Table of Contents
Advertisement
● Regarding the temperatures and charging time of the battery.
The temperatures and charging time will become as shown in Table 4
Type of battery
Temperatures at which the
battery can be recharged
Charging voltage
Battery
Charging time,
approx. (At 20°C)
NOTE
The recharging time may vary according to the ambient
temperature and power source voltage.
CAUTION
When the battery charger has been continuously used,
the battery charger will be heated, thus constituting
the cause of the failures. Once the charging has been
completed, give 15 minutes rest until the next charging.
7. Disconnect the charger's power cord from the
receptacle.
8. Hold the charger fi rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
CAUTION
○ If the battery is charged while it is heated because it has
been left for a long time in a location subject to direct
sunlight or because the battery has just been used, the
pilot lamp of the charger lights for 1 second, does not
light for 0.5 seconds (off for 0.5 seconds). In such a case,
fi rst let the battery cool, then start charging.
○ When the pilot lamp fl ickers (at 0.2-second intervals),
check for and take out any foreign objects in the charger's
battery connector. If there are no foreign objects, it is
probable that the battery or charger is malfunctioning.
Take it to your authorized Service Center.
○ Since the built-in micro computer takes about 3 seconds to
confi rm that the battery being charged with charger is taken
out, wait for a minimum of 3 seconds before reinserting it
to continue charging. If the battery is reinserted within 3
seconds, the battery may not be properly charged.
MOUNTING AND OPERATION
Action
Removing and inserting the
battery
Charging
Tightening torque adjustment
Selecting the drill position
Selecting the impact position
Change rotation speed
Removing and mounting the hook
Remaining battery indicator
(Main body)
Charger
V
14.4
BSL14xx series
(4 cells)
BSL1415S : 20
BSL1415 : 22
BSL1415X : 22
min.
BSL1420 : 30
BSL1425 : 35
BSL1430C : 45
Figure
Page
1
2
3
4
5
6
7
8
Table 4
UC18YFSL
0°C – 50°C
(8 cells)
(5 cells)
BSL1815S : 20
BSL1430 : 45
BSL1815 : 22
BSL1440 : 60
BSL1815X : 22
BSL1450 : 75
BSL1820 : 30
BSL1460 : 90
BSL1825 : 35
BSL1830C : 45
Remaining battery indicator
(Battery: BSL36A18)
How to use the LED light
Mounting the bit
Reversing the rotational direction
Switch operation
Charging a USB device from a
electrical outlet (UC18YSL3 only)
Charging a USB device and
battery from a electrical outlet
(UC18YSL3 only)
How to recharge USB device
(UC18YSL3 only)
When charging of USB device is
completed (UC18YSL3 only)
Selecting accessories
LED LIGHT WARNING SIGNALS
(Fig. 17)
This product features functions that are designed to protect
the tool itself as well as the battery. While the switch is
pulled, if any of the safeguard functions are triggered
during operation, the LED light will blink as described in
Table 5. When any of the safeguard functions are triggered,
immediately remove your fi nger from the switch and follow
the instructions described under corrective action.
12
12
12
12
12
12
13
13
8
Li-ion
18
BSL18xx series
(10 cells)
BSL1830 : 45
BSL1840 : 60
BSL1850 : 75
BSL1860 : 90
Fig. 17
Multi volt
series
(10 cells)
BSL36A18 : 75
9
13
10
13
11
14
12
14
13
14
14-a
14
14-b
14
15
15
16
15
―
16
Advertisement
Table of Contents
