Page 1
CAR NAVIGATION SYSTEM SERVICE MANUAL MODEL: LAN1050EHGD...
Page 2
[CONTENTS] SECTION 1. SPECIFICATION SECTION 2. NAME OF EACH PART SECTION 3. OVERALL BLOCK DIAGRAM SECTION 4. EXPLODED VIEWS SECTION 5. FRONT PART SECTION 6. MAIN PART SECTION 7. AUDIO PART SECTION 8. TROUBLESHOOTING GUIDE...
SPECIFICATION GENERAL Output Power ......................Digital Output (S/PDIF) Power Source ..........................DC 14.4 V Ground System ..........................Negative Dimensions (W x H x D) ...................263.3 x 136.8 x 199.7 mm Net Weight ............................2.65 kg DISPLAY LCD ........................17.78 cm (7 inch) TFT LCD Resolution ..........................
CONTROL PANEL 1. Disc slot • Traffic: shows the traffic information. - Traffic info on route: the list of traffic 2. RESET hole information on active route Press with thin object to reset the unit when it - Traffic info nearby: the list of traffic information does not operate normally.
STEERING WHEEL REMOTE CONTROL 1. Volume ( Increases or decreases the volume level. Press to hang up a call. Mutes the volume. Press to select a source. FM → AM → CD → USB (or iPod) → BT → AUX → FM... •...
FRONT BLOCK DIAGRAM < Main Block > < Front Block Diagram > CVBS (Rear Camera) R [7~0] R [7~2] G [7~0] G [7~2] B [7~0] B [7~2] PCLK CLKH Video BIAS CLKV Decoder HSYNC LCLK (TW8816) VSYNC FCLK MAIN BOARD VCOM VOLTAGE 3.3 V 7.0”...
POWER BLOCK DIAGRAM LT3481 3.75 V DCDC1(90 %) VDDY 1.8 V 120 mA B/UP MAX 2.7 A MAX 1500 mA DDR 1.8 V 1200 mA VDDX 3.3 V 65 mA DCDC2(85 %) SYSTEM 3.3 V 1000mA MAX 1200 mA DCDC3(87 %) VDDI 1.2 V 600 mA MAX 1000 mA BA33BC0FP...
Page 25
AUDIO CONNECTOR PIN DESCRIPTON A. POWER & SIGNAL CONNECTOR B. CAMERA & TMU CONNECTOR KET MG644408 (42PIN) TYCO AMP 1318853 (24PIN) NUMBER Name NUMBER NAME NUMBER NAME CAMERA_CVBS BATT_B+ AUTO_LIGHT CAMERA_B+ MM_CAN_L AUX_L HS_CAN_L AUX_GND NAVI_VOICE+ AUDIO+[ECALL] AUX_R NAVI_VOICE- TMU_GND RS422_RX+_TMU ILL+ REVERSE_GEAR...
SECTION 8. TROUBLESHOOTING GUIDE [CONTENTS] • GENERAL PART (NAVIGATION) ........... . . 8-1...
Page 29
GENERAL PART (NAVIGATION) Cannot identify current location. (GPS not receiving) GPS cannot be used indoors and must be connected to a power source with ACC in a vehicle in a location where the signal from the satellite can be received easily. When initially connecting the GPS, it usually takes about 10 minutes to be working normally, but the connection speed can differ depending on the weather condition and surrounding obstacles.
Page 30
Map matching As mentioned, the GPS systems used by this Navigation System are susceptible to certain errors. Their calculations may on occasion place you to a location on the map where no road exists. In this situation, the processing system understands that vehicles travel only on roads, and is able to correct your position by adjusting it to a nearby road.
Page 31
Trouble Shooting Guide Symptom Correction The Sceen is White. Case1) Replace Front Assy's 1) It is partially white screen. 2) All Button is working. The Screen is White. Case2) Replace Main BD 1) It is completely white screen. 2) All Button is not working. CD Deck is not Working.
Need help?
Do you have a question about the LAN1050EHGD and is the answer not in the manual?
Questions and answers