Table of Contents
Advertisement
Quick Links
20V
HAMMER
DRILL
89523
These instructions accompanying the product are the original instructions. This document is part of the product,
keep it for the life of the product passing it on to any subsequent holder of the product. Read all these
instructions before assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been
designed, and contains all the necessary information to ensure its correct and safe use. By following all the
general safety instructions contained in this manual, it will ensure both product and operator safety, together
with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the
product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper
Tools policy of continuous improvement determines the right to make modifications without prior warning.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Draper StormForce
Summary of Contents for Draper StormForce
- Page 1 AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
-
Page 2: Title Page
Commercial copying, redistribution, hiring or lending is prohibited. No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited. In all cases this copyright notice must remain intact. -
Page 3: Table Of Contents
2. CONTENTS 2.1 CONTENTS 1. TITLE PAGE 1.1 INTRODUCTION.......................... 1 1.2 REVISION HISTORY ........................2 1.3 UNDERSTANDING THIS MANUAL ..................... 2 1.4 COPYRIGHT NOTICE ......................... 2 2. CONTENTS 2.1 CONTENTS ..........................3 3. GUARANTEE 3.1 GUARANTEE ..........................4 4. INTRODUCTION 4.1 SCOPE............................ -
Page 4: Guarantee
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorised. Your Draper guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the guarantee period. -
Page 5: Introduction
It is intended for domestic and light commercial use only. Any other application is considered misuse. This power product is part of the Draper 20V Power Interchange range of power tools. All use universal 2.0 and 4.0Ah batteries and chargers, enabling each battery pack to fit all tools within the range (see the table on page 19 for the batteries and chargers available). -
Page 6: Health And Safety Information
5. HEALTH AND SAFETY INFORMATION When using any type of power tool there are steps that should be taken to make sure that you, as the user, remain safe. Common sense and a respect for the tool will help reduce the risk of injury. 5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE Warning! ●... -
Page 7: Additional Safety Instructions For Hammer Drills
5.2 ADDITIONAL SAFETY INSTRUCTIONS FOR HAMMER DRILLS Important: Draper Tools Limited recommends that this machine should not be modified or used for any application other than that for which it was designed. If you are unsure of its relative applications do not hesitate to contact us in writing and we will advise you. -
Page 8: Residual Risk
– Only use a correctly rated mains outlet to provide power, do not plug into site generators, attach to engine generators or D.C. sources. Do not use a mains socket outlet that is not switched. – Use the correct Draper charger in conjunction with it’s corresponding battery pack (see the table on page 19 for information). -
Page 9: Battery Packs
– Before charging, read the instructions. – For indoor use. Do not expose to rain. – Only use Draper battery packs with stock numbers 89437 and 89433 in conjunction with this product. – Do not charge any other manufacturer’s battery packs using Draper chargers. Any other application is considered misuse. -
Page 10: Technical Description
6. TECHNICAL DESCRIPTION 6.1 IDENTIFICATION 13mm Keyless chuck. Auxiliary hand grip. Variable speed trigger switch. Left-handed auxiliary hand grip mounting. Hand grip. Battery release button. LED Worklight. 20V 2.0Ah Li-ion battery pack. Belt clip. Forward/reverse selector. 2 Speed selector switch. Torque selection collar. -
Page 11: Unpacking And Checking
Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the Draper Helpline (the telephone number appears on the Title page) and do not attempt to use the product. -
Page 12: Battery Pack Charging
1 – 2 This power product is supplied with 2 × 2.0Ah battery packs and a 1 hour charger. Important: Only Draper designated battery packs and chargers can be used in conjunction with this product. Use of any other third party battery... -
Page 13: Battery Pack Charge Status
If there are no foreign objects, it is probable that the battery pack or charger is malfunctioning. Allow battery/charger to normalise and try again. If a fault remains after trying this then contact Draper Tools. 8.2 BATTERY PACK CHARGE STATUS –... -
Page 14: Basic Operation
9. BASIC OPERATION Warning! ● Dust and swarf – A correctly fitted dust mask, suitable for the activity and in accordance to the relevant standard must be worn. ● Swarf produced by metal drilling is extremely sharp. Take precautions when clearing swarf. -
Page 15: Variable Speed Trigger
9. BASIC OPERATION 9.3 VARIABLE SPEED TRIGGER – FIG.6 When the trigger is depressed, the drive will rotate (provided the direction switch is set in the forward or reverse position). This trigger switch is electronic which enables the user to vary the speed continuously. -
Page 16: Belt Clip
9. BASIC OPERATION 9.6 BELT CLIP – FIG.9 The spring steel belt clip is convenient for hanging the drill temporarily. The clip can be installed on either side of the tool. To install the clip: – Locate the clip in position and fasten with screw supplied, take care to not FIG.9... -
Page 17: Screwdriving
9. BASIC OPERATION 9.9 SCREWDRIVING To prevent slip or damage to the screw head, match the screwdriver bit to the screw head size. To remove screws: – Move the direction switch to the reversing position and apply pressure to the screw head and depress the trigger slowly). -
Page 18: Maintenance & Troubleshooting
10. MAINTENANCE & TROUBLESHOOTING 10.1 MAINTENANCE Regular inspection and cleaning reduces the necessity for maintenance operations and will keep your tool in good working condition. The motor must be correctly ventilated during tool operation. Avoid blocking the air inlets and vacuum the ventilation slots regularly. -
Page 19: Power Interchange Accessories
BATTERY PACKS/CHARGERS This power product is supplied with two 20V 2.0Ah Li-ion battery packs. The table below shows the Draper 20V Power Interchange compatible batteries and chargers available for this product. 20V Power Interchange tools all use universal 2.0 and 4.0Ah battery packs and chargers, enabling each battery pack to fit all tools within the range. -
Page 20: Disposal
12. DISPOSAL 12.1 DISPOSAL – At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. – Contact your local authority for details of collection schemes in your area. In all circumstances: ●... -
Page 21: Explanation Of Symbols
13. EXPLANATION OF SYMBOLS 13.1 EXPLANATION OF SYMBOLS Single value noise marking. (Maximum declared A-Weighted Read the instruction manual. sound power level in decibels). Wear face mask and safety Class II construction glasses. (Double insulated). WEEE – Waste Electrical & Wear ear defenders. - Page 22 NOTES - 22 -...
- Page 23 NOTES - 23 -...
- Page 24 ©Published by Draper Tools Limited. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.
Need help?
Do you have a question about the StormForce and is the answer not in the manual?
Questions and answers