fig. 1)
3. Slide the battery cover slightly and lift it to remove.
4. Remove the used batteries by prying them out with a ball-point
pen or other similar pointed device. (Fig. 2)
5. Install two new batteries. Make sure the "+" side is facing up.
6. Replace the cover and screws.
7. Press the RESET switch (on the back).
• Make sure that the display appears as shown below. If the
display does not appear as shown, remove the batteries, rein-
stall them and check the display once again.
(Fig. 1)
(Fig. 2)
Automatic Power Off Function
This calculator will turn itself off to save battery power if no key is
pressed for approximately 10 minutes.
SPECIFICATIONS
Calculations:
Scientific calculations, complex number
calculations, equation solvers, statistical
calculations, etc.
Internal calculations:
Mantissas of up to 14 digits
Pending operations:
24 calculations 10 numeric values in the
normal mode (5 numeric values in other
modes, and 1 numeric value for Matrix/
List data.)
Power source:
Built-in solar cells
3 V ¶ (DC):
Backup batteries
(Alkaline batteries (LR44 or equivalent) × 2)
Operating temperature: 0°C – 40°C (32°F – 104°F)
79.6 mm (W) × 154.5 mm (D) × 13.2 mm (H)
External dimensions:
3-1/8" (W) × 6-3/32" (D) × 17/32" (H)
Weight:
Approx. 97g (0.22 lb)
(Including batteries)
Batteries × 2 (installed), operation manual,
Accessories:
quick reference card and hard case
FOR MORE INFORMATION ABOUT
SCIENTIFIC CALCULATOR
Visit our Web site.
http://sharp-world.com/calculator/
SHARP CORPORATION
99
and 0.
–99
, the value is considered to be 0 in
Hide quick links:
Advertisement
Table of Contents
