Table of Contents
Advertisement
Quick Links
3/4 HP
HIGH TORQUE GARBAGE DISPOSER
2600 RPM
NOTE: This product may require approval of the relevant regulators and/or the sewerage system operator. Waste disposal must be installed according
to AS/NZS 3500.2 requirements.
ATS 5200.028
220-240V AC, 50/60 HZ
WM-022588
ITM. / ART. 37654
OWNER'S MANUAL
# QKGA05
Advertisement
Table of Contents
Related Manuals for Westinghouse QKGA05
Summary of Contents for Westinghouse QKGA05
- Page 1 NOTE: This product may require approval of the relevant regulators and/or the sewerage system operator. Waste disposal must be installed according to AS/NZS 3500.2 requirements. ATS 5200.028 220-240V AC, 50/60 HZ WM-022588 ITM. / ART. 37654 OWNER’S MANUAL # QKGA05...
-
Page 2: Table Of Contents
. in place to reduce the risk of objects falling into the disposer . WARNING: Switch off or unplug the appliance before attempting SAVE THESE INSTRUCTIONS to free a jammed rotor with an implement . QKGA05... -
Page 3: Warranty
Warranty TEN (10) YEAR LIMITED WARRANTY A thorough inspection must be made before installation and any damage must be promptly reported . We will not be liable for failures or damage that could have been discovered or avoided by proper inspection and testing prior to installation . Conglom Kitchen &... -
Page 4: Pre-Installation
Elbow gasket Rubber sink flange gasket Discharge elbow Flange elbow Flange Ring Screw Includes: Supporting plate *The waste disposer plug (provided) needs to be Top supporting ring (with 3 screws) controlled by an on/off switch (usually wall-mounted) . Cushion mount QKGA05... -
Page 5: Installation
Installation REMOVAL OF OLD UNIT CAUTION: Risk of electric shock . Turn off electric power at fuse box or circuit breaker before removing old unit . General instructions - your model may vary . NOTE: CAUTION: Be sure to support the disposer when removing the mounting ring or it may fall . -
Page 6: Installation Of The Mounting Assembly
Pull the flange ring open and press firmly until it snaps into place (Fig.8a). Top supporting ring - Tighten the 3 screws sequentially until the flange is very securely Supporting plate Top supporting attached to the sink . ring screw Fig . 8a QKGA05... -
Page 7: Attaching Discharge Elbow
Installation (continued) If at any time the bottom supporting ring becomes Slot disengaged from the body of the waste disposer, then: 1 . Align the slot in the bottom supporting ring with tab on the waste disposer body . 2 . Lower the bottom supporting ring and make the slot fit in the tab. -
Page 8: Connecting Disposer To Mounting Assembly
Cushion Mount (see Fig .13 and Fig .13a) . Bottom supporting ring Fig.13 Fig.13a If when you turn the bottom supporting ring it hits a limit before it tightens, then: 1 . Release and lower the waste disposer . QKGA05... -
Page 9: Dishwasher Connection
Installation (continued) 2 . Turn the bottom supporting ring 1/3 of a turn anti-clockwise . 3 . Lift the waste disposer and align it again . 4 . Tighten counter-clockwise the bottom supporting ring until it is tight . - Connect the bottom of the elbow to the trap by tightening the slip nut (Fig . 14) . - Run water and check all connections for leaks . -
Page 10: Operation
. GENERAL INSTALLATION DIMENSIONS 22 cm SINGLE BOWL 18 cm DOUBLE BOWL CENTER OUTLET DOUBLE BOWL END OUTLET approx 25 .7 cm approx 25 .7 cm approx 25 .7 cm 38 .8 cm 11 .9 cm 14 .5 cm QKGA05... -
Page 11: Troubleshooting
Troubleshooting Before seeking repair or replacement, we recommend that you review the following: Problem Solution The disposer is making loud noises . Other than the noises during grinding of small bones and fruit pits, these are usually caused by accidental entry of a spoon, bottle cap or other foreign objects . -
Page 12: Service Parts
Removable splash guard QHG109 Includes: Sink flange QHG110 Rubber sink flange gasket Flange ring Includes: Supporting plate QHG111 Top supporting ring (with 3 screws) Cushion mount Bottom supporting ring QHG112 Includes: Elbow gasket Discharge elbow QHG113 Flange elbow Screw QKGA05... - Page 13 Santry, Dublin 9, Ireland +61 2 87245218 | cs@conglomkb.com (service available Monday - Friday from 6:30 am - 3 pm AEDT) www.conglomkb.com Made in China and WESTINGHOUSE are trademarks of Westinghouse Electric Corporation. Used under license by Conglom International. All Rights Reserved.
Need help?
Do you have a question about the QKGA05 and is the answer not in the manual?
Questions and answers