Scotsman IS160 Service Manual
  1. Manuals
  2. Brands
  3. Scotsman Manuals
  4. Ice Maker
  5. IS160
  6. Service manual
Scotsman IS160 Service Manual

Scotsman IS160 Service Manual

Scotsman is160 ice machine: user guide
Hide thumbs
Table of Contents

Advertisement

Quick Links

INTRODUCTION
This service manual is intended as a reference for
the installer, user, and service agent of this
Scotsman Ice Station. It includes the necessary
information to install, start up, operate, clean and
maintain this unit.
Installing Loose Shipped Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3
For the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4
Service Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 11
Electrical Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 11
Parts lists and wiring diagrams are located in the center of this manual, printed on yellow
paper.
This manual contains important information, read it before beginning installation or operation.
Keep it for future reference.
Safety Symbol:
Important safety information on a
hazard that might cause serious
injury.

TABLE OF CONTENTS

August 1995
Page 1
IS160 and IS220

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IS160 and is the answer not in the manual?

Questions and answers

Related Manuals for Scotsman IS160

Summary of Contents for Scotsman IS160

  • Page 1: Table Of Contents

    INTRODUCTION This service manual is intended as a reference for the installer, user, and service agent of this Scotsman Ice Station. It includes the necessary information to install, start up, operate, clean and maintain this unit. Specifications ......... . . Page 2 Installing Loose Shipped Parts .

  • Page 2: Specifications

    They meet or exceed the standards of U.L., and N.S.F. Scotsman assumes no liability or responsibility of any kind for products manufactured by Scotsman that have been altered in any way, including the use of any parts and/or other components not specifically approved by Scotsman.

  • Page 3: Installing Loose Shipped Parts

    7. Attach the upper front cover by pushing the strikes on the cover into the catches on the unit. * Optional depending upon unit configuration. ICE CHUTE August 1995 Page 3 IS160 and IS220 LEVER SLOT ICE CHUTE MOUNTING PANEL...

  • Page 4: For The Installer

    IS160 and IS220 FOR THE INSTALLER 1. Locate the Ice Station on the counter. Allow vertical clearance above unit for the removal of the cover, and for pouring ice into the hopper. 2. Plan the unit drain. Two tubes ( "...
  • Page 5 Sealing may be accomplished by the use of room temperature vulcanizing (RTV) rubber sealant such as General Electric IS 808 Industrial Sealant, Dow Corning 731 (Scotsman part number 19-0529-01) or the equivalent. With the unit located on the counter as desired: A.

  • Page 6: Initial Start Up

    IS160 and IS220 INITIAL START UP 1. Sanitize the ice storage system as instructed on page 9. 2. Fill hopper with sanitary ice. Ice hopper contains parts that can move at any time, and will cause injury if hands are in the way.
  • Page 7 IS160 and IS220 FOR THE OPERATOR This section covers operating controls, daily pre-operation check, and unit operation. OPERATING CONTROLS - Units have either a lever or a push button. Lever: Ice will continue to be dispensed for as long as the lever is held in, or until the hopper is empty.

  • Page 8: How It Works

    IS160 and IS220 HOW IT WORKS The ice is stored in a hopper. At the front of the hopper there is an angled rotor: when that rotor turns, it scoops the ice, lifts it to the top of the ice chute and drops it through that chute into the user’s container.

  • Page 9: Cleaning & Sanitizing

    IS160 and IS220 CLEANING AND SANITIZING The sink, grill and splash panel area should be cleaned daily. The ice storage system should be sanitized monthly. Daily: 1. Lift up and remove grill from sink. 2. Use soap, hot water, and a clean cloth to wash sink and splash panel;...

  • Page 10: Cleaning And Sanitizing

    IS160 and IS220 CLEANING AND SANITIZING MONTHLY & INITIAL START UP: Sanitize the Ice Storage System. Note: this should only be done by qualified personnel. 1. Unplug the Ice Stand’s electrical cord from the electrical power. Ice hopper contains parts...

  • Page 11: Service Diagnosis

    5. Rotor will not turn 6. Relay for vend switch does not close during operation. August 1995 Page 11 IS160 and IS220 CORRECTION 1. Fill hopper with ice 2. Check vend switch, replace if open 3. Check drive motor, replace if not working 4.

  • Page 12: Removal And Replacement

    IS160 and IS220 REMOVAL & REPLACEMENT To Replace Vend Switch: 1. Disconnect Electrical Power. Electrical Shock Hazard. Unplug unit before servicing. 2. Pull out and remove upper front panel. Lever Type A. Twist ice chute 1/3 turn and pull down to remove.

This manual is also suitable for:

Is220

Table of Contents