Do you have a question about the ION ROBOT RV700 Series and is the answer not in the manual?
Questions and answers
glenn strand
January 21, 2025
there is a growling noise when model rv 700 travels
1 comments:
Mr. Anderson
May 14, 2025
A growling noise when the Shark ROBOT RV700 Series travels could be caused by obstructions or debris caught in the wheels or brushroll. Check the wheels and brushroll for anything stuck or wrapped around them, and remove it. Also, press down on the wheels and rotate them to ensure they move freely.
If a runner, rug or carpet e) Smoking or burning objects (hot supervision. 27. Use ONLY the Shark® charging dock edge that is less than eight inches from coals, cigarette butts, or matches) XDOCKRV750 and use only battery...
Page 3
ABOUT THE SHARK ION ROBOT® ABOUT THE SHARK ION ROBOT® With Auto-Sense® Navigation, your robot uses an array of sensors to navigate around walls, furniture legs, and other obstacles while it cleans. The robot may gently bump into obstructions or linger in one spot, and Charge Indicator Lights it may not cover every area in a single cleaning.
INSTALLING THE SIDE BRUSHES CHARGING Snap the 2 color-coded side brushes onto the IMPORTANT: The Shark ION Robot has a pre-installed rechargeable battery. Battery must be fully charged matching colored pegs on the bottom of the robot. before using. To charge, the Power button on the side of the robot...
CHARGING THE SHARK ION ROBOT® USING THE SHARK ION ROBOT® BUTTONS AND INDICATOR LIGHTS CHARGE INDICATOR LIGHTS CLEAN BUTTON Press to begin a cleaning In Use session. Press again to stop. Full Charge Nearly Full Mid Charge Low Charge While...
USING THE SHARK ION ROBOT ® MAINTENANCE USING THE SHARKCLEAN® APP AND VOICE CONTROLS CAUTION: Turn off power before performing any maintenance. The SharkClean app will guide you through easy setup of your robot. Control the unit remotely: • Schedule cleaning times for up to 7 days a week.
MAINTENANCE MAINTENANCE CLEANING THE FILTER CLEANING THE MULTI-SURFACE BRUSHROLL CLEAN FILTER EVERY WEEK. THE BRUSHROLL NEEDS OCCASIONAL MAINTENANCE. REPLACE FILTERS REGULARLY OR AS NEEDED. See sharkaccessories.com for replacement filters. REPLACE BRUSHROLL EVERY 6 to 12 MONTHS, OR WHEN VISIBLY WORN. See sharkaccessories.com for replacement parts.
MAINTENANCE MAINTENANCE CLEANING SENSORS AND CHARGING PADS CLEANING THE WHEELS CLEAN SENSORS AND CHARGING PADS PERIODICALLY AS NEEDED. With a dry cloth or cleaning brush, gently dust off REMOVE AND CLEAN FRONT WHEEL EVERY WEEK. REPLACE FRONT WHEEL EVERY 12 MONTHS. the sensors and pads located on the bottom of the robot.
MAINTENANCE MAINTENANCE REPLACING THE BATTERY TROUBLESHOOTING If any error lights are illuminated or flashing on your Shark Ion Robot®, see the error code chart below: ERROR CODE SOLUTION Power may be turned off or battery may need charging. Turn power ALL LED LIGHTS are off switch to On position.
END-USER LICENSE AGREEMENT FOR SHARKNINJA SOFTWARE END-USER LICENSE AGREEMENT FOR SHARKNINJA SOFTWARE IMPORTANT: PLEASE READ THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT CAREFULLY 5.6 You will not use the Ayla Application Libraries or Ayla Embedded Software to attempt to gain BEFORE CONTINUING WITH THIS PROGRAM INSTALL OR USE OF THIS PRODUCT: SharkNinja Operating unauthorized access to or use of the systems/services of SharkNinja’s other licensors;...
REGISTER YOUR PURCHASE BATTERY REMOVAL AND DISPOSAL This product uses a battery. When the battery no longer holds a charge, it should be removed from the vacuum and registeryourshark.com recycled. DO NOT incinerate or compost the battery. When your lithium-ion battery needs to be replaced, dispose ONE (1) YEAR LIMITED WARRANTY of it or recycle it in accordance with local ordinances or regulations.
Need help?
Do you have a question about the ION ROBOT RV700 Series and is the answer not in the manual?
Questions and answers
there is a growling noise when model rv 700 travels
A growling noise when the Shark ROBOT RV700 Series travels could be caused by obstructions or debris caught in the wheels or brushroll. Check the wheels and brushroll for anything stuck or wrapped around them, and remove it. Also, press down on the wheels and rotate them to ensure they move freely.
This answer is automatically generated