Table of Contents
Advertisement
Quick Links
Introduction
To the owner or user: This service manual is
intended to provide you, and the maintenance or
service technician, with the information needed to
install, start up, clean, maintain and repair this
product.
The SLE300 is an ice machine that produces
cubed ice on 4 vertical cube freezing surfaces.
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Limitations
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation
General
Bin
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SLD dispenser . . . . . . . . . . . . . . . . . . . . . . . . . .
RS or IS dispenser . . . . . . . . . . . . . . . . . . . . . . . .
Plumbing
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Final Check List
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Component Location
Initial Start Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Sequence
Cleaning
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water/ Refrigeration Schematic . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Characteristics
Service Diagnosis
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal and Replacement
Parts lists and wiring diagrams are located in the center of this manual, printed on yellow paper.
Note the warning symbol where it appears in
this manual. It is an alert for important safety
information on a hazard that might cause
serious injury.
Keep this manual for future reference.
This manual was printed on recycled paper.
Table of Contents
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
When harvested, the cubes fall individually into the
ice storage bin. The SLE300 automatically
maintains the level of ice by turning on when the
ice level falls, and switches off when the bin is full.
The refrigeration system uses R-404A as the
refrigerant.
January 1995
Page 1
SLE300
page 2
page 3
page 4
page 5
page 6
page 7
page 8
page 9
page 10
page 11
page 12
page 13
page 14
page 16
page 18
page 19
page 22
Advertisement
Table of Contents
Related Manuals for Scotsman SLE300
Summary of Contents for Scotsman SLE300
- Page 1 The SLE300 is an ice machine that produces cubed ice on 4 vertical cube freezing surfaces. Specifications ....... .
-
Page 2: Specifications
If recharging, always use the charge listed on the ice machine. Specifications: The SLE300 will stack onto a variety of ice storage bins, see sales literature for proper ice storage bin. Model Number Dimensions W" x D" x H"... -
Page 3: For The Installer: Environmental Limitations
They meet or exceed the standards of UL, NSF, and CSA. Scotsman assumes no liability or responsibility of any kind for products manufactured by Scotsman that have been altered in any way, including the use of any part and/or other components not specifically approved by Scotsman. - Page 4 It must be installed indoors, in a controlled environment. The air and water temperatures must not exceed rated limits. Pre-installation: 1. Inspect the place where the ice machine is to be installed. Check for: space for the cabinet, water supply, drain availability and electrical power supply.
-
Page 5: Installation: Ice Storage Bin
5. If on a Scotsman bin, attach the ice machine to the bin using the straps and bolts shipped with the ice machine. Drill two 1/8" holes in the back of the bin and secure with sheet metal screws provided. -
Page 6: Installation: Sld150 Hotel Dispenser
SLE300 Installation: SLD150 Hotel Dispenser Assembly The ice machine must be placed onto the top of the dispenser, and the bin thermostat capillary tube routed into the bracket in the dispenser. 1. Check that the dispenser has a gasket all around the perimeter of the top, 22"... -
Page 7: Rs Or Is Dispenser
Installation: Scotsman IS or RS Dispenser Assembly: The assembly of the ice machine onto the dispenser requires two additional parts: an adapter kit and a thermostat stand off kit. 1. Mark two spots on the inside left liner of the dispenser: 2"... -
Page 8: Plumbing
SLE300 Installation Supply: Screw the 3/8" male flare (fitting shipped in package inside cabinet) into the 1/4" FPT fitting at the back of the cabinet (thread tape recommended). Connect cold potable water to the water inlet. A hand shut off valve for inlet water should be installed near the machine. -
Page 9: Electrical
A ground screw is provided in the junction box. Hand Disconnect Switch For The Electrician Follow All Local Codes - This Unit Must Be Grounded. Usually a licensed electrician will be required to connect the electrical service. Junction Box January 1995 Page 9 SLE300... -
Page 10: Final Check List
Scotsman. 12. Has the owner/user been given the name and telephone number of the authorized Scotsman Service Agency serving that location? January 1995 Page 10... -
Page 11: Component Location
Water Inlet Valve & Strainer Drain Elbow Component Location Control Box Detail Ice Size Thermostat Compressor Relay Ice Thickness Control Water Pump January 1995 Page 11 SLE300 High Pressure Cut Out Harvest Relay Thermostat Ice/Off/Wash Switch Control Box Bin Thermostat ICE/OFF/WASH Switch... -
Page 12: Initial Start Up
10. The water temperature in the reservoir will soon be 32 F., and ice should begin to form on the evaporators. 11. Allow the ice machine to operate for about Correct Size & 15-20 minutes. The ice should be fully formed and "... -
Page 13: Electrical Sequence
1. After ice has been harvested, but before new cubes begin to form, switch the ICE/OFF/WASH switch to WASH. 2. Add 4 oz. of ice machine cleaner to the reservoir. Allow unit to operate that way for 10 minutes. 3. Switch ICE/OFF/WASH switch to OFF 4. -
Page 14: Cleaning
2. Wipe all interior surfaces of the ice storage bin with the bleach and water. 3. Allow to air dry. To Remove Scale: 1. Mix a cleaning solution of 4 ounces of Scotsman Ice Machine Cleaner to 4 pints of warm F.-110 F.) water. -
Page 15: Cleaning: Ice Machine Water System
5. Drain the water from the sump by removing the drain elbow. 6. Disconnect hose from the water distributor pan, and remove the water distributor pan. 7. Mix a solution of 5 oz. ice machine cleaner and 1 gallon of warm (95 F. - 115 F.) water. -
Page 16: Refrigeration Schematic
Valve Water Reservoir Water Schematic: Water flows into the ice machine from its inlet connection at the back of the cabinet, through the inlet water valve and into the reservoir. The water in the reservoir is pumped up and through the water distributor tube at the top of the evaporators. -
Page 17: Harvest Cycle
Hot Gas Valve (Open) Thermostatic Expansion Valve Suction Line Siphon Tube (Draining) January 1995 Page 17 SLE300 Discharge Line Condenser Fan Motor (Off) Compressor Dryer Refrigeration Schematic... -
Page 18: Technical Characteristics
SLE300 Technical Characteristics Typical Cycle Time 18 minutes @ 90 F. air and 70 Typical Harvest Ice Weight 2.8 - 3.2 pounds Typical Low Side Pressure, 8 minutes into freeze 20 PSIG @ 70 F. Air 26 PSIG @ 90 F. -
Page 19: Service Diagnosis
No cooling at evaporator due to dirty condenser No cooling due to compressor not pumping January 1995 Page 19 SLE300 PROBABLE FIX Restore power Switch ICE/OFF/WASH switch to Check temperature at bin thermostat bracket, if warmer than F., thermostat should be closed. - Page 20 SLE300 Service Diagnosis: SYMPTOM No ice compressor is operating Ice is made, but not harvested. POSSIBLE CAUSE No cooling due to low refrigerant charge Ice size thermostat contacts do not switch position Ice will not slide down ice rack due to minerals on rack.
- Page 21 Adjust ice size thermostat; use gauge shipped with machine Check/replace heater on ice size thermostat probe tube. Clean water system with Scotsman Ice Machine Cleaner Clean tube with ice machine cleaner Check water supply pressure Check water supply for restrictions Check superheat, replace TXV if too high.
-
Page 22: Removal And Replacement
SLE300 Removal and Replacement Ice Size Thermostat: Before replacing the ice size thermostat, it should be positively determined that it is at fault. 1. Disconnect electrical power. Electrical shock hazard. Electrical shock can cause personal injury. Disconnect power before beginning to service components. - Page 23 3. Remove the screws holding the valve bracket to the liner. 4. Remove the valve from the ice machine. 5. Reverse the above steps to reassemble. Float Valve Siphon "U" Tube...
-
Page 24: Removal And Replacement: Refrigeration System
SLE300 Removal and Replacement: Refrigeration System This ice machine uses R-404A (HP62) refrigerant and polyolester oil. Do NOT use mineral oil in this refrigeration system. R-404A is a "Near Azeotrope" so liquid charging is required: When the system is serviced, a special liquid line drier is required. It is included with replacement compressors.
Need help?
Do you have a question about the SLE300 and is the answer not in the manual?
Questions and answers