Related Manuals for Meyer RT Series
Summary of Contents for Meyer RT Series
- Page 1 PB-RT-GK RT / RTX GRAIN KIT Installation / Operator’s Supplement Manual 2 / 2016 6990633 (1-13) Printed in U.S.A. © Bobcat Company 2013...
-
Page 2: Important Information
Always use your serial number when requesting information or when ordering parts. HOW TO READ YOUR SERIAL NUMBER EXAMPLE: 15TP3013 Model Year / Model / Sequence Of Build Meyer Manufacturing Corporation 574 West Center Avenue Dorchester, WI 54425 Phone: 1-800-325-9103 Fax: 715-654-5513 Email: sales@meyermfg.com... -
Page 3: Introduction
Meyer products the finest in the farm equipment industry today. There is no substitute for quality. That is why thousands of people like you have purchased Meyer farm equipment. They felt it was the best equipment to serve their farming needs, now and in years to come. We ask that you follow our policy of “safety first”, and we strongly suggest that you read through the Operator’s... - Page 4 Meyer Manufacturing Corporation - 4 - PB-RT-GK...
-
Page 5: Table Of Contents
TABLE OF CONTENTS 1.0 IMPORTANT INFORMATION ........... 2 2.0 INTRODUCTION . - Page 6 Meyer Manufacturing Corporation - 6 - PB-RT-GK...
-
Page 7: Safety
3.0 SAFETY The Meyer Grain Kit is manufactured with operator safety in mind. Located on the grain kit are various safety signs to aid in operation and warn of danger or caution areas. Pay close attention to all safety signs on the grain kit. -
Page 8: Safety Precautions
Always enter curves or drive up or down hills at a low speed and at a gradual steering angle. • Never allow riders on either tractor / truck or equipment. • Stay away from overhead power lines. Electrocution can occur without direct contact. • Use only properly rated undercarriage and tires. Meyer Manufacturing Corporation - 8 - PB-RT-GK... - Page 9 Safety Precautions For Installation: • Use lifting equipment with sufficient capacity to handle this unit • Park the forage box on a stable, level ground and securely chock all wheels. • Keep work area clean and free of oily or slippery materials to prevent slipping or falling while working on this equipment.
-
Page 10: Safety Signs
Do Not remove any safety signs. Safety signs are for operator protection and information. PART NO. 46-8100-6 PART NO. 46-0001-20 Meyer Manufacturing Corporation - 10 - PB-RT-GK... -
Page 11: Shutoff & Lockout Power
3.3 SHUTOFF & LOCKOUT POWER Any individual that will be adjusting, servicing, maintaining, or clearing an obstruction from this machine needs to ensure that this machine stays safely “OFF” until the adjustment, service, or maintenance has been completed, or when the obstruction has been cleared, and that all guards, shields, and covers have been restored to their original position. - Page 12 Meyer Manufacturing Corporation - 12 - PB-RT-GK...
-
Page 13: Pre-Operation
4.0 PRE-OPERATION 4.1 FALSE FRONT For grain kit installation, skip to section 4.2. STEP 2 STEP 1 Locate the second vertical upright from the front. Position the outside mount bracket (Item 1) flush Position the inner gate receiver bracket (Item 1) with the bottom of the upright's rear face. - Page 14 Do not unload out of the front with gate in forage box! When the False Front Gate and mounting brackets have been removed, reinstall the 1/2" bolts to fill the holes. Meyer Manufacturing Corporation - 14 - PB-RT-GK...
-
Page 15: Rear Belting And Main Roller Seal Cover
4.2 REAR BELTING AND MAIN ROLLER SEAL COVER Use the following 4 steps to install the rear belting and main roller seal cover to the forage box: STEP 1 STEP 2 Take the two formed sheet metal pieces (Item 1), Run the main apron chain until the chain slats are one for the left apron chain, and one for the right lined up above the rear main roller assembly. - Page 16 Manual page. Remove zip ties holding the tail light wire harness (Item 1) in the lower formed channel. Meyer Manufacturing Corporation - 16 - PB-RT-GK...
-
Page 17: Mount Brackets And Seal Plates
4.3 MOUNT BRACKETS AND SEAL PLATES Use the following step to install the mount brackets and seal plates to the forage box: STEP 1 Tarp system spool contains stored energy. Loosely attach the rear gusset plates (Item 1) with If the box has a tarp system on, release tension, bolts going in back to front while leaving the two loosen the second to back left upright spool bottom bolt holes empty. - Page 18 With the grain kit attached place the seal plate in position as shown above. Once the seal plate is flush with the upright drill both holes and attach with provided hardware. Meyer Manufacturing Corporation - 18 - PB-RT-GK...
-
Page 19: Grain Hopper Installation
4.4 GRAIN HOPPER INSTALLATION Use the following 5 steps to install the grain hopper to the forage box: STEP 1 STEP 2 NOTE: Use a lifting device and chains that are Raise the grain hopper until the grain hopper hanger mounts (Item 1) are aligned with the in good condition and of adequate size to lift the grain hopper. - Page 20 (Item 1) into the slot on the forage box frame. Tighten the handle nut (Item 2). Make sure the handle is pointing down prevent contact with the main apron chain. Repeat procedure on opposite side. Meyer Manufacturing Corporation - 20 - PB-RT-GK...
-
Page 21: Storing Stabilizing Legs
4.4.1 Storing Stabilizing Legs Use the following 2 steps to place the stabilizing legs into the storage location: STEP 1 STEP 2 Remove the retaining pin (Item 1) for the Push the stabilizing leg (Item 1) into the storage stabilizing leg (Item 2). position and install the retaining pin (Item 2). -
Page 22: Installing The Flow Control
For hydraulic hookup (See 4.4.3 Plumbing The Flow Control on page 23.). Once it is hooked up use the provided zip ties to secure all three hoses down to prevent contact with main apron chain. Meyer Manufacturing Corporation - 22 - PB-RT-GK... -
Page 23: Plumbing The Flow Control
4.4.3 Plumbing The Flow Control Use the following schematic to plumb the flow control: SINGLE DRIVE FLOW CONTROL SYSTEM Motor Rotation Viewed From Shaft End Port A Pressurized = CW Port B Pressurized = CCW Return Line REAR FRONT Pressure Line B (Return) A (Pressure) 1-800-325-9103... - Page 24 Meyer Manufacturing Corporation - 24 - PB-RT-GK...
-
Page 25: Operation
5.0 OPERATION DO NOT allow anyone to operate, service, inspect or otherwise handle this forage box until all operators have read and understand all of the instructional materials in this supplement manual and the forage box Owner's Operator's Manual and have been properly trained in its intended usage. - Page 26 Turn the flow control back to the 0 position and shut down the hydraulics. Close the grain kit unloading door, and engage the latch on the turn wheel. Meyer Manufacturing Corporation - 26 - PB-RT-GK...
-
Page 27: Maintenance
6.0 MAINTENANCE 6.1 LUBRICATION SHUTOFF & LOCKOUT POWER before adjusting, cleaning, lubricating or servicing the machine. (See 3.3 SHUTOFF & LOCKOUT POWER on page 11.) Fluid such as hydraulic fluid, grease, etc. must be disposed of in an environmentally safe manner. Some regulations require that certain spills and leaks on the ground must be cleaned in a specific manner. -
Page 28: Storing The Grain Kit
LOCKOUT / TAGOUT the machine / forage box. (See 3.3 SHUTOFF & LOCKOUT POWER on page 11.) Sometimes it may be necessary to store your Meyer grain kit for an extended period of time. Below is a list of items to perform before storage. -
Page 29: Replacement Parts
6.4 REPLACEMENT PARTS Before servicing this equipment, insure that all personnel, including family members are familiar with the equipment and the safety hazards that are present, along with the safety practices that should be observed while working in this equipment. Inspect the chassis’... - Page 30 Instructions sheets may be provided with your parts order. Otherwise, if available, instruction sheets can be e-mailed or faxed for your convenience. Call Meyer Manufacturing toll free at 1-800- 325-9103 or email sales@meyermfg.com. NOTE: Be environmentally friendly and dispose of any waste materials properly. Recycle when appropriate.
-
Page 31: Parts Repair And Replacement
7.0 PARTS REPAIR AND REPLACEMENT 1-800-325-9103 PB-RT-GK - 31 - www.meyermfg.com... -
Page 32: Rt / Rtx Grain Kit
RT / RTX GRAIN KIT 12 13 PB-RT-GK-009 Meyer Manufacturing Corporation - 32 - PB-RT-GK... - Page 33 KEY PART NUMBER QTY DESCRIPTION 400-1621-1 Main Body Weldment 400-1600-4 Center Divider Mount Bracket 400-1621-2 Center Divider 49-0303 Center Divider Belting 400-1600-5 Center Divider Mount Bracket 100-8180-5-2 Stabilizing Leg 33-0054 2.65 Self Seal One-Piece Weather Strip (Per Foot) 49-0310 Plexiglass Window 49-0315 Seal 400-1621-6...
- Page 34 RT / RTX GRAIN KIT (CONT’D) 12 13 PB-RT-GK-009 Meyer Manufacturing Corporation - 34 - PB-RT-GK...
- Page 35 KEY PART NUMBER QTY DESCRIPTION 400-1613 Door Rod Weldment 25-8062 Door Handle 400-1621-3 Poly Floor-Left 400-1621-4 Poly Floor-Right 56-0102 Lower Light LED Light Harness 56-0082 Oval Grommet 56-0115 6" Oval Red LED 56-0081 6" Oval Amber LED 56-0070-LED Clearance Light 2" Red With Grommet 56-0070-2 2"...
-
Page 36: Rt / Rtx False Front
RT / RTX FALSE FRONT PB-RT-GK-008 Meyer Manufacturing Corporation - 36 - PB-RT-GK... - Page 37 KEY PART NUMBER QTY DESCRIPTION 400-1612 Complete False Front Gate 400-1612-2 14.5" x 86" Painted Metal Panel 761II-40.75-86 40.75" x 86" Painted Metal Panel 49-0308 Bottom Seal Belting 400-1612-1 Gate Welded 25-6050-4 End Cap Trim 53-3/4" Long RTX-GKR-FFP-HDW RT/RTX False Front Gate Hardware Package 400-1622 Front Formed Cover-Upper 400-1616...
-
Page 38: Rt - Rtx Grain Kit Hydraulics
90 Degree ORB Bulkhead Adapter 55-0076-SAE Flow Control SAE 12 155-5602-12-12-12 Service Tee 155-CV-1906P Inline Check Valve 55-0079 3/4” Tee 55-0082 90 Degree Street Elbow 155-5405-08-12 Pipe Expansion Coupling 655-0023 3/4” x 54” Hose Meyer Manufacturing Corporation - 38 - PB-RT-GK... -
Page 39: Maintenance Record
MAINTENANCE RECORD MODEL NO. ____________________________________ SERIAL NO. ____________________________________ DATE SERVICE PERFORMED DATE SERVICE PERFORMED Manufactured by: Meyer Manufacturing Corporation 574 West Center Avenue Dorchester, WI 54425 Phone: 1-800-325-9103 Fax: 715-654-5513 Email: sales@meyermfg.com Website: www.meyermfg.com... - Page 40 Meyer Manufacturing Corporation 574 West Center Avenue Dorchester, WI 54425 Phone: 1-800-325-9103 Fax: 715-654-5513 Email: sales@meyermfg.com Website: www.meyermfg.com...
Need help?
Do you have a question about the RT Series and is the answer not in the manual?
Questions and answers