Table of Contents
Advertisement
Quick Links
INSTRUCTIONS FOR
Twin Pack 10.8V
Li-ion Cordless
Rotary Drill & Impact Driver
Stock No.20849
Part No.TP108VLI
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND
EFFECTIVE USE OF THIS PRODUCT.
GENERAL INFORMATION
These instructions accompanying the product are the original instructions. This document is part of the product, keep it
for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before
assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been designed, and
contains all the necessary information to ensure its correct and safe use. By following all the general safety instructions
contained in this manual, it will ensure both product and operator safety, together with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools
policy of continuous improvement determines the right to make modifications without prior warning.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Draper TP108VLI
Summary of Contents for Draper TP108VLI
- Page 1 AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
-
Page 2: Title Page
Commercial copying, redistribution, hiring or lending is prohibited. No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited. In all cases this copyright notice must remain intact. -
Page 3: Table Of Contents
CONTENTS 2.1 CONTENTS PAGE CONTENT PAGE TITLE PAGE INTRODUCTION ....................2 REVISION HISTORY................... 2 UNDERSTANDING THIS MANUAL ..............2 COPYRIGHT NOTICE ..................2 CONTENTS CONTENTS ......................3 GUARANTEE GUARANTEE ..................... 4 INTRODUCTION SCOPE ....................... 5 SPECIFICATION ....................5 HANDLING & STORAGE ................... 5 HEALTH &... -
Page 4: Guarantee
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorised. Your Draper guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the guarantee period. -
Page 5: Introduction
It is intended for domestic and light commercial use only. 4.2 SPECIFICATION Stock No..........................20849 Part No........................... TP108VLI Battery ..........................10.8V 10.8V Cordless Rotary Drill; Drill Capacities: Wood ........................25mm Mild Steel ...................... -
Page 6: Health & Safety Information
HEALTH & SAFETY INFORMATION 5.1 GENERAL SAFETY INSTRUCTIONS Do not overreach. Keep proper footing and balance at all times. This enables better control of General Power Tools Safety Warnings the power tool in unexpected situations. Dress properly. Do not wear loose clothing or WARNING: Read all instructions. -
Page 7: General Instructions For Battery Powered Tools & Chargers
HEALTH & SAFETY INFORMATION 5.2 GENERAL INSTRUCTIONS FOR Check that cutting tools are undamaged and are kept clean and sharp, this will maintain their operating BATTERY POWERED TOOLS & performance and lessen the loading on the tool. CHARGERS 5.3 SAFETY INSTRUCTIONS FOR MAINS POWERED BATTERY Good Working Practices/Safety The following suggestions will enable you to observe... -
Page 8: Instructions For Chargers And Batteries
NOTE: This information relates to the battery charging system for the Draper 10.8V cordless range. 5.6 LITHIUM-ION MATERIAL DATA SHEET a. -
Page 9: Technical Description
TECHNICAL DESCRIPTION 6.1 IDENTIFICATION 10.8V Rotary Drill 10.8V Impact Driver Variable speed trigger switch Variable speed trigger switch Forward/Reverse selector Forward/Reverse selector 10mm Keyless chuck ¼" Hex. (Female) quick release collet Torque collar LED work light Speed selector Battery charge indicator LED work light Belt clip Battery charge indicator... -
Page 10: Unpacking & Checking
Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the Draper Help Line (the telephone number appears on the Title page) and do not attempt to use the drill/impact driver. -
Page 11: Basic Cordless Rotary Drill Operations
BASIC CORDLESS ROTARY DRILL OPERATIONS 8.1 BATTERY CHARGING - FIGS. 1 - 2 FIG.1 Check the mains voltage. Make sure the voltage of the power source is the same as the voltage specified on the rating plate of the charger unit. Plug your mains plug into the power source. -
Page 12: Dust And Swarf
BASIC CORDLESS ROTARY DRILL OPERATIONS 8.2 DUST AND SWARF A correctly fitted dust mask, suitable for the activity and in accordance to the relevant standard must be worn. Swarf produced by metal drilling is extremely sharp. Take precautions when clearing swarf. The burr left on the hole is also sharp and should be removed with a suitable tool. -
Page 13: Torque Selection Control
BASIC CORDLESS ROTARY DRILL OPERATIONS 8.7 TORQUE SELECTION CONTROL - FIG. 6 FIG.6 By turning the collar it is possible to adjust the amount of torque. The logo represents maximum torque. Use this setting when drilling wood, metal and plastic. Settings 1-20 provide a facility for setting the torque to the required level. -
Page 14: Basic Cordless Impact Driver Operations
BASIC CORDLESS IMPACT DRIVER OPERATIONS 9.1 INSTALLING AND REMOVING BITS - FIG. 10 This driver is supplied with a ¼" Female Hex. Pull and hold the quick release collet outwards to insert and to release the bit. NOTE: This product is equipped with an electric brake. Never use any bits or accessories that are not hardened for impact use. -
Page 15: Holding The Impact Driver
BASIC CORDLESS DRILL/IMPACT DRIVER OPERATIONS 9.5 HOLDING THE DRILL/IMPACT DRIVER - FIG.13 FIGS. 13 - 14 The drill casing is designed to be held comfortably in two ways, 1. By the handle. 2. Or by the in-line support grip. FIG.14... -
Page 16: Maintenance
10. MAINTENANCE 10.1 MAINTENANCE Regular inspection and cleaning reduces the necessity for maintenance operations and will keep your tool in good working condition. The motor must be correctly ventilated during tool operation. For this reason avoid blocking the air inlets. -
Page 17: Troubleshooting
11. TROUBLESHOOTING NOTE: Remove plug and/or battery before carrying out any adjustment, servicing or maintenance. 10.8V Cordless Rotary Drill: Problem Cause Remedy Drill does not 1. Flat battery. 1. Charge battery. work. 2. Select forward or reverse. 2. Forward/Reverse not selected. Chuck does not 1. -
Page 18: Explanation Of Symbols
13. EXPLANATION OF SYMBOLS 13.1 EXPLANATION OF SYMBOLS Class II construction (Double insulated). WEEE Do not dispose of Waste Electrical & Electronic Equipment in with domestic rubbish For indoor use only. Do not expose to rain. Li-ion battery must be recycled or disposed of properly. Li-ion Fuse protective device. -
Page 19: Disposal
14. DISPOSAL 14.1 DISPOSAL At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. Contact your local authority for details of collection schemes in your area. In all circumstances: •... - Page 20 - Sales Desk: (023) 8049 4333 - General Enquiries: (023) 8026 6355 - Service/Warranty Repair Agent For aftersales servicing or warranty repairs, please contact the Draper Tools Help Line for details of an agent in your local area. YOUR DRAPER STOCKIST RDMC0916...
Need help?
Do you have a question about the TP108VLI and is the answer not in the manual?
Questions and answers